SV-iS7 User Manual - Inverter Drive Supermarket

More documents

Recommendations

Info

11.1.7 Virtual multi-function input setting Chapter 11 Communication Function Group Code No. Function Display Setting Display Unit COM 70~85 Virtual DI x 0 None - 86 Virt DI Status - - - COM-70~85: You can control multi-function input by communication (common area h0385: see Page 11-28). The function which is set will be operated at each bit after set the function at COM-70~85 and then set the bit which is set the function wanted to 1 at 0h0322. Note that it should be set DRV-06, CMD source as Run command source. Ex) If you want to send Fx command with controlling virtual multi-function input command area by Int485, Fx function is triggered if 0h0001 is inputted in the 0h0322 after COM-70 (Virtual DI 1) is set to FX. It works without relation to IN65~75 (Px Define) and impossible to overlap setting. You can check the status of virtual multi-function input at COM-86. 11.1.8 Caution in parameter setting for communication Group Code No. Function Display Setting Display Unit CNF 48 Parameter Save 0 1 -No- -Yes- - - Set the common area parameter or keypad parameter by communication, start the inverter. Turn off and then on the inverter, and the setting state goes back to the state before it was set by communication. If you select Yes at CNF48 Parameter Save, all the currently set values are saved in the inverter and will remain unchanged even if you turn off and on the unit. If you set 0h03E0 address at 0 by communication and then at 1, all the currently set parameter values are saved in the inverter and will remain unchanged even if you turn off and on the unit. However, if it is set at 1 and you switch it to 0, it’s not effective. 11.1.9 Communication frame monitoring. You can easily check the state (normal, CRC/Checksum error, other errors, etc.) of the communication frame being received from the master by using the digital loader. Group Code No. Function Display Setting Display Unit COM 90 Comm Mon Sel 0 Int 485 - 91 Rcv Frame Num - - - 92 Err Frame Num - - - 93 NAK Frame Num - - - 94 Comm Update 0 1 -No- -Yes- - 11-5
Chapter 11 Communication Function COM-90 Comm Mon Sel: selects the communication channel to monitor. COM-91 Rcv Frame Num: counts the number of communication frames received normally from the master. COM-92 Err Frame Num: counts the number of CRC errors in the case of Modbus-RTU and Checksum errors in the case of LS Inv 485. COM-93 NAK Frame Num: counts the number of errors (communication address error, data range error, writing prohibition error) in the communication frames received from the master. COM-94 Comm Update: reconnect the communication after change of the initial status parameter as communication speed (baud rate) etc,. 11.1.10 Special communication area setting 11-6 Entire iS7 communication memory map Communication Area Memory Map Description Common iS5 compatible communication area Parameter registration type area Common iS7 communication area 0h0000 ~ 0h00FF Area compatible with iS5 0h0100 ~ 0h01FF Area registered in COM31~38, COM51~58 0h0200 ~ 0h023F Area registered in User Group 0h0240 ~ 0h027F Area registered in Macro Group 0h0280 ~ 0h02FF Reserved 0h0300 ~ 0h037F Inverter monitoring area 0h0380 ~ 0h03DF Inverter control area 0h03E0 ~ 0h03FF Inverter memory control area 0h0400 ~ 0h0FFF Reserved 0h1100 DRV Grp 0h1200 BAS Grp 0h1300 ADV Grp 0h1400 CON Grp 0h1500 IN Grp 0h1600 OUT Grp 0h1700 COM Grp 0h1800 APP Grp 0h1900 AUT Grp 0h1A00 APO Grp 0h1B00 PRT Grp 0h1C00 M2 Grp
Page 1 and 2:
