Metric Tutorials - Autodesk

More documents

Recommendations

Info

10 On the Design Bar, click Modify. 11 Click File menu ➤ Save. 12 Proceed to the next exercise, Creating and Viewing a Rebar Set on page 66. Creating and Viewing a Rebar Set In this exercise, you create a rebar set within the concrete beam, and then view it in 3D. Training File Continue to use the project training file saved in the previous exercise, m_RST_EW_Detailing.rvt. Create the rebar set 1 In the Project Browser, click Sections (Building Section) ➤ Section 3. 2 Click the stirrup to select it. 66 | Chapter 2 Express Workshops 3 On the Options Bar, for Layout, select Maximum Spacing, and for Spacing, enter 150.0.
Setup views 4 In the Project Browser, click Views (all) ➤ 3D Views ➤ 3D. For the remainder of this exercise, this view is referred to as the 3D view. 5 In the Project Browser, click Sections (Building Section) ➤ Section 3. For the remainder of this exercise, this view is referred to as the section view. 6 Click Window menu ➤ Tile. The section view and the 3D views now display in separate windows in the drawing area. 7 Close any additional windows that may have been opened accidentally. View the rebar set in 3D 8 Click inside the section view and do the following: ■ On the Toolbar click . ■ Draw a zoom box around the entire section view. 9 Click inside the 3D view, and do the following: ■ On the Toolbar click . ■ Draw a zoom box around the concrete beam. Creating and Viewing a Rebar Set | 67
Page 1 and 2:
Revit Structure 2009 Metric Tutoria
Page 3:
copyright owner or contributors of
Page 6 and 7:
Modifying Snap Settings . . . . . .
Page 8 and 9:
Annotating . . . . . . . . . . . .
Page 10 and 11:
Adding Slope Arrows to a Shed Roof
Page 12 and 13:
The Contents tab of the Revit Struc
Page 14 and 15:
10 In the left pane of the Choose T
Page 16 and 17:
Understanding Autodesk Revit Struct
Page 18 and 19:
The Menu Bar The Toolbar By default
Page 20 and 21:
The Design Bar is located on the le
Page 22 and 23:
You can use the Project Browser to
Page 24 and 25:
18 On the Design Bar, click Modify.
Page 26 and 27: 5 Click Zoom Out (2x). In the drawi
Page 28 and 29: End a command 18 On the Undo menu,
Page 30 and 31: Creating a New Project In this firs
Page 32 and 33: 2 Click File menu ➤ Import/Link
Page 34 and 35: Adding Column Grids In this exercis
Page 36 and 37: 13 Select the next grid line below
Page 38 and 39: Training File Continue to use the p
Page 40 and 41: 11 Using the same method, place a c
Page 42 and 43: 7 Drag the wall towards the left ed
Page 44 and 45: 34 | Chapter 2 Express Workshops
Page 46 and 47: Notice the completed structural wal
Page 48 and 49: 9 Sketch lines along the drawing pe
Page 50 and 51: 9 On the Design Bar, click Symbolic
Page 52 and 53: 17 Click File menu ➤ Save. 18 Pro
Page 54 and 55: Adding Foundations 13 Click File me
Page 56 and 57: NOTE The individual isolated founda
Page 58 and 59: View rebar in 3D 4 Enter ZF (Zoom t
Page 60 and 61: Footing reinforcement detail Column
Page 62 and 63: Notice that the area reinforcement
Page 64 and 65: Add a break line 54 | Chapter 2 Exp
Page 66 and 67: 18 On the Design Bar, click Modify.
Page 68 and 69: 25 On the Design Bar, click Modify.
Page 70 and 71: Copy the rebar 13 On the Design Bar
Page 72 and 73: 22 Click to place the rebar. 23 Wit
Page 74 and 75: 3 On the Options Bar, click (Edit C
Page 78 and 79: ■ On the View Control Bar, for Mo
Page 80 and 81: Importing/Linking a DWG File In thi
Page 83 and 84: Modifying Project and System Settin
Page 85 and 86: 27 Click Settings menu ➤ Options.
