E5CNH E5AN-H E5EN-H Digital Controllers User's Manual - OMRON

More documents

Recommendations

Info

312 Appendix (2) Unless the Program Pattern parameter is set to OFF, the bank number will be from 0 to the value set for the Valid Program Bank parameter. Adjustment Level Parameters Characters Setting (monitor) value Display Default Unit Set value Adjustment Level Display l.adj AT Execute/Cancel at OFF: AT Cancel off, OFF None AT-2: 100%AT Execute at-2, AT-1: 40%AT Execute (See note 3.) at-1 Communications Writing cmwt OFF, ON off, on OFF None Infrared Communications Use irdr OFF, ON off, on OFF None SP Mode spmd LSP, RSP lsp, rsp LSP None Heater Current 1 Value Monitor ct1 0.0 to 55.0 A Heater Burnout Detection 1 hb1 0.0 to 50.0 0.0 A Heater Overcurrent Detection 1 oc1 0.0 to 50.0 50.0 A Heater Current 2 Value Monitor ct2 0.0 to 55.0 A Heater Burnout Detection 2 hb2 0.0 to 50.0 0.0 A Heater Overcurrent Detection 2 oc2 0.0 to 50.0 50.0 A Leakage Current 1 Monitor lcr1 0.0 to 55.0 A HS Alarm 1 hs1 0.0 to 50.0 50.0 A Leakage Current 2 Monitor lcr2 0.0 to 55.0 A HS Alarm 2 hs2 0.0 to 50.0 50.0 A Heater Burnout Detection 1 hb1 0.0 to 50.0 0.0 A Heater Burnout Detection 2 hb2 0.0 to 50.0 0.0 A SP 0 sp-0 SP lower limit to SP upper limit 0 EU SP 1 sp-1 SP lower limit to SP upper limit 0 EU SP 2 sp-2 SP lower limit to SP upper limit 0 EU SP 3 sp-3 SP lower limit to SP upper limit 0 EU Temperature Input Shift ins −199.99 to 32400 0.00 °C or °F Upper Limit Temperature Input Shift Value insh −199.99 to 32400 0.00 °C or °F Lower Limit Temperature Input Shift Value insl −199.99 to 32400 0.00 °C or °F
Proportional Band (See note 1.) Integral Time (See note 1.) Derivative Time (See note 1.) Cooling Coefficient (See note 1.) p Universal input: 0.1 to 3240.0 8.0 °C or °F (See note 1.) Analog input: 0.1 to 999.9 10.0 %FS i Standard, heating/cooling, position proportional (closed): 0.0 to 3240.0 Position proportional (floating): 0.1 to 3240.0 233.0 Second d 0.0 to 3240.0 40.0 Second 0.0 to 3240.0 40.0 Second c-sc 0.01 to 99.99 1.00 None Dead Band c-db Temperature input: −1999.9 to 3240.0 0.0 °C or °F Analog input: −19.99 to 99.99 0.00 %FS <strong>Manual</strong> Reset Value of-r 0.0 to 100.0 50.0 % Hysteresis (Heating) hys Temperature input: 0.1 to 3240.0 1.0 °C or °F Analog input: 0.01 to 99.99 0.10 %FS Hysteresis (Cooling) chys Temperature input: 0.1 to 3240.0 1.0 °C or °F Analog input: 0.01 to 99.99 0.10 %FS Soak Time (See note 2.) soak 1 to 9,999 1 min or h Wait Band (See note 2.) wt-b Temperature input: OFF, 0.1 to 3240.0 Analog input: OFF, 0.01 to 99.99 MV at Stop mv-5 Standard: −5.0 to 105.0 Heating/cooling: −105.0 to 105.0 Position proportional (Floating or Direct Setting of Position Proportional MV parameter set to OFF): CLOS, HOLD, OPEN Position proportional (Close and Direct Setting of Position Proportional MV parameter set to ON): −5.0 to 105.0 MV at PV Error mv-e Standard: −5.0 to 105.0 Heating/cooling: −105.0 to 105.0 Position proportional (Floating or Direct Setting of Position Proportional MV parameter set to OFF): CLOS, HOLD, OPEN Position proportional (Close and Direct Setting of Position Proportional MV parameter set to ON): −5.0 to 105.0 off, 0.1 to 3240.0 off, 0.01 to 99.99 clos, hold, open clos, hold, open OFF °C or °F OFF %FS 0.0 % HOLD None 0.0 % 0.0 % HOLD None Appendix Parameters Characters Setting (monitor) value Display Default Unit Set value SP Ramp Set Value (See note 2.) sprt OFF or 1 to 9,999 off, 1 to 9999 0.0 % OFF EU/s, EU/ min, EU/h 313
Page 1:
SUB1 SUB2 SUB3 HA OUT1 STOP OUT2 CW
Page 5 and 6:
Preface The E5CN-H, E5AN-H, and E5E
Page 7 and 8:
Disclaimers CHANGE IN SPECIFICATION
Page 9 and 10:
■ Safety Precautions CAUTION Do n
Page 11 and 12:
Precautions for Safe Use Be sure to
Page 13 and 14:
● Ensuring Measurement Accuracy W
Page 15 and 16:
Power supply ● Ferrite Core Conne
Page 17 and 18:
Conventions Used in This Manual Mea
Page 19 and 20:
TABLE OF CONTENTS SECTION 1 Introdu
Page 21 and 22:
About this Manual: This manual desc
