Rexroth Tightening System 350 System Documentation - Rhino ...

More documents

Recommendations

Info

86/316 Bosch Rexroth AG | Tightening Technology 7 Data Services7.2 Ethernet communicationNoteIf an ID code file is transferred by FTP to the tightening system, any existing file with the same name willbe overwritten. It is not necessary to delete this file before transferring.Note The general ID code settings can be found in section “Identification codes” on page 79.The options “Delete ID code after start” and “Extend ID code with sequence number” are supported whentransferring ID codes via FTP.Table 7–3 illustrates how the ID codes are used in the results output, depending on the ID code availability.The ID code must be available before the tightening channel is started (Ch x.y Cw orCh x.y Ccw).Table 7–3: ID codes usedID code source set in BS350 ID code provision ID code used in the results outputFTP/Ethernet File available ID code from fileNo file available (ID code deleted) Cycle counterConfiguration of the tightening system as an FTP serverThe tightening system has to be configured as an FTP server in order to receive the ID code files. Thereby,the partner controller has write access to the IDCode directory.Access to the tightening systems's mass storage is protected by a user name/password. The partner controller'sFTP client must thus log in (using the commands user [user name] and pass [password]),before it can transfer a file.To configure the tightening system as an FTP server:1. In the BS350 operating system, click on System → Tightening cell data → FTP.2. Select the ID code index card.3. Enter the user name and password to access the FTP server.Only one user account can be created in the FTP server for the tightening system. However, two sessionscan be active at the same time, both of which may use this user account.NoteThe configured information on user name and password must be entered in the partner controller's FTPclient in order for the FTP client to be able to log in to the tightening system's FTP server.Authorized characters in the ID code fileIn order to be able to generate a valid file from the character sequence in the ID code file, the charactersused must correspond to the file name conventions for MS-DOS. The following characters, among others,are allowed:– a-z– A-Z– 0-9– _ (underscore)All other characters (including periods (.) and empty spaces) are accepted by the tightening system. Theywill be presented unchanged in the results output, however, an underscore (_) will be used for the filename.ExampleID code file contents (exactly the first 27 characterswere selected for masking):Resulting file name:AB 123.4_567,89.10C,ˆ% TESTCh_AB_123_4_567_89_10C____TEST.txtSystem 350 | 3 608 878 040/05.2008
7 Data Services Tightening Technology | Bosch Rexroth AG 87/3167.2 Ethernet communication7.2.2 Results output via FTP7.2.2.1 Configuration of the FTP connection for results outputTo configure the tightening system for results output via FTP:1. In the BS350 operating system, click on System → Tightening cell data.2. Click on FTP.3. Select the File system index card.Figure 7–6:Setting for results output via FTP4. In the FTP server menu, enter all of the necessary data for the FTP server where the results filesshould be stored:IP address/DNS: You can either directly enter the FTP server's IP address or its name (must alreadybe listed in the DNS server).Directory for the tightening results: Beginning with the root directory 1) of the user (with the username configured below) enter the target directory for the results files.User name: The user name has to be valid on the FTP server and have write access to the targetdirectory and authorization to create directories. If necessary, ask your system administrator if theuser has write access.Password: The password is not entered in code. The FTP convention applies here.NoteIf no directory has been entered, the root directory for the indicated user will automatically be used as thestorage location.1) This refers to the root directory for the registered user. This directory can be located several levelsbelow the actual root directory of the drive.System 350 | 3 608 878 040/05.2008
Page 1 and 2:
Rexroth Tightening System 350System
Page 3 and 4:
ContentsSchraubtechnik | Bosch Rexr
Page 5 and 6:
ContentsSchraubtechnik | Bosch Rexr
Page 7:
1 About This DocumentThis chapter c
Page 10 and 11:
10/316 Bosch Rexroth AG | Tightenin
Page 12 and 13:
Page 14 and 15:
Page 16 and 17:
Page 18 and 19:
Page 20 and 21:
Page 22 and 23:
Page 24 and 25:
Page 26 and 27:
Page 28 and 29:
Page 30 and 31:
Page 32 and 33:
Page 34 and 35:
Page 36 and 37: 36/316 Bosch Rexroth AG | Tightenin
Page 38 and 39: F PAF KRF S38/316 Bosch Rexroth AG
Page 100 and 101: 100/316 Bosch Rexroth AG | Tighteni
Page 136 and 137:
136/316 Bosch Rexroth AG | Tighteni
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
Page 160 and 161:
Page 162 and 163:
Page 164 and 165:
Page 166 and 167:
Page 168 and 169:
Page 170 and 171:
Page 172 and 173:
Page 174 and 175:
OKNOK191781624FGC1C3C2CS351174/316
Page 176 and 177:
Page 178 and 179:
Page 180 and 181:
Page 182 and 183:
Page 184 and 185:
Page 186 and 187:
Page 188 and 189:
Page 190 and 191:
Page 192 and 193:
Page 194 and 195:
Page 196 and 197:
Page 198 and 199:
Page 200 and 201:
Page 202 and 203:
Page 204 and 205:
Page 206 and 207:
Page 208 and 209:
Page 210 and 211:
Page 212 and 213:
Page 214 and 215:
Page 216 and 217:
Page 218 and 219:
Page 220 and 221:
Page 222 and 223:
Page 224 and 225:
Page 226 and 227:
Page 228 and 229:
Page 230 and 231:
Page 232 and 233:
Page 234 and 235:
Page 236 and 237:
Page 238 and 239:
Page 240 and 241:
Page 242 and 243:
Page 244 and 245:
Page 246 and 247:
Page 248 and 249:
Page 250 and 251:
Page 252 and 253:
Page 254 and 255:
Page 256 and 257:
Page 258 and 259:
Page 260 and 261:
Page 262 and 263:
Page 264 and 265:
Page 266 and 267:
Page 268 and 269:
Page 270 and 271:
.270/316 Bosch Rexroth AG | Tighten
Page 272 and 273:
Page 274 and 275:
Page 276 and 277:
Page 278 and 279:
Page 280 and 281:
Page 282 and 283:
Page 284 and 285:
Page 286 and 287:
Page 288 and 289:
Page 290 and 291:
Page 292 and 293:
Page 294 and 295:
Page 296 and 297:
Page 298 and 299:
Page 300 and 301:
Page 302 and 303:
Page 304 and 305:
Page 306 and 307:
Page 308 and 309:
Page 310 and 311:
Page 312 and 313:
Page 314 and 315:
Page 316:
Bosch Rexroth AGElectric Drives and
show all

Rexroth Tightening System 350 System Documentation - Rhino ...

Create successful ePaper yourself

Delete template?

Save as template?