Page 87 and 88: 13 Navigate to C:\My Documents or a
Page 89 and 90: Modifying Snap Settings 25 Proceed
Page 91 and 92: 16 Place the cursor over the horizo
Page 93 and 94: All of the exterior walls of this p
Page 95 and 96: TIP Typically, your training files
Page 97 and 98: 3 On the View Control Bar, click Mo
Page 99 and 100: 11 Click View menu ➤ Visibility/G
Page 101 and 102: 27 On the View Toolbar, click . Not
Page 103 and 104: 23 Click File menu ➤ Save. 24 Pro
Page 105 and 106: ■ Completed Structure w/ Roof&Flo
Page 107 and 108: 7 Click View menu ➤ Zoom ➤ Zoom
Page 109 and 110: The Perspective Line Weights tab co
Page 111 and 112: NOTE You cannot select specific sca
Page 113 and 114: Settings Menu Command Structural Se
Page 115 and 116: Modifying Views and View Templates
Page 117 and 118: 29 To create additional 3D views, c
Page 119 and 120: 3 Under General, enter the desired
Page 121 and 122: In this exercise, detailed instruct
Page 123 and 124: 3 Under Settings, click Setup. 4 Cl
Page 125 and 126: Starting a New Project In this tuto
Page 127 and 128:
The halftone of the imported drawin
Page 129 and 130:
The halftone of the imported drawin
Page 131 and 132:
Set options Exterior facade outline
Page 133 and 134:
Copying levels NOTE If you are prom
Page 135 and 136:
Manage links 27 In the Element Prop
Page 137 and 138:
Creating a Structural Model In this
Page 139 and 140:
As you select subsequent grid lines
Page 141 and 142:
20 Click the column to select the a
Page 143 and 144:
25 Click File menu ➤ Close. To sa
Page 145 and 146:
7 Press ESC. Notice that columns ar
Page 147 and 148:
Adding Horizontal Framing In this e
Page 149 and 150:
NOTE If necessary, you can select t
Page 151 and 152:
12 On the Design Bar, click Finish
Page 153 and 154:
Automatically create a beam system
Page 155 and 156:
Beam system displays with dashed li
Page 157 and 158:
Revit Structure provides a deck spa
Page 159 and 160:
■ Enter SM (keyboard shortcut for
Page 161 and 162:
3 On the Modelling tab of the Desig
Page 163 and 164:
5 In the Filter dialog, do the foll
Page 165 and 166:
NOTE Although you previously added
Page 167 and 168:
Specify the top of steel 11 On the
Page 169 and 170:
27 Select the beam that spans the m
Page 171 and 172:
3 On the Modelling tab of the Desig
Page 173 and 174:
■ In the left pane of the Open di
Page 175 and 176:
Adding Shafts 11 Proceed to the nex
Page 177 and 178:
Duplicating Framing 18 Click File m
Page 179 and 180:
Page 181 and 182:
33 In the Filter dialog, click Chec
Page 183 and 184:
5 On the Basics tab of the Design B
Page 185 and 186:
Edit the slab 22 In the Project Bro
Page 187 and 188:
The corner points of the slab are h
Page 189 and 190:
Each line will be extended and trim
Page 191 and 192:
Page 193 and 194:
Sketch split lines 3 Select the atr
Page 195 and 196:
Place additional points Delete spli
Page 197 and 198:
View section view of slab 18 In the
Page 199 and 200:
Page 201 and 202:
Add the miter join 3 On the View Co
Page 203 and 204:
The miter join is complete. 9 Click