Page 23 and 24:
SECTION 1 Introduction This section
Page 25 and 26:
Names of Parts Section 1-1 E5EN-H 1
Page 27 and 28:
I/O Configuration and Main Function
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Setting Level Configuration and Key
Page 35 and 36:
Setting Level Configuration and Key
Page 37 and 38:
Communications Function Section 1-4
Page 39 and 40:
SECTION 2 Preparations This section
Page 41 and 42:
Installation Section 2-1 2-1-2 Pane
Page 43 and 44:
Installation Section 2-1 2-1-3 Moun
Page 45 and 46:
Installation Section 2-1 Mounting t
Page 47 and 48:
Installation Section 2-1 E5AN/EN-H
Page 49 and 50:
Installation Section 2-1 1,2,3... 1
Page 51 and 52:
Wiring Terminals Section 2-2 E5AN/E
Page 53 and 54:
Wiring Terminals Section 2-2 Contro
Page 55 and 56:
Wiring Terminals Section 2-2 Take c
Page 57 and 58:
Wiring Terminals Section 2-2 Take c
Page 59 and 60:
Wiring Terminals Section 2-2 CT Inp
Page 61 and 62:
Wiring Terminals Section 2-2 RS-232
Page 63 and 64:
Using the Support Software Port Sec
Page 65 and 66:
Using Infrared Communications Secti
Page 67 and 68:
SECTION 3 Basic Operation This sect
Page 69 and 70:
Initial Setting Examples Section 3-
Page 71 and 72:
Setting the Input Type Section 3-2
Page 73 and 74:
Selecting the Temperature Unit Sect
Page 75 and 76:
Setting Output Specifications Secti
Page 77 and 78:
Setting Output Specifications Secti
Page 79 and 80:
Using ON/OFF Control Section 3-7 To
Page 81 and 82:
Using ON/OFF Control Section 3-7 In
Page 83 and 84:
Determining PID Constants (AT, ST,
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Alarm Outputs Section 3-9 2.d 45.0
Page 91 and 92:
Alarm Outputs Section 3-9 3-9-2 Ala
Page 93 and 94:
Using Heater Burnout, Heater Short,
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Setting the No. 3 Display Section 3
Page 107 and 108:
SECTION 4 Applications Operations T
Page 109 and 110:
Shifting Input Values Section 4-1 4
Page 111 and 112:
Shifting Input Values Section 4-1 F
Page 113 and 114:
Alarm Hysteresis Section 4-2 For ex
Page 115 and 116:
Executing Heating/Cooling Control S
Page 117 and 118:
Executing Heating/Cooling Control S
Page 119 and 120:
Using Event Inputs Section 4-5 Cont
Page 121 and 122:
Using Event Inputs Section 4-5 Cont
Page 123 and 124:
Setting the SP Upper and Lower Limi
Page 125 and 126:
Using the SP Ramp Function to Limit
Page 127 and 128:
Moving to the Advanced Function Set
Page 129 and 130:
Using the Key Protect Level Section
Page 131 and 132:
PV Change Color Section 4-10 4-10 P
Page 133 and 134:
PV Change Color Section 4-10 colr r
Page 135 and 136:
Alarm Delays Section 4-11 Note (1)
Page 137 and 138:
Loop Burnout Alarm Section 4-12 Par
Page 139 and 140:
Loop Burnout Alarm Section 4-12 Ini
Page 141 and 142:
Performing Manual Control Section 4
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Using the Transfer Output Section 4
Page 149 and 150:
Using the Transfer Output Section 4
Page 151 and 152:
Using Banks and PID Sets Section 4-
Page 153 and 154:
Using Banks and PID Sets Section 4-
Page 155 and 156:
Using the Simple Program Function S
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Output Adjustment Functions Section
Page 165 and 166:
Output Adjustment Functions Section
Page 167 and 168:
Using the Extraction of Square Root
Page 169 and 170:
Setting the Width of MV Variation S
Page 171 and 172:
Setting the PF Key Section 4-20 Set
Page 173 and 174:
Counting Control Output ON/OFF Oper
Page 175 and 176:
Displaying PV/SV Status Section 4-2
Page 177 and 178:
Using a Remote SP Section 4-23 4-23
Page 179 and 180:
Position-proportional Control Secti
Page 181 and 182:
Logic Operations Section 4-25 Manua
Page 183 and 184:
Logic Operations Section 4-25 Examp
Page 185 and 186:
Logic Operations Section 4-25 4. Se
Page 187 and 188:
Logic Operations Section 4-25 11. C
Page 189 and 190:
Logic Operations Section 4-25 Opera
Page 191 and 192:
This section describes the individu
Page 193 and 194:
Protect Level Section 5-2 5-2 Prote