Right choice for ultimate yield LSI
Page 3 and 4:
ii WARNING � Do not remove the co
Page 5 and 6:
iv Environment (2) Wiring Ambient t
Page 7 and 8:
Introduction to the Manual Introduc
Page 9 and 10:
ii Contents 3.1.2 3.1.3 3.1.4 3.1.5
Page 11 and 12:
Contents iv Chapter 7 Basic Functio
Page 13 and 14:
Contents vi 8.1.24 Cooling fan cont
Page 15 and 16:
Contents viii Chapter 11 Communicat
Page 17 and 18:
x Contents 13.1.11 Parameter mode -
Page 19 and 20:
Chapter 1 Basics 1-2 1.1.5 Distribu
Page 21 and 22:
Chapter 2 Specifications 2-1 2.1 Sp
Page 23 and 24:
Chapter 2 Specifications 2) Operati
Page 25 and 26:
Chapter 3 Installation Note 3-2 Cau
Page 27 and 28:
Chapter 3 Installation 3) SV0110-01
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Chapter 3 Installation 3-10 2) SV00
Page 35 and 36:
Page 37 and 38:
Chapter 3 Installation 3.1.5 Dimens
Page 39 and 40:
Chapter 3 Installation 2) Mounting
Page 41 and 42:
4.1 Wiring 4.1.1 How to separate fr
Page 43 and 44:
4.1.2 How to separate front cover w
Page 45 and 46:
3) How to set EMC Filter functions
Page 47 and 48:
4.1.6 Terminal wiring diagram (POWE
Page 49 and 50:
3) 90 ~ 160 kW (400V) R(L1) S(L2) T
Page 51 and 52:
4.1.9 Control terminal line diagram
Page 53 and 54:
1) Example of Distribution Relay2 (
Page 55 and 56:
Input signal Output Signal 4.1.11 C
Page 57 and 58:
4.2 Operation Checking Chapter 4 Wi
Page 59 and 60:
5.1 Peripheral Devices Ground 5.1.1
Page 61 and 62:
2) AC Reactor Specifications INVERT
Page 63 and 64:
4) Dimensions - Group 1 - Group 2 5
Page 65 and 66:
6.1 How to Use Keypad 6.1.1 Standar
Page 67 and 68:
3) Composition of Display (1) Monit
Page 69 and 70:
No Function Display Description FWD
Page 71 and 72:
Chapter 6 How to Use Keypad 1) Para
Page 73 and 74:
2) Mode Shift with User/Macro Mode
Page 75 and 76:
PAR PRT N STP 0.00Hz 00 Jump Code 4
Page 77 and 78:
2) Code shift (function Items) in o
Page 79 and 80:
6.1.6 Parameter setting 1) Paramete
Page 81 and 82:
6.1.7 Operating status monitoring 1
Page 83 and 84:
3) How to use status display Chapte
Page 85 and 86:
3) Saving and monitoring of failure
Page 87 and 88:
7.1 Basic Functions 7.1.1 How to se
Page 89 and 90:
Chapter 7 Basic Functions IN-05 V1
Page 91 and 92:
The output frequency of bipolar vol
Page 93 and 94:
Chapter 7 Basic Functions 5) Freque
Page 95 and 96:
Chapter 7 Basic Functions If you se
Page 97 and 98:
[Example of speed-8] Chapter 7 Basi
Page 99 and 100:
Chapter 7 Basic Functions 4) Operat
Page 101 and 102:
7.1.8 Run immediately with power On
Page 103 and 104:
Caution Chapter 7 Basic Functions 9
Page 105 and 106:
Chapter 7 Basic Functions You can c
Page 107 and 108:
7.1.12 Acc/Dec Stop command Group C
Page 109 and 110:
Chapter 7 Basic Functions The user
Page 111 and 112:
Chapter 7 Basic Functions 7.1.16 Se
Page 113 and 114:
Frequency Voltage Current Operating
Page 115 and 116:
Chapter 7 Basic Functions (1) ADV-2
Page 117 and 118:
7.1.21 Multi-function input termina
Page 119 and 120:
Chapter 8 Applied Functions 8-2 Set
Page 121 and 122:
Chapter 8 Applied Functions If 10.4
Page 123 and 124:
Chapter 8 Applied Functions 8.1.3 U
Page 125 and 126:
Chapter 8 Applied Functions 8.1.5 S
Page 127 and 128:
Chapter 8 Applied Functions * Accel
Page 129 and 130:
Chapter 8 Applied Functions 8.1.8 P
Page 131 and 132:
Chapter 8 Applied Functions For exa
Page 133 and 134:
Chapter 8 Applied Functions 4) PID
Page 135 and 136:
Chapter 8 Applied Functions 8-18 In
Page 137 and 138:
Chapter 8 Applied Functions APO-05
Page 139 and 140:
Chapter 8 Applied Functions BAS-15
Page 141 and 142:
Chapter 8 Applied Functions Before