Page 205 and 206:
Notice the miter lock remains locke
Page 207 and 208:
8 Click the grid line so the beam s
Page 209 and 210:
14 In the Element Properties dialog
Page 211 and 212:
Approximate the curve of the analyt
Page 213 and 214:
3 On the Architectural tab of the D
Page 215 and 216:
Page 217 and 218:
Change the stiffener plate properti
Page 219 and 220:
14 On the Family Design Bar, click
Page 221 and 222:
30 Navigate to a folder of your pre
Page 223 and 224:
Sketch the atrium walls 1 In the Pr
Page 225 and 226:
Adding Piers or Pilasters To save c
Page 227 and 228:
6 Select the exterior face of the f
Page 229 and 230:
Copy the framing and slab to Garage
Page 231 and 232:
Completed ramp Add a sloped beam sy
Page 233 and 234:
NOTE Depending on where you draw th
Page 235 and 236:
Page 237 and 238:
Precast Concrete In this tutorial,
Page 239 and 240:
9 Proceed to the next exercise, Cha
Page 241 and 242:
4 On the Options Bar, click . 5 In
Page 243 and 244:
Open the beam profile 6 In the Fami
Page 245 and 246:
22 Press ESC. 23 Click the referenc
Page 247 and 248:
37 Enter AL (this is the keyboard s
Page 249 and 250:
Modify the right tee of the beam 49
Page 251 and 252:
Creating Drawings In this tutorial,
Page 253 and 254:
NOTE The Project Path parameter in
Page 255 and 256:
NOTE If necessary, you can select t
Page 257 and 258:
NOTE This exercise requires the com
Page 259 and 260:
15 On the View Toolbar, click , and
Page 261 and 262:
Notice there are 3 typical detail v
Page 263 and 264:
Importing Details from the Library
Page 265 and 266:
■ Click OK. Because you are impor
Page 267 and 268:
■ Click Open. 11 In the Insert Vi
Page 269 and 270:
Page 271 and 272:
15 Working from the top down, enter
Page 273 and 274:
Scheduling In this tutorial, you le
Page 275 and 276:
Page 277 and 278:
■ Under Type of Parameter, select
Page 279 and 280:
Select a filter Format units A new
Page 281 and 282:
23 In the Schedule Properties dialo
Page 283 and 284:
Customizing the Type Schedule In th
Page 285 and 286:
9 While pressing CTRL, select multi
Page 287 and 288:
■ Click OK. 17 In the Element Pro
Page 289 and 290:
Group rebar columns Enter rebar dat
Page 291 and 292:
NOTE The cost value represents a ra
Page 293 and 294:
2 Right-click the column schedule,
Page 295 and 296:
■ In the Element Properties dialo
Page 297 and 298:
7 Click OK. 8 In the Element Proper
Page 299 and 300:
Split the column schedule 21 Right-
Page 301 and 302:
Add additional sheets The first seg
Page 303 and 304:
tables. For example, instance table
Page 305 and 306:
Steel Details In this tutorial, you
Page 307 and 308:
9 Draw a section as shown. 10 On th
Page 309 and 310:
Detailing Steel 32 Click File menu
Page 311 and 312:
Next, you create 2 detail lines tha
Page 313 and 314:
18 Select the middle vertical line
Page 315 and 316:
Label the angles and the plate 29 O
Page 317 and 318:
7 On the Options Bar, click . 8 Ent
Page 319 and 320:
9 Next, select the back of the chan
Page 321 and 322:
Creating a Deck Span Transition Det
Page 323 and 324:
