Rexroth Tightening System 350 System Documentation - Rhino ...

More documents

Recommendations

Info

280/316 Bosch Rexroth AG | Tightening Technology 10 Working with the System10.2 Settings with the TFT displayThe parameterization in the OK/NOK counter menu item can also be made in the BS350 viaSystem → OK/NOK counter configuration.10.2.6.1 Power on menuThe current view can be specified as the start menu with this command. A security question will appear(Fig. 10–42).Figure 10–42: Query: Power onThe current view is saved as the start screen with OK; Cancel ends this action.Not every view can be specified as the start screen. An error message will appear if this is the case(Fig. 10–43).Figure 10–43: Message: Power onThe Power on menu can be called up from any level by touching the Power on button.If the controller has been reset, the last active menu item will be displayed.10.2.6.2 OK/NOK counterThe counter record and standard values (maximum values) for the OK/NOK counter are displayed withthis command (Fig. 10–44). A further configuration of the OK/NOK counter has to be made in the BS350under System → OK/NOK counter configuration.System 350 | 3 608 878 040/05.2008
10 Working with the System Tightening Technology | Bosch Rexroth AG 281/31610.2 Settings with the TFT displayFigure 10–44: OK/NOK counterA counter record can either be assigned to the appropriate tightening program or be selected via PLCsignals CntSel 0-5. A total of 48 counter records are available.A counter record is selected with the associated button, which opens the key pad (see page 268). If thecounter configuration is selected via the program selection (Program_1 - Program_3) (see BS350System → OK/NOK counter configuration), the program name will be displayed to the right of the button(Fig. 10–44).The standard values for the OK/NOK counter can only be changed if the user is logged on (see also “Enteringthe PIN” on page 269). The appropriate standard value can then be changed via the associatedbutton, which opens the key pad. The value range for the counter is 0 to 999.Both counter values are reset with the Reset counter button.10.2.6.3 TFT display configurationThree parameters are set here (Fig. 10–45):– Language (in accordance with the loaded language pack)– System display brightness– Shut-down time – time until screen saver mode is activated.Figure 10–45: TFT display configurationThe language is selected with the selection list. Brightness and shut-down time are set with a slider control.It can be used to set the shut-down time in 5-minute increments.To change the PIN via the BS350:Changing the PINOnly the system administrator can change the PIN in the BS350 under Administration → Password administration.Any 4 to 6-digit series of numbers can be used as the HMI PIN (Human Machine InterfacePIN).System 350 | 3 608 878 040/05.2008
Page 1 and 2:
Rexroth Tightening System 350System
Page 3 and 4:
ContentsSchraubtechnik | Bosch Rexr
Page 5 and 6:
ContentsSchraubtechnik | Bosch Rexr
Page 7:
1 About This DocumentThis chapter c
Page 10 and 11:
10/316 Bosch Rexroth AG | Tightenin
Page 12 and 13:
Page 14 and 15:
Page 16 and 17:
Page 18 and 19:
Page 20 and 21:
Page 22 and 23:
Page 24 and 25:
Page 26 and 27:
Page 28 and 29:
Page 30 and 31:
Page 32 and 33:
Page 34 and 35:
Page 36 and 37:
Page 38 and 39:
F PAF KRF S38/316 Bosch Rexroth AG
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
Page 46 and 47:
Page 48 and 49:
Page 50 and 51:
Page 52 and 53:
Page 54 and 55:
Page 56 and 57:
Page 58 and 59:
Page 60 and 61:
Page 62 and 63:
Page 64 and 65:
Page 66 and 67:
Page 68 and 69:
Page 70 and 71:
Page 72 and 73:
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
100/316 Bosch Rexroth AG | Tighteni
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
Page 160 and 161:
Page 162 and 163:
Page 164 and 165:
Page 166 and 167:
Page 168 and 169:
Page 170 and 171:
Page 172 and 173:
Page 174 and 175:
OKNOK191781624FGC1C3C2CS351174/316
Page 176 and 177:
Page 178 and 179:
Page 180 and 181:
Page 182 and 183:
Page 184 and 185:
Page 186 and 187:
Page 188 and 189:
Page 190 and 191:
Page 192 and 193:
Page 194 and 195:
Page 196 and 197:
Page 198 and 199:
Page 200 and 201:
Page 202 and 203:
Page 204 and 205:
Page 206 and 207:
Page 208 and 209:
Page 210 and 211:
Page 212 and 213:
Page 214 and 215:
Page 216 and 217:
Page 218 and 219:
Page 220 and 221:
Page 222 and 223:
Page 224 and 225:
Page 226 and 227:
Page 228 and 229:
Page 230 and 231: 230/316 Bosch Rexroth AG | Tighteni
Page 270 and 271: .270/316 Bosch Rexroth AG | Tighten
Page 316: Bosch Rexroth AGElectric Drives and
show all

Rexroth Tightening System 350 System Documentation - Rhino ...

Create successful ePaper yourself

Delete template?

Save as template?