Page 195 and 196:
Protect Level Section 5-2 wtpt Sett
Page 197 and 198:
Operation Level Section 5-3 5-3 Ope
Page 199 and 200:
Operation Level Section 5-3 Functio
Page 201 and 202:
Operation Level Section 5-3 bank Ba
Page 203 and 204:
Operation Level Section 5-3 ct1 Hea
Page 205 and 206:
Operation Level Section 5-3 lcr1 Le
Page 207 and 208:
Operation Level Section 5-3 r-s RUN
Page 209 and 210:
Operation Level Section 5-3 al1h Al
Page 211 and 212:
Operation Level Section 5-3 See ■
Page 213 and 214:
Adjustment Level Section 5-4 Adjust
Page 215 and 216:
Adjustment Level Section 5-4 cmwt C
Page 217 and 218:
Adjustment Level Section 5-4 See
Page 219 and 220:
Page 221 and 222:
Page 223 and 224:
Adjustment Level Section 5-4 c-sc C
Page 225 and 226:
Adjustment Level Section 5-4 soak S
Page 227 and 228:
Adjustment Level Section 5-4 sprt S
Page 229 and 230:
Adjustment Level Section 5-4 db Pos
Page 231 and 232:
Bank Setting Level Section 5-5 5-5
Page 233 and 234:
Bank Setting Level Section 5-5 See
Page 235 and 236:
Bank Setting Level Section 5-5 Sett
Page 237 and 238:
Bank Setting Level Section 5-5 *.so
Page 239 and 240:
PID Setting Level Section 5-6 *.p P
Page 241 and 242:
PID Setting Level Section 5-6 *.csc
Page 243 and 244:
Manual Control Level Section 5-8 5-
Page 245 and 246:
Initial Setting Level Section 5-9 5
Page 247 and 248:
Initial Setting Level Section 5-9 S
Page 249 and 250:
Initial Setting Level Section 5-9 s
Page 251 and 252:
Page 253 and 254:
Initial Setting Level Section 5-9 o
Page 255 and 256:
Initial Setting Level Section 5-9 a
Page 257 and 258:
Initial Setting Level Section 5-9 t
Page 259 and 260:
Page 261 and 262:
Page 263 and 264:
Initial Setting Level Section 5-9 a
Page 265 and 266:
Advanced Function Setting Level Sec
Page 267 and 268:
Page 269 and 270:
Page 271 and 272:
Page 273 and 274:
Page 275 and 276:
Page 277 and 278:
Page 279 and 280:
Page 281 and 282:
Page 283 and 284: Advanced Function Setting Level Sec
Page 303 and 304: Communications Setting Level Sectio
Page 305 and 306: This section describes how the user
Page 307 and 308: User Calibration Section 6-2 6-2 Us
Page 309 and 310: Thermocouple Calibration (Thermocou
Page 311 and 312: Platinum Resistance Thermometer Cal
Page 313 and 314: Calibrating Analog Input (Analog In
Page 315 and 316: Calibrating the Transfer Output Sec
Page 317 and 318: Checking Indication Accuracy Sectio
Page 319 and 320: Specifications Ratings Appendix Sup
Page 321 and 322: Proportional band (P) Temperature I
Page 323 and 324: E54-CT3 40 × 40 30 30 12 dia. 9 Tw
Page 325 and 326: E58-CIFIR USB-Infrared Conversion C
Page 327 and 328: Appendix Action Control continues,
Page 329 and 330: Troubleshooting Appendix Checking P
Page 331 and 332: Symptom: Cannot Communicate or a Co
Page 333: Parameter Operation Lists Operation
Page 337 and 338: Bank Setting Level Appendix Paramet
Page 339 and 340: PID Setting Level Appendix Paramete
Page 341 and 342: Scaling Upper Limit in-h Scaling lo
Page 343 and 344: Transfer Output Lower Limit Linear
Page 345 and 346: Auxiliary Output 1 Open in Alarm Au
Page 347 and 348: Control Output 1 Assignment out1 Wh
Page 349 and 350: Appendix Parameters Characters Sett
Page 351 and 352: Note (1) The parameters in the curr
Page 353 and 354: Related initialized parameters Rela
Page 355 and 356: Changed parameter Related initializ
Page 357 and 358: Appendix Sensor Input Setting Range
Page 359 and 360: (4) When the PF Setting parameter i
Page 361 and 362: c l.adj M at AT Execute/Cancel off
Page 363 and 364: Protect Level Press the O Key for a
Page 365 and 366: Numerics 2-PID control, 51, 228 A a
Page 367 and 368: L LBA (loop burnout alarm), 114 ban
Page 369 and 370: MV display, 250 MV display selectio
Page 371 and 372: U universal inputs, 284 up key, 4 U
Page 373: Revision History A manual revision
Page 376: OMRON ELECTRONICS LLC • THE AMERI
show all

E5CNH E5AN-H E5EN-H Digital Controllers User's Manual - OMRON

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?