25 On the Design bar, click Modify.
Page 325 and 326:
Concrete Reinforcement Modelling In
Page 327 and 328:
NOTE You can open or close the Reba
Page 329 and 330:
18 Pace a single rebar at the botto
Page 331 and 332:
Notice that the rebar sets are visi
Page 333 and 334:
Reinforcement in a Column In this e
Page 335 and 336:
Page 337 and 338:
View rebar in 3D 22 On the Options
Page 339 and 340:
■ In the left pane of the Open di
Page 341 and 342:
10 Use the ViewCube to rotate the m
Page 343 and 344:
Remove the major bars The area rein
Page 345 and 346:
Notice the rebar for the major span
Page 347 and 348:
Page 349 and 350:
Sketch the area reinforcement 8 In
Page 351 and 352:
The area reinforcement for the slab
Page 353 and 354:
Change bar type 5 On the Options Ba
Page 355 and 356:
NOTE The line weights in your file
Page 357 and 358:
4 Press ESC. 5 Double-click the sec
Page 359 and 360:
Sketch rebar parallel to the footin
Page 361 and 362:
Mirror the rebar 27 On the Options
Page 363 and 364:
Page 365 and 366:
48 On the Options Bar, click . 49 O
Page 367 and 368:
To save changes, click File menu
Page 369 and 370:
Place horizontal rebar ■ Click Mo
Page 371 and 372:
Page 373 and 374:
31 Drag the sketch line up towards
Page 375 and 376:
40 Press CTRL, and select the outsi
Page 377 and 378:
47 On the Toolbar, click , and draw
Page 379 and 380:
Annotating and Dimensioning In this
Page 381 and 382:
Page 383 and 384:
Create a linear dimension 29 On the
Page 385 and 386:
Page 387 and 388:
Edit dimension witness lines 12 On
Page 389 and 390:
20 To end the editing command, clic
Page 391 and 392:
position, while the second componen
Page 393 and 394:
Align the windows on the floor plan
Page 395 and 396:
2 On the Design Bar, click Dimensio
Page 397 and 398:
■ Move the cursor up and to the l
Page 399 and 400:
16 On the Options Bar, select Leade
Page 401 and 402:
Add spot coordinates to a sloped be
Page 403 and 404:
Tag all beams in plan view 1 In the
Page 405 and 406:
■ In the Beam Annotations dialog,
Page 407 and 408:
24 In the Edit Label dialog, under
Page 409 and 410:
■ Click OK. 35 In the Type Select
Page 411 and 412:
Align the beam tag ■ Under Catego
Page 413 and 414:
■ Click OK. 21 Click File ➤ Sav
Page 415 and 416:
Worksets On many building projects,
Page 417 and 418:
8 In the Worksets dialog, click New
Page 419 and 420:
You have created the required works
Page 421 and 422:
In this exercise, you enabled Works
Page 423 and 424:
All structural columns in the model
Page 425 and 426:
In the Worksets dialog, notice User
Page 427 and 428:
Assign the roof workset 13 Select t
Page 429 and 430:
25 In the Save to Central dialog, s
Page 431 and 432:
A warning is displayed informing yo
Page 433 and 434:
42 Click File menu ➤ Save to Cent
Page 435 and 436:
14 In the Editing Requests dialog,
Page 437 and 438:
Project Coordination You have recei
Page 439 and 440:
10 On the Toolbar, click , and draw
Page 441 and 442:
Review location of grid B The concr
Page 443 and 444:
Review wall modifications The eleva
Page 445 and 446:
Notice the categories for the archi
Page 447 and 448:
There are 7 instances of interferen
Page 449 and 450:
12 In the Interference Report dialo
Page 451 and 452:
If Visible is not selected, any rev
Page 453 and 454:
If Visible is not selected, any rev
Page 455 and 456:
Page 457 and 458:
The Activate View command activates
Page 459 and 460:
8 Proceed to the next tutorial, Str
Page 461 and 462:
Structural Analytical Modelling 14
Page 463 and 464:
NOTE If the visibility of loads is
Page 465 and 466:
The unsupported element is highligh
Page 467 and 468:
Run a consistency check Review warn
Page 469 and 470:
9 In the Element Properties dialog,
Page 471 and 472:
The first table is the Load Cases t
Page 473 and 474:
2 On the View Control Bar, click th
Page 475 and 476:
TIP Be sure to click the Area Load
