SV-iS7 User Manual - Inverter Drive Supermarket

More documents

Recommendations

Info

Applied Function Group (PAR � APP) No. Commu nication No. Function Display 21 0h1815 PID F/B Source Name Setting Range PID Feedback selection 0 V1 1 I1 2 V2 3 I2 4 Int 485 5 Encoder 6 FieldBus 7 PLC 8 Synchro 9 Binary Type Initial Value Chapter 13 Table of Functions Shift in Oper ation Page V / F Control Mode S L V C S L T 0:V1 X 8-12 O O O X X 22 0h1816 PID P-Gain PID proportional gain 0~1000[%] 50.0 O 8-12 O O O X X 23 0h1817 PID I-Time PID integral calculus time 0~200.0[sec] 10.0 O 8-12 O O O X X 24 0h1818 PID D-Time PID differential time 0~1000[msec] 0 O 8-12 O O O X X 25 0h1819 PID F-Gain PID Feed forward gain 0~1000.0[%] 0.0 O 8-12 O O O X X 26 0h181A P Gain Scale Proportional gain scale 0~100.0[%] 100.0 X 8-12 O O O X X 27 0h181B PID Out LPF PID output filter 0~10000[ms] PID lower limit 0 O 8-12 O O O X X 29 0h181D PID Limit Hi PID upper limit frequency frequency[Hz] ~300[Hz] 60.00 O 8-12 O O O X X 30 0h181E PID Limit Lo PID lower limit frequency -300 ~ PID upper limit frequency[Hz] -60 O 8-12 O O O X X 31 0h181F PID Out Inv PID output reversal 0 1 No Yes 0:No X 8-12 O O O X X 32 0h1820 PID Out Scale PID output scale 0.1~1000[%] 100.0 X 8-12 O O O X X 34 0h1822 Pre-PID Freq PID control period movement frequency 0~maximum frequency[Hz] 0.00 X 8-12 O O O X X 35 0h1823 Pre-PID Exit PID control period movement level 0~100[%] 0.0 X 8-12 O O O X X 36 0h1824 Pre-PID Delay PID control period movement delay time 0~9999[sec] 600 O 8-12 O O O X X 37 0h1825 PID Sleep DT PID sleep mode delay time 0~999.9[sec] 60.0 O 8-12 O O O X X 38 PID Sleep 0h1826 Freq PID Sleep mode frequency 0~maximum frequency[Hz] 0.00 O 8-12 O O O X X 39 PID WakeUp 0h1827 Lev PID Wake up level 0~100[%] 35 O 8-12 O O O X X 40 PID WakeUp 0h1828 Mod PID Wake up mode setting 0 1 2 Below Level Above Level Beyond Level 0:Below Level O 8-12 O O O X X 42 0h182A PID Unit Sel PID control period unit 0 % 0:% O 8-12 O O O X X selection 1 Bar 2 mBar 3 Pa 4 KPa 5 Hz 6 rpm 7 V 8 I 9 kW V C T 13-28
Chapter 13 Table of Functions No. 13-29 Commu nication No. Function Display Name Setting Range Initial Value Shift in Oper ation Page V / F Control Mode 10 HP 11 ℃ 12 ℉ 43 0h182B PID Unit Gain PID unit gain 0~300[%] 100.00 O 8-12 O O O X X 0 X 0.01 1 X 0.1 44 0h182C PID Unit Scale PID unit scale 2 X 1 2:x 1 O 8-12 O O O X X 3 X 0.1 4 X 0.01 45 0h182D PID P2-Gain PID 2 nd proportional gain 0~1000[%] 100.0 X 8-12 O O O X X S L V C S L T V C T
Page 1 and 2:
Right choice for ultimate yield LSI
Page 3 and 4:
ii WARNING � Do not remove the co
Page 5 and 6:
iv Environment (2) Wiring Ambient t
Page 7 and 8:
Introduction to the Manual Introduc
Page 9 and 10:
ii Contents 3.1.2 3.1.3 3.1.4 3.1.5
Page 11 and 12:
Contents iv Chapter 7 Basic Functio
Page 13 and 14:
Contents vi 8.1.24 Cooling fan cont
Page 15 and 16:
Contents viii Chapter 11 Communicat
Page 17 and 18:
x Contents 13.1.11 Parameter mode -
Page 19 and 20:
Chapter 1 Basics 1-2 1.1.5 Distribu
Page 21 and 22:
Chapter 2 Specifications 2-1 2.1 Sp
Page 23 and 24:
Chapter 2 Specifications 2) Operati
Page 25 and 26:
Chapter 3 Installation Note 3-2 Cau
Page 27 and 28:
