E5CNH E5AN-H E5EN-H Digital Controllers User's Manual - OMRON

More documents

Recommendations

Info

Advanced Function Setting Level Section 5-10 rac ON/OFF Counter Reset Function Setting See 280 This parameter resets the ON/OFF counter for specified control outputs. Note After the counter has been reset, the set value will be automatically returned to 0. ■ Related Parameters cmov Move to Calibration Level Function See Control outputs 1 and 2 must be supported. Relay, or voltage outputs (for driving SSR), or SSR output must be used. Setting range Default 0: Disable the counter reset function. 0 1: Reset the control output 1 ON/OFF counter. 2: Reset the control output 2 ON/OFF counter. Control output 1 ON/OFF count monitor, Control output 2 ON/OFF count monitor (advanced function setting level): Page 278 Initial setting/communications protect must be 0. This parameter sets the password to move to the calibration level. Set the password to move to the calibration level. The password is 1201. Move to the calibration level either by pressing the M Key or O Key or by waiting for two seconds to elapse. ■ Related Parameter Initial setting/communications protect (protect level): Page 172
Communications Setting Level Section 5-11 5-11 Communications Setting Level psel Protocol Setting Communications must be supported. u-no Communications Unit No. bps Communications Baud Rate len Communications Data Length CompoWay/F must be selected as the protocol. sbit Communications Stop Bits CompoWay/F must be selected as the protocol. prty Communications Parity sdwt Send Data Wait Time See Each parameter is enabled when the power is reset. Match the communications specifications of the E5@N-H and the host computer. If multiple devices are connected, ensure that the communications specifications for all devices in the system (except the Communications unit number) are the same. Item Symbol Set values Settings Default Protocol setting psel cwf, mod CompoWay/F (SYSWAY), Modbus cwf Communications Unit No. u-no 0 to 99 0 to 99 1 Communications bps 1.2, 2.4, 4.8, 9.6, 1.2, 2.4, 4.8, 9.6, 9.6 baud rate 19.2, 38.4, or 57.6 19.2, 38.4, or 57.6 (kbps) (kbps) Communications data length len 7 or 8 bits 7 or 8 bits 7 Stop bits sbit 1 or 2 bits 1 or 2 bits 2 Communications parity prty none, even, odd None, Even, Odd even Send data wait time sdwt 0 to 99 0 to 99 (ms) 20 ■ Related Parameter Communications writing (adjustment level): Page 193 281
Page 1:
SUB1 SUB2 SUB3 HA OUT1 STOP OUT2 CW
Page 5 and 6:
Preface The E5CN-H, E5AN-H, and E5E
Page 7 and 8:
Disclaimers CHANGE IN SPECIFICATION
Page 9 and 10:
■ Safety Precautions CAUTION Do n
Page 11 and 12:
Precautions for Safe Use Be sure to
Page 13 and 14:
● Ensuring Measurement Accuracy W
Page 15 and 16:
Power supply ● Ferrite Core Conne
Page 17 and 18:
Conventions Used in This Manual Mea
Page 19 and 20:
TABLE OF CONTENTS SECTION 1 Introdu
Page 21 and 22:
About this Manual: This manual desc
Page 23 and 24:
SECTION 1 Introduction This section
Page 25 and 26:
Names of Parts Section 1-1 E5EN-H 1
Page 27 and 28:
I/O Configuration and Main Function
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Setting Level Configuration and Key
Page 35 and 36:
Setting Level Configuration and Key
Page 37 and 38:
Communications Function Section 1-4
Page 39 and 40:
SECTION 2 Preparations This section
Page 41 and 42:
Installation Section 2-1 2-1-2 Pane
Page 43 and 44:
Installation Section 2-1 2-1-3 Moun
Page 45 and 46:
Installation Section 2-1 Mounting t
Page 47 and 48:
Installation Section 2-1 E5AN/EN-H
Page 49 and 50:
Installation Section 2-1 1,2,3... 1