Page 477 and 478:
■ Select WIND1(3) for Load Case,
Page 479 and 480:
This grid is drawn for reference on
Page 481 and 482:
Load Combination 36 Click File menu
Page 483 and 484:
26 In the Structural Settings dialo
Page 485 and 486:
The load combinations are displayed
Page 487 and 488:
Create a load schedule Define the f
Page 489 and 490:
3 Click Tools menu ➤ Analytical M
Page 491 and 492:
Aligns the vertical and horizontal
Page 493 and 494:
Adjust the beam to slab vertical of
Page 495 and 496:
The vertical projection plane of th
Page 497 and 498:
19 Double-click the section bubble
Page 499 and 500:
The vertical projection plane for t
Page 501 and 502:
The brown line represents the analy
Page 503 and 504:
The horizontal projection plane of
Page 505 and 506:
53 Click the beam, and on the Optio
Page 507 and 508:
Boundary Conditions In this exercis
Page 509 and 510:
Notice the boundary condition now d
Page 511 and 512:
Exporting Revit Structure Files You
Page 513 and 514:
■ Under Prefer, select AutoCAD Ar
Page 515 and 516:
Exporting a 2D view to AutoCAD Trai
Page 517 and 518:
Export sheets 1 Click File menu ➤
Page 519 and 520:
When the sheets are opened in AutoC
Page 521 and 522:
About Families and the Family Edito
Page 523 and 524:
The following illustration shows ho
Page 525 and 526:
General procedure for creating a st
Page 527 and 528:
Creating Components in the Family E
Page 529 and 530:
Modify the angular reference plane
Page 531 and 532:
18 Select the dimension that refers
Page 533 and 534:
The dimensions displayed in the fol
Page 535 and 536:
43 Select the upper dovetail dimens
Page 537 and 538:
Create a new project 59 Click File
Page 539 and 540:
83 Proceed to the next exercise, Cu
Page 541 and 542:
Notice the opening in the beam chan
Page 543 and 544:
Place dimensions 6 On the Design Ba
Page 545 and 546:
15 On the Options Bar, for Label, s
Page 547 and 548:
Launch the rebar shape browser 36 O
Page 549 and 550:
Page 551 and 552:
Sketch the extrusion Make sure the
Page 553 and 554:
27 Click to place a third copy of t
Page 555 and 556:
Join extrusion elements to each oth
Page 557 and 558:
The titleblock has linework, text,
Page 559 and 560:
18 On the Options Bar, click , and
Page 561 and 562:
Create a new 10mm text style 5 On t
Page 563 and 564:
26 Move the cursor down 120mm, and
Page 565 and 566:
Add drawing data labels 40 On the D
Page 567 and 568:
55 Click OK twice. Add sheet number
Page 569 and 570:
Adding the Titleblock to a New Proj
Page 571 and 572:
Truss Building In this tutorial, yo
Page 573 and 574:
The truss is placed between the col
Page 575 and 576:
21 Enter ZF (keyboard shortcut for
Page 577 and 578:
35 Click the top endpoint of the co
Page 579 and 580:
Modify each truss 40 On the View to
Page 581 and 582:
8 In the Element Properties dialog,
Page 583 and 584:
NOTE Check the Status Bar to make s
Page 585 and 586:
Attach the roof 3 Click Edit menu
Page 587 and 588:
Creating a Custom Truss Family In t
Page 589 and 590:
14 Click the intersection of the bo
Page 591 and 592:
27 In the Project Browser, under 3D
Page 593 and 594:
Add framing elevations 8 On the Bas
Page 595 and 596:
24 On the Tools toolbar, click . 25
Page 597 and 598:
36 On the Design Bar, click Ref Pla
Page 599 and 600:
The completed truss is displayed. 4
Page 601 and 602:
Creating Multiple Design Options Wh
Page 603 and 604:
4 In the Project Browser, expand Vi
Page 605 and 606:
Notice the 12 columns that you adde
Page 607 and 608:
Notice that the beams complete the
Page 609 and 610:
55 On the Basics tab of the Design
Page 611 and 612:
Three more roof beams are placed at
Page 613 and 614:
11 On the Basics tab of the Design
Page 615 and 616:
Add the louvers to the design optio
Page 617 and 618:
The louver roof system is complete.
Page 619 and 620:
The louver roof system is complete.
