E5CNH E5AN-H E5EN-H Digital Controllers User's Manual - OMRON

Initial Setting Level Section 5-9
Setting
Set one of the set values from the following table.
The default is 5.
If a platinum resistance thermometer is mistakenly connected while a setting
for other than a platinum resistance thermometer is in effect, S.ERR
will be displayed. To clear the S.ERR display, check the wiring and then
cycle the power.
Input type Specifications Set value Input temperature range
Platinum resistance Pt100 0 −200.0 to 850.0 (°C)/−300.0 to 1,500.0 (°F)
thermometer
1 −199.9 to 500.0 (°C)/−199.9 to 900.0 (°F)
2 0.0 to 100.0 (°C)/0.0 to 210.0 (°F)
JPt100 3 −199.9 to 500.0 (°C)/−199.9 to 900.0 (°F)
4 0.0 to 100.0 (°C)/0.0 to 210.0 (°F)
Thermocouple K 5 −200.0 to 1,300.0 (°C)/−300.0 to 2,300.0 (°F)
6 −20.0 to 500.0 (°C)/0.0 to 900.0 (°F)
J 7 −100.0 to 850.0 (°C)/−100.0 to 1,500.0 (°F)
8 −20.0 to 400.0 (°C)/0.0 to 750.0 (°F)
T 9 −200.0 to 400.0 (°C)/−300.0 to 700.0 (°F)
10 −199.9 to 400.0 (°C)/−199.9 to 700.0 (°F)
E 11 −200.0 to 600.0 (°C)/−300.0 to 1,100.0 (°F)
L 12 −100.0 to 850.0 (°C)/−100.0 to 1,500.0 (°F)
U 13 −200.0 to 400.0 (°C)/−300.0 to 700.0 (°F)
14 −199.9 to 400.0 (°C)/−199.9 to 700.0 (°F)
N 15 −200.0 to 1,300.0 (°C)/−300.0 to 2,300.0 (°F)
R 16 0.0 to 1,700.0 (°C)/0.0 to 3,000.0 (°F)
S 17 0.0 to 1,700.0 (°C)/0.0 to 3,000.0 (°F)
B 18 100.0 to 1,800.0 (°C)/300.0 to 3,200.0 (°F)
W 19 0.0 to 2,300.0 (°C)/0.0 to 3,200.0 (°F)
PLII 20 0.0 to 1,300.0 (°C)/0.0 to 2,300.0 (°F)
K 21 −50.0 to 200.0 (°C)/−50.0 to 200.0 (°F)
J 22 −50.0 to 200.0 (°C)/−50.0 to 200.0 (°F)
T 23 −50.0 to 200.0 (°C)/−50.0 to 200.0 (°F)
Platinum resistance
thermometer
Pt100 24 −50.0 to 200.0 (°C)/−50.0 to 200.0 (°F)
Current input 4 to 20 mA 25 One of the following ranges depending on the scal-
Voltage input
0 to 20 mA
1 to 5 V
26
27
ing.
−19999 to 32400
−1999.9 to 3240.0
0 to 5 V 28 −199.99 to 324.00
0 to 10 V 29
−19.999 to 32.400
See
■ Related Parameters
Temperature unit, Set point upper limit, Set point lower limit (initial setting
level): Page 226
225