Rexroth Tightening System 350 System Documentation - Rhino ...

More documents

Recommendations

Info

256/316 Bosch Rexroth AG | Tightening Technology 10 Working with the System10.1 Settings in the BS350To enter rework instructions:1. Select the Rework instructions index card.2. Click on Edit to put the table into edit mode.3. Enter the text that should appear on the TFT display during results output for each rework code.Figure 10–3:Entering the rework instructionsTo assign a rework code to a quality code:1. Select the Quality code index card.2. In the Quality code table, select the desired quality code in the Rework code field.3. Select the rework code valid for this quality code and the corresponding rework instructions from thelist.10.1.7.2 Outputting the rework codes/instructionsThe rework codes and instructions are output on the LCD or TFT display of the Compact System.Output via LCD displayIn Compact System model CS351E-D, the rework code (RC) is output in the 4th line, alternating withother values.Output via TFT displayIn Compact System model CS351E-G, quality codes and instructions are output in the 3rd line in thestandard display (Display → Standard) and in the actual value display 2 (Display → Actual values2):System 350 | 3 608 878 040/05.2008
10 Working with the System Tightening Technology | Bosch Rexroth AG 257/31610.1 Settings in the BS350Figure 10–4:Rework code and rework instructions output on TFT displayOutput via the BS350The rework code is also output in the BS350 operating system:– Display → Actual values in the RC column– Display → Graph under the information for the quality codeOutput via data serviceRework codes are supported in the following data services:– Results output via Ethernet (FTP)– Results output on printerAdditionally, control signals (Ch x.y RC0 to Ch x.y RC4) can be output via the control signal interfaces.10.1.8 Correcting the measurement values during signal processing in the System 350The measurement values provided by the measurement transducers are automatically processed in thecontroller’s memory before storage. The following calculations are done, if necessary:– Conversion of the measurement transducer's values on the bolt– Torque correction for torques from primary and redundancy transducers– Conversion of the torques to the set unit (e.g. Nm)The calculations mentioned above are carried out during the tightening and cannot be changed later on,i.e. measurement values that are in the controller’s results storage cannot be modified.Additionally, an angle correction for the Angle target function and monitoring function is carried out, if necessary,to evaluate the tightening sequence.10.1.8.1 Correction of the angle values with the display of the attained angleThe angle correction is used to compensate for the torsion of the output drive shaft for the angle information.To do this, the system continues to determine the measurement values after the target function hasbeen reached, until the torsion in the spindle’s output drive shaft has been reduced. The measurementvalue that was measured during the reduction of the torque until the value of the torque threshold T S(= start of angle counting) is assessed as the actual angle.NoteThe angle correction is selected in the start step of each tightening program.System 350 | 3 608 878 040/05.2008
Page 1 and 2:
Rexroth Tightening System 350System
Page 3 and 4:
ContentsSchraubtechnik | Bosch Rexr
Page 5 and 6:
ContentsSchraubtechnik | Bosch Rexr
Page 7:
1 About This DocumentThis chapter c
Page 10 and 11:
10/316 Bosch Rexroth AG | Tightenin
Page 12 and 13:
Page 14 and 15:
Page 16 and 17:
Page 18 and 19:
Page 20 and 21:
Page 22 and 23:
Page 24 and 25:
Page 26 and 27:
Page 28 and 29:
Page 30 and 31:
Page 32 and 33:
Page 34 and 35:
Page 36 and 37:
Page 38 and 39:
F PAF KRF S38/316 Bosch Rexroth AG
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
Page 46 and 47:
Page 48 and 49:
Page 50 and 51:
Page 52 and 53:
Page 54 and 55:
Page 56 and 57:
Page 58 and 59:
Page 60 and 61:
Page 62 and 63:
Page 64 and 65:
Page 66 and 67:
Page 68 and 69:
Page 70 and 71:
Page 72 and 73:
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
100/316 Bosch Rexroth AG | Tighteni
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
Page 160 and 161:
Page 162 and 163:
Page 164 and 165:
Page 166 and 167:
Page 168 and 169:
Page 170 and 171:
Page 172 and 173:
Page 174 and 175:
OKNOK191781624FGC1C3C2CS351174/316
Page 176 and 177:
Page 178 and 179:
Page 180 and 181:
Page 182 and 183:
Page 184 and 185:
Page 186 and 187:
Page 188 and 189:
Page 190 and 191:
Page 192 and 193:
Page 194 and 195:
Page 196 and 197:
Page 198 and 199:
Page 200 and 201:
Page 202 and 203:
Page 204 and 205:
Page 206 and 207: 206/316 Bosch Rexroth AG | Tighteni
Page 270 and 271: .270/316 Bosch Rexroth AG | Tighten
Page 306 and 307:
Page 308 and 309:
Page 310 and 311:
Page 312 and 313:
Page 314 and 315:
Page 316:
Bosch Rexroth AGElectric Drives and
show all

Rexroth Tightening System 350 System Documentation - Rhino ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?