SV-iS7 User Manual - Inverter Drive Supermarket

Chapter 13 Table of Functions
13.1.3 Parameter mode – Parameter mode – Extended function group
(PAR�ADV)
Extended Function Group (PAR � ADV)
No.
13-7
Communi
cation
No.
Function Display Name Setting Range
Initial
Value
Shift
in
Oper
ation
Page V
/
F
Control Mode
00 - Jump Code jump code 0~99 24 O - O O O O O
01
02
0h1301
0h1302
Acc Pattern
Dec Pattern
accelerating pattern
decelerating pattern
0
1
Linear
S-curve
0:Linear
X
X
7-19
7-19
O
O
O
O
O
O
X
X
X
X
03 0h1303 Acc S Start
S accelerating starting
slope
1~100[%] 40 X 7-19 O O O X X
04 0h1304 Acc S End S accelerating end slope 1~100[%] 40 X 7-19 O O O X X
05 0h1305 Dec S Start
S decelerating starting
slope
1~100[%] 40 X 7-19 O O O X X
06 0h1306 Dec S End S decelerating end slope 1~100[%] 40 X 7-19 O O O X X
07 0h1307 Start Mode starting method
0
1
Acc
Dc-Start
0:Acc X 7-25 O O O X X
0 Dec
1 Dc-Brake
08 0h1308 Stop Mode stop method
2 Free-Run 0:Dec X 7-26 O O O X X
3 Flux Braking
4 Powr Braking
09 0h1309 Run Prevent
rotation preventing
direction selection
0
1
2
None
Forward Prev
Reverse Prev
0:Non
e
X 7-14 O O O X X
10 0h130A Power-on Run power input starting
0
1
No
Yes
0:No O 7-15 O O O X X
12
Note8) 0h130C Dc-Start Time starting DC braking time 0~60[sec] 0.00 X 7-25 O O O X X
13 0h130D Dc Inj Level DC supply 0~200[%] 50 X 7-25 O O O X X
14
Note9) 0h130E Dc-Block Time
Pre-DC braking output
block time
0~60[sec] 0.10 X 7-26 O O O X X
15 0h130F Dc-Brake Time DC braking time 0~60[sec] 1.00 X 7-26 O O O X X
16 0h1310 Dc-Brake Level DC braking 0~200[%] 50 X 7-26 O O O X X
17 0h1311 Dc-Brake Freq DC braking frequency
startingfrequency~
60[Hz]
5.00 X 7-26 O O O X X
20 0h1314 Acc Dwell Freq
Accelerating dwell
frequency
Starting frequency
~maximum
frequency[Hz]
5.00 X 8-9 O O O X X
21 0h1315 Acc Dwell Time
Accelerating dwell
operation time
0~60.0[sec] 0.00 X 8-9 O O O X X
22 0h1316 Dec Dwell Freq
Decelerating dwell
frequency
Starting frequency
~maximum
frequency[Hz]
5.00 X 8-9 O O O X X
23 0h1317 Dec Dwell Time
Decelerating dwell
operation time
0~60.0[sec] 0.00 X 8-9 O O O X X
* The grey code refers to hidden code, emerging only in case of setting of the code.
Note 8)
ADV-12 is displayed only when ADV-07 “Stop Mode” is set as “Dc-Start”.
Note 9)
ADV-14~17 is displayed only when ADV-08 “Stop Mode” is set as “DC-Brake”.
S
L
V
C
S
L
T
V
C
T