E5CNH E5AN-H E5EN-H Digital Controllers User's Manual - OMRON

340
pmov
0
M
oapt
0
M
icpt
0
M
wtpt
off
M
Protect Level
The time taken to move to the protect level
can be adjusted by changing the "Move to
protect level time" setting.
Move to Protect Level:
Displayed only when a password
is set. Restricts moving to protect
level.
Operation/Adjustment Protect:
Restricts displaying and
modifying menus in operation,
adjustment, and manual
control levels.
Initial Setting/
Communications Protect:
This protect level restricts movement
to the initial setting, communications
setting, and advanced
function setting levels.
Setting Change Protect:
Protects changes to setups
by operating the front panel
keys.
pfpt PF Key Protect
Restricts PF key operation
off (E5AN/EN-H only)
M
Parameter Mask Enable:
pmsk Displayed only when a
on parameter mask is set.
M
Password to Move to
prlp Protect Level:
0 Password setting
M
Press the O Key for at least 1 s.
Press the O Key for at least 3 s.
Other than the Auto/Manual Switch display
Press the O Key less than 1 s.
Communications
Setting Level
Displayed only for models with communications. Changes
are effective after cycling power or after a software reset.
Protocol Setting:
psel Switches between
CompoWay/F (SYScwf
WAY) and Modbus.
M
u-no Communications Unit No.
1
M
bps
9.6
M
len 7
M
Communications
sbit Stop Bits
2
M
prty
even
M
sdwt
20
M
Communications
Baud Rate
CompoWay/F
(SYSWAY) only
Communications
Data Length
Communications Parity
Send Data Wait Time
Initial Setting Level
Press the O Key less than 1 s.
in-t
5
M
in-h
100
M
in-l
0
M
dp
0
M
d-u c
M
c sl-h
1300.0
M
sl-l SP Lower Limit
-200.0
M
cntl PID ON/OFF
pid
M
Standard or
s-hc Heating/Cooling
stnd
M
ST (Self-tuning)
st
on
M
c
ptrn
off
M
pbnk
7
M
cp
20
M
c-cp
20
M
orev
or-r
M
alt1
2
M
c
alh1 Alarm 1
Hysteresis
0.2
M
Input Type
Scaling Upper Limit
Scaling Lower Limit
Decimal Point
For input type of analog
Temperature Unit
°C, °F
For input type of
temperature
SP Upper Limit
Limit the set point
For input type of
temperature, standard
control, or PID
Program Pattern
Valid Program Bank
When assigning PID or
control output to ON/OFF
output
Control Period (Heating)
Set the ON/OFF
output cycle.
Control Period (Cooling)
Direct/Reverse Operation
Alarm 1 Type
alt2 Alarm 2 Type
2
M
Alarm 2
alh2
Hysteresis
0.2
M
Alarm 3 Type
alt3
2
M
Alarm 3
alh3
Hysteresis
0.2
c
c
M
tr-t
off
M
tr-h Transfer Output
Upper Limit
100.0
M
tr-l Transfer Output
Lower Limit
0.0
M
Linear Current Output
o1-t
4-20
Linear output
M
ev-b
1
M
ev-1
none
M
ev-2
stop
M
ev-3
Event Input
Assignment 3
none
M
ev-4
Event Input
Assignment 4
none
M
clfl
flot
M
Transfer Output Type
Linear output
Bank Numbers Used
Event Input
Assignment 1
Event Input
Assignment 2
Closed/Floating
calb Motor Calibration
off
M
mot Travel Time
30
M
sqr Extraction of Square
Root Enable
off
M
Move to Advanced Function
Setting Level:
amov Displayed when initial set-
0 ting/ communications protect
is set to 0.
M
Move by setting password (−169).
Appendix