SV-iS7 User Manual - Inverter Drive Supermarket

No. Communic
ation No.
Function
Display
Name
Setting Range
Chapter 13 Table of Functions
Initial
Value
Shift
in
Oper
atio
n
Page V
/
F
Control Mode
52 0h1B34 Stall Level 1 stall level 1 30~250[%] 180 X 10-3 O O X O X
53 0h1B35 Stall Freq 2 stall frequency 2
stall frequency 1
~stall frequency 2[Hz]
60.00 O 10-3 O O X O X
54 0h1B36 Stall Level 2 stall level 2 30~250[%] 180 X 10-3 O O X O X
55 0h1B37 Stall Freq 3 stall frequency 3
stall frequency 2
~stall frequency 4[Hz]
60.00 O 10-3 O O X O X
56 0h1B38 Stall Level 3 stall level 3 30~250[%]
stall frequency 3
180 X 10-3 O O X O X
57 0h1B39 Stall Freq 4 stall frequency 4 ~maximum frequency
[Hz]
60.00 O 10-3 O O X O X
58 0h1B3A Stall Level 4 stall level 4 30~250[%] 180 X 10-3 O O X O X
66 0h1B42 DB Warn %ED
DB resistance
warning level
0~30[%] 0 O 10-11 O O O O O
70 0h1B46
Over SPD
Freq
overspeed
judgment
frequency
20~130[%] 120.0 O 10-13 X X O X O
72 0h1B48
Over SPD
Time
overspeed
judgment time
0.01~10.00[sec] 0.01 O 10-13 X X O X O
73 0h1B49
Speed Dev
Trip
speed error failure
0
1
No
Yes
0:No O 10-14 X X O X X
74 0h1B4A
Speed Dev
Band
speed error width
2~maximum
frequency[Hz]
20.00 O 10-14 X X O X X
75 0h1B4B
Speed Dev
Time
speed error
judgment time
0.1~1000.0[sec] 1.0 O 10-14 X X O X X
77 0h1B4D
Enc Wire
Check
Encoder option
connection check
0
1
No
Yes
0:No O 10-14 X X O X O
78 0h1B4E
Enc Check
Time
Encoder
connection check
time
0.1~1000.0[sec] 1.0 O 10-14 X X O X O
79 0h1B4F FAN Trip Mode
cooling fan failure
selection
0
1
Trip
Warning
0:Trip O 10-14 O O O O O
movement 0 None
80 0h1B50 Opt Trip Mode selection in case
of option trip
low voltage failure
1
2
Free-Run
Dec
1:Free-Run O 10-16 O O O O O
81 0h1B51 LVT Delay judgment delay
time
0~60.0[sec] 0.0 X 10-14 O O O O O
* The grey code refers to hidden code, emerging only in case of setting of the code.
Note 38)
PRT-10 codes are displayed only when PRT-09(Retry Number) is set above “0”.
Note 39)
PRT-13~15 codes are displayed only when PRT-12(Lost Cmd Mode) is not “NONE”.
Note 40)
PRT-32~33 codes are displayed only when PRT-31(No Motor Trip is set as “Free-Run”.
S
L
V
C
S
L
T
13-38
V
C
T