SV-iS7 User Manual - Inverter Drive Supermarket

More documents

Recommendations

Info

Chapter 9 Monitor Functions The detected frequency width is set as follows and the illustration below shows the frequency width having been set at 10Hz. 2 : FDT-2 Group Code No. Function Display Initial Setting Unit OUT 58 FDT Band (Hz) - 10.00 Hz Active when the frequency set by the user is equal to the FDT Frequency and the No. 0 FDT-1 condition above is simultaneously met. [absolute value(set frequency – detected frequency) < detected frequency width /2 ] & [ FDT-1 ] This case assumes that the detected frequency width is 10Hz and the detected frequency is 30Hz. 3 : FDT-3 Group OUT Code No. 57 Set Frequency 15Hz Frequency Q1 Operating command Function Display FDT Frequency Initial Setting Unit - 30.00 Hz 58 FDT Band (Hz) - 10.00 Hz Set Frequency Frequency Q1 Operating command 20Hz 25Hz 20Hz 30Hz Active when the operating frequency meets the following condition. 40Hz 40Hz 50Hz 35Hz absolute value(detected frequency – operating frequency) < detected frequency width /2 9-11
Chapter 9 Monitor Functions 4 : FDT-4 9-12 Group Code No. Function Display Initial Setting Unit OUT 57 FDT Frequency - 30.00 Hz 58 FDT Band (Hz) - 10.00 Hz Can operate setting the conditions of acceleration and deceleration at the same time. Acceleration : operating frequency >= detected frequency Deceleration : operating frequency > (detected frequency - detected frequency/2) Group Code No. Function Display Initial Setting Unit OUT 57 58 FDT Frequency FDT Band (Hz) - - 30.00 10.00 Hz Hz 5 : Over Load (motor overload) Active when the motor is given overload. 6 : IOL (inverter overload) Active in case of a failure for inverse time characteristic protection against inverter overload. 7 : Under Load (underload warning) Active in case of underload warning. 8 : Fan Warning (fan failure) Set ‘8: Fan Warning’ at multi-function output and it will be Activated when there is a problem with the cooling fan. 9 : Stall (motor stall) Frequency Q1 Operating command Frequency Q1 Operating command 30Hz 30Hz Active in case of a stall caused by the motor overload. 35Hz 25Hz 25Hz
Page 1 and 2:
Right choice for ultimate yield LSI
Page 3 and 4:
ii WARNING � Do not remove the co
Page 5 and 6:
iv Environment (2) Wiring Ambient t
Page 7 and 8:
Introduction to the Manual Introduc
Page 9 and 10:
ii Contents 3.1.2 3.1.3 3.1.4 3.1.5
Page 11 and 12:
Contents iv Chapter 7 Basic Functio
Page 13 and 14:
Contents vi 8.1.24 Cooling fan cont
Page 15 and 16:
Contents viii Chapter 11 Communicat
Page 17 and 18:
x Contents 13.1.11 Parameter mode -
Page 19 and 20:
Chapter 1 Basics 1-2 1.1.5 Distribu
Page 21 and 22:
Chapter 2 Specifications 2-1 2.1 Sp
Page 23 and 24:
Chapter 2 Specifications 2) Operati
Page 25 and 26:
Chapter 3 Installation Note 3-2 Cau
Page 27 and 28:
Chapter 3 Installation 3) SV0110-01
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Chapter 3 Installation 3-10 2) SV00
Page 35 and 36:
Page 37 and 38:
Chapter 3 Installation 3.1.5 Dimens
Page 39 and 40:
Chapter 3 Installation 2) Mounting
Page 41 and 42:
4.1 Wiring 4.1.1 How to separate fr
Page 43 and 44:
4.1.2 How to separate front cover w
Page 45 and 46:
3) How to set EMC Filter functions
Page 47 and 48:
4.1.6 Terminal wiring diagram (POWE
Page 49 and 50:
3) 90 ~ 160 kW (400V) R(L1) S(L2) T
Page 51 and 52:
4.1.9 Control terminal line diagram
Page 53 and 54:
1) Example of Distribution Relay2 (
Page 55 and 56:
Input signal Output Signal 4.1.11 C
Page 57 and 58:
4.2 Operation Checking Chapter 4 Wi
Page 59 and 60:
5.1 Peripheral Devices Ground 5.1.1
Page 61 and 62:
2) AC Reactor Specifications INVERT
Page 63 and 64:
4) Dimensions - Group 1 - Group 2 5
Page 65 and 66:
6.1 How to Use Keypad 6.1.1 Standar
Page 67 and 68:
3) Composition of Display (1) Monit
Page 69 and 70:
No Function Display Description FWD
Page 71 and 72:
Chapter 6 How to Use Keypad 1) Para
Page 73 and 74:
2) Mode Shift with User/Macro Mode
Page 75 and 76:
PAR PRT N STP 0.00Hz 00 Jump Code 4
Page 77 and 78:
2) Code shift (function Items) in o
Page 79 and 80:
6.1.6 Parameter setting 1) Paramete
Page 81 and 82:
6.1.7 Operating status monitoring 1
Page 83 and 84:
3) How to use status display Chapte
Page 85 and 86:
3) Saving and monitoring of failure
Page 87 and 88:
7.1 Basic Functions 7.1.1 How to se
Page 89 and 90:
Chapter 7 Basic Functions IN-05 V1
Page 91 and 92:
The output frequency of bipolar vol
Page 93 and 94:
Chapter 7 Basic Functions 5) Freque
Page 95 and 96:
Chapter 7 Basic Functions If you se
Page 97 and 98:
[Example of speed-8] Chapter 7 Basi