Page 51 and 52:
Wiring Terminals Section 2-2 E5AN/E
Page 53 and 54:
Wiring Terminals Section 2-2 Contro
Page 55 and 56:
Wiring Terminals Section 2-2 Take c
Page 57 and 58:
Wiring Terminals Section 2-2 Take c
Page 59 and 60:
Wiring Terminals Section 2-2 CT Inp
Page 61 and 62:
Wiring Terminals Section 2-2 RS-232
Page 63 and 64:
Using the Support Software Port Sec
Page 65 and 66:
Using Infrared Communications Secti
Page 67 and 68:
SECTION 3 Basic Operation This sect
Page 69 and 70:
Initial Setting Examples Section 3-
Page 71 and 72:
Setting the Input Type Section 3-2
Page 73 and 74:
Selecting the Temperature Unit Sect
Page 75 and 76:
Setting Output Specifications Secti
Page 77 and 78:
Setting Output Specifications Secti
Page 79 and 80:
Using ON/OFF Control Section 3-7 To
Page 81 and 82:
Using ON/OFF Control Section 3-7 In
Page 83 and 84:
Determining PID Constants (AT, ST,
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Alarm Outputs Section 3-9 2.d 45.0
Page 91 and 92:
Alarm Outputs Section 3-9 3-9-2 Ala
Page 93 and 94:
Using Heater Burnout, Heater Short,
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Setting the No. 3 Display Section 3
Page 107 and 108:
SECTION 4 Applications Operations T
Page 109 and 110:
Shifting Input Values Section 4-1 4
Page 111 and 112:
Shifting Input Values Section 4-1 F
Page 113 and 114:
Alarm Hysteresis Section 4-2 For ex
Page 115 and 116:
Executing Heating/Cooling Control S
Page 117 and 118:
Executing Heating/Cooling Control S
Page 119 and 120:
Using Event Inputs Section 4-5 Cont
Page 121 and 122:
Using Event Inputs Section 4-5 Cont
Page 123 and 124:
Setting the SP Upper and Lower Limi
Page 125 and 126:
Using the SP Ramp Function to Limit
Page 127 and 128:
Moving to the Advanced Function Set
Page 129 and 130:
Using the Key Protect Level Section
Page 131 and 132:
PV Change Color Section 4-10 4-10 P
Page 133 and 134:
PV Change Color Section 4-10 colr r
Page 135 and 136:
Alarm Delays Section 4-11 Note (1)
Page 137 and 138:
Loop Burnout Alarm Section 4-12 Par
Page 139 and 140:
Loop Burnout Alarm Section 4-12 Ini
Page 141 and 142:
Performing Manual Control Section 4
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Using the Transfer Output Section 4
Page 149 and 150:
Using the Transfer Output Section 4
Page 151 and 152:
Using Banks and PID Sets Section 4-
Page 153 and 154:
Using Banks and PID Sets Section 4-
Page 155 and 156:
Using the Simple Program Function S
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Output Adjustment Functions Section
Page 165 and 166:
Output Adjustment Functions Section
Page 167 and 168:
Using the Extraction of Square Root
Page 169 and 170:
Setting the Width of MV Variation S
Page 171 and 172:
Setting the PF Key Section 4-20 Set
Page 173 and 174:
Counting Control Output ON/OFF Oper
Page 175 and 176:
Displaying PV/SV Status Section 4-2
Page 177 and 178:
Using a Remote SP Section 4-23 4-23
Page 179 and 180:
Position-proportional Control Secti
Page 181 and 182:
Logic Operations Section 4-25 Manua
Page 183 and 184:
Logic Operations Section 4-25 Examp
Page 185 and 186:
Logic Operations Section 4-25 4. Se
Page 187 and 188:
Logic Operations Section 4-25 11. C
Page 189 and 190:
Logic Operations Section 4-25 Opera
Page 191 and 192:
This section describes the individu
Page 193 and 194:
Protect Level Section 5-2 5-2 Prote
Page 195 and 196:
Protect Level Section 5-2 wtpt Sett
Page 197 and 198:
Operation Level Section 5-3 5-3 Ope
Page 199 and 200:
Operation Level Section 5-3 Functio
Page 201 and 202:
Operation Level Section 5-3 bank Ba
Page 203 and 204:
Operation Level Section 5-3 ct1 Hea