Chapter 3 Installation 3) SV0110-01
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Chapter 3 Installation 3-10 2) SV00
Page 35 and 36:
Page 37 and 38:
Chapter 3 Installation 3.1.5 Dimens
Page 39 and 40:
Chapter 3 Installation 2) Mounting
Page 41 and 42:
4.1 Wiring 4.1.1 How to separate fr
Page 43 and 44:
4.1.2 How to separate front cover w
Page 45 and 46:
3) How to set EMC Filter functions
Page 47 and 48:
4.1.6 Terminal wiring diagram (POWE
Page 49 and 50:
3) 90 ~ 160 kW (400V) R(L1) S(L2) T
Page 51 and 52:
4.1.9 Control terminal line diagram
Page 53 and 54:
1) Example of Distribution Relay2 (
Page 55 and 56:
Input signal Output Signal 4.1.11 C
Page 57 and 58:
4.2 Operation Checking Chapter 4 Wi
Page 59 and 60:
5.1 Peripheral Devices Ground 5.1.1
Page 61 and 62:
2) AC Reactor Specifications INVERT
Page 63 and 64:
4) Dimensions - Group 1 - Group 2 5
Page 65 and 66:
6.1 How to Use Keypad 6.1.1 Standar
Page 67 and 68:
3) Composition of Display (1) Monit
Page 69 and 70:
No Function Display Description FWD
Page 71 and 72:
Chapter 6 How to Use Keypad 1) Para
Page 73 and 74:
2) Mode Shift with User/Macro Mode
Page 75 and 76:
PAR PRT N STP 0.00Hz 00 Jump Code 4
Page 77 and 78:
2) Code shift (function Items) in o
Page 79 and 80:
6.1.6 Parameter setting 1) Paramete
Page 81 and 82:
6.1.7 Operating status monitoring 1
Page 83 and 84:
3) How to use status display Chapte
Page 85 and 86:
3) Saving and monitoring of failure
Page 87 and 88:
7.1 Basic Functions 7.1.1 How to se
Page 89 and 90:
Chapter 7 Basic Functions IN-05 V1
Page 91 and 92:
The output frequency of bipolar vol
Page 93 and 94:
Chapter 7 Basic Functions 5) Freque
Page 95 and 96:
Chapter 7 Basic Functions If you se
Page 97 and 98:
[Example of speed-8] Chapter 7 Basi
Page 99 and 100:
Chapter 7 Basic Functions 4) Operat
Page 101 and 102:
7.1.8 Run immediately with power On
Page 103 and 104:
Caution Chapter 7 Basic Functions 9
Page 105 and 106:
Chapter 7 Basic Functions You can c
Page 107 and 108:
7.1.12 Acc/Dec Stop command Group C
Page 109 and 110:
Chapter 7 Basic Functions The user
Page 111 and 112:
Chapter 7 Basic Functions 7.1.16 Se
Page 113 and 114:
Frequency Voltage Current Operating
Page 115 and 116:
Chapter 7 Basic Functions (1) ADV-2
Page 117 and 118:
7.1.21 Multi-function input termina
Page 119 and 120:
Chapter 8 Applied Functions 8-2 Set
Page 121 and 122:
Chapter 8 Applied Functions If 10.4
Page 123 and 124:
Chapter 8 Applied Functions 8.1.3 U
Page 125 and 126:
Chapter 8 Applied Functions 8.1.5 S
Page 127 and 128:
Chapter 8 Applied Functions * Accel
Page 129 and 130:
Chapter 8 Applied Functions 8.1.8 P
Page 131 and 132:
Chapter 8 Applied Functions For exa
Page 133 and 134:
Chapter 8 Applied Functions 4) PID
Page 135 and 136:
Chapter 8 Applied Functions 8-18 In
Page 137 and 138:
Chapter 8 Applied Functions APO-05
Page 139 and 140:
Chapter 8 Applied Functions BAS-15
Page 141 and 142:
Chapter 8 Applied Functions Before
Page 143 and 144:
Chapter 8 Applied Functions lower O
Page 145 and 146:
Chapter 8 Applied Functions 1) Prep
Page 147 and 148:
Chapter 8 Applied Functions CON-48
Page 149 and 150:
Chapter 8 Applied Functions Group C
Page 151 and 152:
Chapter 8 Applied Functions If the