Page 99 and 100:
Chapter 7 Basic Functions 4) Operat
Page 101 and 102:
7.1.8 Run immediately with power On
Page 103 and 104:
Caution Chapter 7 Basic Functions 9
Page 105 and 106:
Chapter 7 Basic Functions You can c
Page 107 and 108:
7.1.12 Acc/Dec Stop command Group C
Page 109 and 110:
Chapter 7 Basic Functions The user
Page 111 and 112:
Chapter 7 Basic Functions 7.1.16 Se
Page 113 and 114:
Frequency Voltage Current Operating
Page 115 and 116:
Chapter 7 Basic Functions (1) ADV-2
Page 117 and 118:
7.1.21 Multi-function input termina
Page 119 and 120:
Chapter 8 Applied Functions 8-2 Set
Page 121 and 122:
Chapter 8 Applied Functions If 10.4
Page 123 and 124:
Chapter 8 Applied Functions 8.1.3 U
Page 125 and 126:
Chapter 8 Applied Functions 8.1.5 S
Page 127 and 128:
Chapter 8 Applied Functions * Accel
Page 129 and 130:
Chapter 8 Applied Functions 8.1.8 P
Page 131 and 132:
Chapter 8 Applied Functions For exa
Page 133 and 134:
Chapter 8 Applied Functions 4) PID
Page 135 and 136:
Chapter 8 Applied Functions 8-18 In
Page 137 and 138:
Chapter 8 Applied Functions APO-05
Page 139 and 140: Chapter 8 Applied Functions BAS-15
Page 141 and 142: Chapter 8 Applied Functions Before
Page 143 and 144: Chapter 8 Applied Functions lower O
Page 145 and 146: Chapter 8 Applied Functions 1) Prep
Page 147 and 148: Chapter 8 Applied Functions CON-48
Page 149 and 150: Chapter 8 Applied Functions Group C
Page 151 and 152: Chapter 8 Applied Functions If the
Page 153 and 154: Chapter 8 Applied Functions 8.1.19
Page 155 and 156: Chapter 8 Applied Functions ADV-61
Page 157 and 158: Chapter 8 Applied Functions The car
Page 159 and 160: Chapter 8 Applied Functions 8-42 Co
Page 163 and 164: Chapter 8 Applied Functions 8-46 Ca
Page 165 and 166: Chapter 8 Applied Functions 2) How
Page 167 and 168: Chapter 8 Applied Functions CNF-42
Page 169 and 170: Chapter 8 Applied Functions AUT-01
Page 175 and 176: Chapter 8 Applied Functions APO-41
Page 177 and 178: Chapter 8 Applied Functions 3) Inte
Page 179 and 180: Chapter 8 Applied Functions ADV-75
Page 181 and 182: Chapter 9 Monitor Functions 9-2 Set
Page 183 and 184: Chapter 9 Monitor Functions * Warni
Page 185 and 186: Chapter 9 Monitor Functions 2) Fail
Page 187 and 188: Chapter 9 Monitor Functions 9-8 Set
Page 189: Chapter 9 Monitor Functions 9.1.4 S
Page 193 and 194: Chapter 9 Monitor Functions Functio
Page 195 and 196: Chapter 9 Monitor Functions 9.1.5 F
Page 197 and 198: Chapter 9 Monitor Functions CNF-71
Page 199 and 200: Chapter 10 Protective Functions PRT
Page 201 and 202: Chapter 10 Protective Functions PRT
Page 203 and 204: 10.1.4 Motor overheat sensor input
Page 205 and 206: Setting Items Functions bit2 bit1 O
Page 207 and 208: 1) Speed Command Loss Chapter 10 Pr
Page 209 and 210: T _ dec Example 1) % ED = × 100[%]
Page 211 and 212: 10.1.12 Speed variation failure Thi
Page 213 and 214: 10.1.19 Detection of motor not conn
Page 215 and 216: Category Loader Display Description
Page 217 and 218: Chapter 11 Communication Function 1
Page 221 and 222: Chapter 11 Communication Function C
Page 227 and 228: Chapter 11 Communication Function M
Page 229 and 230: Chapter 11 Communication Function F
Page 233 and 234: Chapter 11 Communication Function A
Page 241 and 242:
Chapter 11 Communication Function 2
Page 243 and 244:
Chapter 11 Communication Function A
Page 245 and 246:
Chapter 12 Checking and Troubleshoo
Page 247 and 248:
12.1.3 Troubleshooting Chapter 12 C
Page 249 and 250:
12.1.4 Replacement of cooling fan C
Page 251 and 252:
12.1.5 Daily and regular checkup li
Page 253 and 254:
Chapter 13 Table of Functions 13.1
Page 255 and 256:
Chapter 13 Table of Functions 13.1.
Page 257 and 258:
Chapter 13 Table of Functions 13-5
Page 259 and 260:
Page 261 and 262:
Chapter 13 Table of Functions Exten
Page 263 and 264:
Page 265 and 266:
Chapter 13 Table of Functions Contr
Page 267 and 268:
Chapter 13 Table of Functions Contr
Page 269 and 270:
Chapter 13 Table of Functions Input
Page 271 and 272:
Page 273 and 274:
Page 275 and 276:
Page 277 and 278:
Chapter 13 Table of Functions Commu
Page 279 and 280:
Chapter 13 Table of Functions 3.1.8
Page 281 and 282:
Chapter 13 Table of Functions No. 1
Page 283 and 284:
Page 285 and 286:
Page 287 and 288:
Chapter 13 Table of Functions No. C
Page 289 and 290:
Page 291 and 292:
Chapter 13 Table of Functions 3.1.1
Page 293 and 294:
Chapter 13 Table of Functions 13-41
Page 295 and 296:
ⅱ
Page 297 and 298:
��
Page 299:
Revision History No Date Edition Ve
show all

SV-iS7 User Manual - Inverter Drive Supermarket

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?