SV-iS7 User Manual - Inverter Drive Supermarket

Extended Function Group (PAR � ADV)
No. Communication
No.
Function
Display
Name Setting Range
Chapter 13 Table of Functions
Initial
Value
Shift in
Operation
Page V
/
F
Control Mode
24 0h1318 Freq Limit frequency limit
0
1
No
Yes
0:No X 7-29 O O O X X
25
Note10) 0h1319 Freq Limit Lo
frequency lower
limit
0~upper limit[Hz] 0.50 O 7-29 O O O X X
26 0h131A Freq Limit Hi
frequency upper
limit
0.5~maximum
frequency[Hz]
60.00 X 7-29 O O O X X
27 0h131B Jump Freq frequency jump
0
1
No
Yes
0:No X 7-29 O O O X X
28
Note 11) 0h131C Jump Lo 1
jump frequency
lower limit 1
0~jumpfrequencyupper
10.00
limit1[Hz]
Jump frequency lower
O 7-29 O O O X X
29 0h131D Jump Hi 1
jump frequency
upper limit 1
limit1
~maximum
frequency[Hz]
15.00 O 7-29 O O O X X
30 0h131E Jump Lo 2
jump frequency
lower limit 2
0~jumpfrequency
upper limit2[Hz]
Jump frequency lower
20.00 O 7-29 O O O X X
31 0h131F Jump Hi 2
jump frequency
upper limit 2
limit2
~maximum
frequency[Hz]
25.00 O 7-29 O O O X X
32 0h1320 Jump Lo 3
jump frequency
lower limit 3
0~jumpfrequency
upper limit3[Hz]
Jump frequency lower
30.00 O 7-29 O O O X X
33 0h1321 Jump Hi 3
jump frequency
upper limit 3
limit3
~maximum
frequency[Hz]
35.00 O 7-29 O O O X X
41
Note12) 0h1329 BR Rls Curr brake open current 0~180.0[%] 50.0 O 8-54 O O O X X
42 0h132A BR Rls Dly
brake open delay
time
0~10.00[sec] 1.00 X 8-54 O O O X X
44 0h132C
BR Rls Fwd brake open
Fr
forward frequency
0~maximum
frequency[Hz]
1.00 X 8-54 O O O X X
45 0h132D
BR Rls Rev brake open
Fr
reverse frequency
0~maximum
frequency[Hz]
1.00 X 8-54 O O O X X
46 0h132E BR Eng Dly
brake close delay
time
0~10[sec] 1.00 X 8-54 O O O X X
47 0h132F BR Eng Fr
brake close
frequency
0~maximum
frequency[Hz]
2.00 X 8-54 O O O X X
50 0h1332
energy saving
E-Save Mode
operation
0
1
2
None
Manual
Auto
0:None X 8-35 O O X X X
51
Note13) 0h1333 Energy Save
energy saving
amount
0~30[%] 0 O 8-35 O O O X X
60 0h133C
Acc/Dec time
Xcel Change
exchange
Fr
frequency
0~maximum
frequency[Hz]
0.00 X 7-18 O O O X X
* The grey code refers to hidden code, emerging only in case of setting of the code.
Note 10)
ADV-25~26 is displayed only when ADV-24 (Freq Limit) is set as “Freq Limit”.
Note 11)
ADV-28~33 is displayed only when ADV-27 (Jump Freq) set as “Yes”.
Note 12)
ADV-41~47 is displayed only when a code of OUT-31~33 is set as “BR Control”.
Note 13)
ADV-51 is displayed only when ADV-50 (E-Save Mode) is set as values other than “None”.
S
L
V
C
S
L
T
V
C
T
13-8