Page 205 and 206:
Operation Level Section 5-3 lcr1 Le
Page 207 and 208:
Operation Level Section 5-3 r-s RUN
Page 209 and 210:
Operation Level Section 5-3 al1h Al
Page 211 and 212:
Operation Level Section 5-3 See ■
Page 213 and 214:
Adjustment Level Section 5-4 Adjust
Page 215 and 216:
Adjustment Level Section 5-4 cmwt C
Page 217 and 218:
Adjustment Level Section 5-4 See
Page 219 and 220:
Page 221 and 222:
Page 223 and 224:
Adjustment Level Section 5-4 c-sc C
Page 225 and 226:
Adjustment Level Section 5-4 soak S
Page 227 and 228:
Adjustment Level Section 5-4 sprt S
Page 229 and 230:
Adjustment Level Section 5-4 db Pos
Page 231 and 232:
Bank Setting Level Section 5-5 5-5
Page 233 and 234:
Bank Setting Level Section 5-5 See
Page 235 and 236:
Bank Setting Level Section 5-5 Sett
Page 237 and 238:
Bank Setting Level Section 5-5 *.so
Page 239 and 240:
PID Setting Level Section 5-6 *.p P
Page 241 and 242:
PID Setting Level Section 5-6 *.csc
Page 243 and 244:
Manual Control Level Section 5-8 5-
Page 245 and 246:
Initial Setting Level Section 5-9 5
Page 247 and 248:
Initial Setting Level Section 5-9 S
Page 249 and 250:
Initial Setting Level Section 5-9 s
Page 251 and 252: Initial Setting Level Section 5-9 S
Page 253 and 254: Initial Setting Level Section 5-9 o
Page 255 and 256: Initial Setting Level Section 5-9 a
Page 257 and 258: Initial Setting Level Section 5-9 t
Page 263 and 264: Initial Setting Level Section 5-9 a
Page 265 and 266: Advanced Function Setting Level Sec
Page 301: Advanced Function Setting Level Sec
Page 305 and 306: This section describes how the user
Page 307 and 308: User Calibration Section 6-2 6-2 Us
Page 309 and 310: Thermocouple Calibration (Thermocou
Page 311 and 312: Platinum Resistance Thermometer Cal
Page 313 and 314: Calibrating Analog Input (Analog In
Page 315 and 316: Calibrating the Transfer Output Sec
Page 317 and 318: Checking Indication Accuracy Sectio
Page 319 and 320: Specifications Ratings Appendix Sup
Page 321 and 322: Proportional band (P) Temperature I
Page 323 and 324: E54-CT3 40 × 40 30 30 12 dia. 9 Tw
Page 325 and 326: E58-CIFIR USB-Infrared Conversion C
Page 327 and 328: Appendix Action Control continues,
Page 329 and 330: Troubleshooting Appendix Checking P
Page 331 and 332: Symptom: Cannot Communicate or a Co
Page 333 and 334: Parameter Operation Lists Operation
Page 335 and 336: Proportional Band (See note 1.) Int
Page 337 and 338: Bank Setting Level Appendix Paramet
Page 339 and 340: PID Setting Level Appendix Paramete
Page 341 and 342: Scaling Upper Limit in-h Scaling lo
Page 343 and 344: Transfer Output Lower Limit Linear
Page 345 and 346: Auxiliary Output 1 Open in Alarm Au
Page 347 and 348: Control Output 1 Assignment out1 Wh
Page 349 and 350: Appendix Parameters Characters Sett
Page 351 and 352: Note (1) The parameters in the curr
Page 353 and 354:
Related initialized parameters Rela
Page 355 and 356:
Changed parameter Related initializ
Page 357 and 358:
Appendix Sensor Input Setting Range
Page 359 and 360:
(4) When the PF Setting parameter i
Page 361 and 362:
c l.adj M at AT Execute/Cancel off
Page 363 and 364:
Protect Level Press the O Key for a
Page 365 and 366:
Numerics 2-PID control, 51, 228 A a
Page 367 and 368:
L LBA (loop burnout alarm), 114 ban
Page 369 and 370:
MV display, 250 MV display selectio
Page 371 and 372:
U universal inputs, 284 up key, 4 U
Page 373:
Revision History A manual revision
Page 376:
OMRON ELECTRONICS LLC • THE AMERI
show all

E5CNH E5AN-H E5EN-H Digital Controllers User's Manual - OMRON

Create successful ePaper yourself

Delete template?

Save as template?