Rexroth Tightening System 350 System Documentation - Rhino ...

More documents

Recommendations

Info

194/316 Bosch Rexroth AG | Tightening Technology 8 Basic Commissioning8.6 Operating the ErgoSpin hand-held nutrunnerTo start the tightening program to tighten the screw:1. In the program selection, select the program number, e.g. 1: Test tightening.2. Click on Start.3. Press the start button on the ErgoSpin within 15 s.To start the loosening program:⇒ Click on Loosen to start the loosening program (program 99, Ccw) independently of the programselection.Further functions– Stop stops the running program prematurely.– Reset acknowledges class 3 errors.– Standard indicates the number of times the selected tightening program can be started in a row.The system status displays are activated by selecting Start, Stop, or Loosen.The system status display to the left indicates the hardware's system status:– Green: Tightening channel is ready for operation– Red: System errorThe system status display to the right supplies information about the last tightening job:– Red: The last tightening result is NOK– Green: The last tightening result is OK– Gray: Invalid status, i.e. tightening channel is not ready for operation again or no tightening job hasbeen performed yetAfter a successful sequence test, both system status displays on the control panel and on the tighteningcontroller emit a static green light.8.5.7.2 Sequence test via the TFT display of the CS351E-GNote Follow the instructions in the “ErgoSpin” operating instructions, 3 609 929 965!The generated tightening programs can also be started via the TFT display (System test → Sequencetest). Here, the functions Loosen, Start, Stop, and Reset are identical to those in the BS350.Figure 8–19:Sequence test via the TFT display8.6 Operating the ErgoSpin hand-held nutrunnerThis section describes some of the special features for operating an ErgoSpin series hand-held nutrunner.System 350 | 3 608 878 040/05.2008
8 Basic Commissioning Tightening Technology | Bosch Rexroth AG 195/3168.6 Operating the ErgoSpin hand-held nutrunnerAll hand-held nutrunners are recognized automatically, with the exception of VarioLine. As a result, an operatingsystem is not always required to configure and program the tightening channel, depending on theCompact System used:– With the CS351E-G Compact System, you can use the TFT display instead.– With the CS351E-D Compact System, a BS350 operating system is required.8.6.1 Configuring the tightening channelThe ErgoSpin tightening channel is automatically configured during commissioning (see page 195). Noconfiguration changes are required for basic commissioning. The configuration can also be done manuallyunder System → Tightening channel configuration (see page 189) if you are using additional componentsor working in offline mode.NoteGeneral information on sending files can be found under “Sending and saving tightening programs, configurationsand PLC assignment tables” from page 177.8.6.1.1 Storing the tightening programsFive tightening programs (0 to 3, 99) are stored in the ErgoSpin hand-held nutrunner at the factory. Acopy of the programs is stored on the tightening controller when the tightening controller is switched onor reset, as well as when the hand-held nutrunner is connected.NoteIf deviating tightening programs (0 to 3, 99) are already on the tightening controller, they will be overwrittenafter acknowledgement of error message code 382 if the additional function Use tightening programsfrom hand-held nutrunner (program 99 and 0 to 3) (page 184) is activated. If this additionalfunction is inactive, a dialog field will be shown in the BS350 where you can select whether to use programsfrom the hand-held nutrunner or the tightening controller.8.6.1.2 Automatic configuration of the tightening channelAutomaticcommissioningAutomatic commissioning is active if there is no existing channel configuration. Here, the components recognizedby the tightening controller are taken over in the channel configuration without querying the userand configured with a basic setting.NoteAutomatic commissioning can be forced during later operation by simultaneously deleting the channelconfiguration and PLC assignment table. In doing so, the drive components for the ESV and ESM are automaticallydeleted.The PLC assignment table is generated automatically.To call up the configuration of the tightening channel, selectSystem → Tightening channel configuration or theicon.Automatic channelconfigurationAutomatic channel configuration is active if the Automatic radio button is selected under Channel in theglobal parameters (see page 183). Automatic channel configuration makes it possible, for example, to exchangethe ErgoSpin during operation (plug & run). The ErgoSpin data is then taken over in the channelconfiguration without querying the user. All other components must be manually configured.8.6.1.3 PLC assignment tableThe PLC assignment table defines the assignment of the control signals to the tightening controller'sphysical interfaces.This assignment is largely specified in the Compact System and does not need to be changed for basiccommissioning. You can, however, optionally specify the input signal for the tool button on the hand-heldnutrunner.To do this, proceed as follows:System 350 | 3 608 878 040/05.2008
Page 1 and 2:
Rexroth Tightening System 350System
Page 3 and 4:
ContentsSchraubtechnik | Bosch Rexr
Page 5 and 6:
ContentsSchraubtechnik | Bosch Rexr
Page 7:
1 About This DocumentThis chapter c
Page 10 and 11:
10/316 Bosch Rexroth AG | Tightenin
Page 12 and 13:
Page 14 and 15:
Page 16 and 17:
Page 18 and 19:
Page 20 and 21:
Page 22 and 23:
Page 24 and 25:
Page 26 and 27:
Page 28 and 29:
Page 30 and 31:
Page 32 and 33:
Page 34 and 35:
Page 36 and 37:
Page 38 and 39:
F PAF KRF S38/316 Bosch Rexroth AG
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
Page 46 and 47:
Page 48 and 49:
Page 50 and 51:
Page 52 and 53:
Page 54 and 55:
Page 56 and 57:
Page 58 and 59:
Page 60 and 61:
Page 62 and 63:
Page 64 and 65:
Page 66 and 67:
Page 68 and 69:
Page 70 and 71:
Page 72 and 73:
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
100/316 Bosch Rexroth AG | Tighteni
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145: 144/316 Bosch Rexroth AG | Tighteni
Page 174 and 175: OKNOK191781624FGC1C3C2CS351174/316
Page 244 and 245:
Page 246 and 247:
Page 248 and 249:
Page 250 and 251:
Page 252 and 253:
Page 254 and 255:
Page 256 and 257:
Page 258 and 259:
Page 260 and 261:
Page 262 and 263:
Page 264 and 265:
Page 266 and 267:
Page 268 and 269:
Page 270 and 271:
.270/316 Bosch Rexroth AG | Tighten
Page 272 and 273:
Page 274 and 275:
Page 276 and 277:
Page 278 and 279:
Page 280 and 281:
Page 282 and 283:
Page 284 and 285:
Page 286 and 287:
Page 288 and 289:
Page 290 and 291:
Page 292 and 293:
Page 294 and 295:
Page 296 and 297:
Page 298 and 299:
Page 300 and 301:
Page 302 and 303:
Page 304 and 305:
Page 306 and 307:
Page 308 and 309:
Page 310 and 311:
Page 312 and 313:
Page 314 and 315:
Page 316:
Bosch Rexroth AGElectric Drives and
show all

Rexroth Tightening System 350 System Documentation - Rhino ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?