Page 143 and 144:
Chapter 8 Applied Functions lower O
Page 145 and 146:
Chapter 8 Applied Functions 1) Prep
Page 147 and 148:
Chapter 8 Applied Functions CON-48
Page 149 and 150:
Chapter 8 Applied Functions Group C
Page 151 and 152:
Chapter 8 Applied Functions If the
Page 153 and 154:
Chapter 8 Applied Functions 8.1.19
Page 155 and 156:
Chapter 8 Applied Functions ADV-61
Page 157 and 158:
Chapter 8 Applied Functions The car
Page 159 and 160:
Chapter 8 Applied Functions 8-42 Co
Page 161 and 162:
Chapter 8 Applied Functions 8.1.25
Page 163 and 164:
Chapter 8 Applied Functions 8-46 Ca
Page 165 and 166:
Chapter 8 Applied Functions 2) How
Page 167 and 168:
Chapter 8 Applied Functions CNF-42
Page 169 and 170: Chapter 8 Applied Functions AUT-01
Page 171 and 172: Chapter 8 Applied Functions 8.1.37
Page 173 and 174: Chapter 8 Applied Functions 8.1.38
Page 175 and 176: Chapter 8 Applied Functions APO-41
Page 177 and 178: Chapter 8 Applied Functions 3) Inte
Page 179 and 180: Chapter 8 Applied Functions ADV-75
Page 181 and 182: Chapter 9 Monitor Functions 9-2 Set
Page 183 and 184: Chapter 9 Monitor Functions * Warni
Page 185 and 186: Chapter 9 Monitor Functions 2) Fail
Page 187 and 188: Chapter 9 Monitor Functions 9-8 Set
Page 189 and 190: Chapter 9 Monitor Functions 9.1.4 S
Page 191 and 192: Chapter 9 Monitor Functions 4 : FDT
Page 193 and 194: Chapter 9 Monitor Functions Functio
Page 195 and 196: Chapter 9 Monitor Functions 9.1.5 F
Page 197 and 198: Chapter 9 Monitor Functions CNF-71
Page 199 and 200: Chapter 10 Protective Functions PRT
Page 201 and 202: Chapter 10 Protective Functions PRT
Page 203 and 204: 10.1.4 Motor overheat sensor input
Page 205 and 206: Setting Items Functions bit2 bit1 O
Page 207 and 208: 1) Speed Command Loss Chapter 10 Pr
Page 209 and 210: T _ dec Example 1) % ED = × 100[%]
Page 211 and 212: 10.1.12 Speed variation failure Thi
Page 213 and 214: 10.1.19 Detection of motor not conn
Page 215 and 216: Category Loader Display Description
Page 217 and 218: Chapter 11 Communication Function 1
Page 219: Chapter 11 Communication Function 1
Page 227 and 228: Chapter 11 Communication Function M
Page 229 and 230: Chapter 11 Communication Function F
Page 233 and 234: Chapter 11 Communication Function A
Page 245 and 246: Chapter 12 Checking and Troubleshoo
Page 247 and 248: 12.1.3 Troubleshooting Chapter 12 C
Page 249 and 250: 12.1.4 Replacement of cooling fan C
Page 251 and 252: 12.1.5 Daily and regular checkup li
Page 253 and 254: Chapter 13 Table of Functions 13.1
Page 255 and 256: Chapter 13 Table of Functions 13.1.
Page 257 and 258: Chapter 13 Table of Functions 13-5
Page 261 and 262: Chapter 13 Table of Functions Exten
Page 265 and 266: Chapter 13 Table of Functions Contr
Page 267 and 268: Chapter 13 Table of Functions Contr
Page 269 and 270: Chapter 13 Table of Functions Input
Page 271 and 272:
Chapter 13 Table of Functions Input
Page 273 and 274:
Page 275 and 276:
Page 277 and 278:
Chapter 13 Table of Functions Commu
Page 279 and 280:
Chapter 13 Table of Functions 3.1.8
Page 281 and 282:
Chapter 13 Table of Functions No. 1
Page 283 and 284:
Page 285 and 286:
Chapter 13 Table of Functions 13.1.
Page 287 and 288:
Chapter 13 Table of Functions No. C
Page 289 and 290:
Page 291 and 292:
Chapter 13 Table of Functions 3.1.1
Page 293 and 294:
Chapter 13 Table of Functions 13-41
Page 295 and 296:
ⅱ
Page 297 and 298:
��
Page 299:
Revision History No Date Edition Ve
show all

SV-iS7 User Manual - Inverter Drive Supermarket

Create successful ePaper yourself

Delete template?

Save as template?