Page 153 and 154:
Chapter 8 Applied Functions 8.1.19
Page 155 and 156:
Chapter 8 Applied Functions ADV-61
Page 157 and 158:
Chapter 8 Applied Functions The car
Page 159 and 160:
Chapter 8 Applied Functions 8-42 Co
Page 161 and 162:
Page 163 and 164:
Chapter 8 Applied Functions 8-46 Ca
Page 165 and 166:
Chapter 8 Applied Functions 2) How
Page 167 and 168:
Chapter 8 Applied Functions CNF-42
Page 169 and 170:
Chapter 8 Applied Functions AUT-01
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Chapter 8 Applied Functions APO-41
Page 177 and 178:
Chapter 8 Applied Functions 3) Inte
Page 179 and 180:
Chapter 8 Applied Functions ADV-75
Page 181 and 182:
Chapter 9 Monitor Functions 9-2 Set
Page 183 and 184:
Chapter 9 Monitor Functions * Warni
Page 185 and 186:
Chapter 9 Monitor Functions 2) Fail
Page 187 and 188:
Chapter 9 Monitor Functions 9-8 Set
Page 189 and 190:
Chapter 9 Monitor Functions 9.1.4 S
Page 191 and 192:
Chapter 9 Monitor Functions 4 : FDT
Page 193 and 194:
Chapter 9 Monitor Functions Functio
Page 195 and 196:
Chapter 9 Monitor Functions 9.1.5 F
Page 197 and 198:
Chapter 9 Monitor Functions CNF-71
Page 199 and 200:
Chapter 10 Protective Functions PRT
Page 201 and 202:
Chapter 10 Protective Functions PRT
Page 203 and 204:
10.1.4 Motor overheat sensor input
Page 205 and 206:
Setting Items Functions bit2 bit1 O
Page 207 and 208:
1) Speed Command Loss Chapter 10 Pr
Page 209 and 210:
T _ dec Example 1) % ED = × 100[%]
Page 211 and 212:
10.1.12 Speed variation failure Thi
Page 213 and 214:
10.1.19 Detection of motor not conn
Page 215 and 216:
Category Loader Display Description
Page 217 and 218:
Chapter 11 Communication Function 1
Page 219 and 220:
Page 221 and 222:
Chapter 11 Communication Function C
Page 223 and 224:
Page 225 and 226:
Page 227 and 228:
Chapter 11 Communication Function M
Page 229 and 230: Chapter 11 Communication Function F
Page 231 and 232: Chapter 11 Communication Function 1
Page 233 and 234: Chapter 11 Communication Function A
Page 241 and 242: Chapter 11 Communication Function 2
Page 245 and 246: Chapter 12 Checking and Troubleshoo
Page 247 and 248: 12.1.3 Troubleshooting Chapter 12 C
Page 249 and 250: 12.1.4 Replacement of cooling fan C
Page 251 and 252: 12.1.5 Daily and regular checkup li
Page 253 and 254: Chapter 13 Table of Functions 13.1
Page 255 and 256: Chapter 13 Table of Functions 13.1.
Page 257 and 258: Chapter 13 Table of Functions 13-5
Page 261 and 262: Chapter 13 Table of Functions Exten
Page 265 and 266: Chapter 13 Table of Functions Contr
Page 267 and 268: Chapter 13 Table of Functions Contr
Page 269 and 270: Chapter 13 Table of Functions Input
Page 277 and 278: Chapter 13 Table of Functions Commu
Page 279: Chapter 13 Table of Functions 3.1.8
Page 283 and 284: Chapter 13 Table of Functions No. 1
Page 287 and 288: Chapter 13 Table of Functions No. C
Page 289 and 290: Chapter 13 Table of Functions No. 1
Page 291 and 292: Chapter 13 Table of Functions 3.1.1
Page 293 and 294: Chapter 13 Table of Functions 13-41
Page 295 and 296: ⅱ
Page 297 and 298: ��
Page 299: Revision History No Date Edition Ve
show all

SV-iS7 User Manual - Inverter Drive Supermarket

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?