Page 621 and 622:
14 In the Project Browser, under Vi
Page 623 and 624:
Linking Building Models and Sharing
Page 625 and 626:
■ Auto - Origin to Origin: The or
Page 627 and 628:
The condo complex building model is
Page 629 and 630:
Rotate the townhouse The townhouse
Page 631 and 632:
Copy the townhouse The townhouse is
Page 633 and 634:
38 On the File menu, click Save. NO
Page 635 and 636:
Notice that the townhouse is now at
Page 637 and 638:
Apply halftone 12 Using the same te
Page 639 and 640:
Page 641 and 642:
10 In the Save As dialog, navigate
Page 643 and 644:
4 In the Manage Place and Locations
Page 645 and 646:
Save locations Notice the OK button
Page 647 and 648:
Working with a Linked Building Mode
Page 649 and 650:
7 Click View menu ➤ Zoom ➤ Zoom
Page 651 and 652:
8 Click OK. Sort schedule data In o
Page 653 and 654:
Project Phasing In any project, you
Page 655 and 656:
Phase 2 (north) After you add phase
Page 657 and 658:
In the Element Properties dialog, n
Page 659 and 660:
23 Use a crossing window to select
Page 661 and 662:
to determine which phase is shown a
Page 663 and 664:
Apply the Demo Red graphic override
Page 665 and 666:
Dataset ■ Click File menu ➤ Ope
Page 667 and 668:
20 In the Project Browser, expand F
Page 669 and 670:
Rendering Views and Creating Walkth
Page 671 and 672:
Training File ■ Click File menu
Page 673 and 674:
11 In the Render Appearance Library
Page 675 and 676:
32 Click Settings menu ➤ Object S
Page 677 and 678:
42 Specify options in the Rendering
Page 679 and 680:
3 On the Site tab of the Design Bar
Page 681 and 682:
Page 683 and 684:
3 Zoom out, and select the crop bou
Page 685 and 686:
Creating the Exterior Rendering In
Page 687 and 688:
9 In the Rendering dialog, click Sh
Page 689 and 690:
Adjust the exposure 28 In the Rende
Page 691 and 692:
Add an RPC figure to the view 1 In
Page 693 and 694:
15 Proceed to the next exercise, Cr
Page 695 and 696:
7 Click Window menu ➤ Close Hidde
Page 697 and 698:
15 Maximize the 3D view, and adjust
Page 699 and 700:
9 Close the Rendering dialog. Creat
Page 701 and 702:
Page 703 and 704:
■ Shading with Edges ■ Renderin
Page 705 and 706:
8 Verify that the crop boundary of
Page 707 and 708:
5 Select the target point of the ca
Page 709 and 710:
Roofs In this tutorial, you learn h
Page 711 and 712:
9 Sketch a similar reference plane
Page 713 and 714:
Notice that the breezeway roof pene
Page 715 and 716:
You begin by sketching the perimete
Page 717 and 718:
Creating a Roof with a Vertical Pen
Page 719 and 720:
18 On the View toolbar, click (Defa
Page 721 and 722:
12 Repeat the trim procedure on the
Page 723 and 724:
Creating a Shed Roof from a Footpri
Page 725 and 726:
2 Select the shed roof over the ent
Page 727 and 728:
4 Select the two gable end lines (t
Page 729 and 730:
6 On the View toolbar, click (Defau
Page 731 and 732:
Create a flat roof by footprint 1 I
Page 733 and 734:
Open a section view 12 In the drawi
Page 735 and 736:
Add elevation points The roof is no
Page 737 and 738:
27 Press and hold CTRL, and select
Page 739 and 740:
Creating Roof Fascia In this exerci
Page 741 and 742:
3 In the Properties dialog, click E
Page 743 and 744:
4 Select the roof. 5 On the Design
Page 745 and 746:
Grouping Using the grouping functio
Page 747 and 748:
3 Draw a selection box (lower-right
Page 749 and 750:
Place instances of the group 9 In t
Page 751 and 752:
17 Select the kitchen in the stairw
Page 753 and 754:
Save the training file Modifying a
Page 755 and 756:
Add elements for a unique condition
Page 757 and 758:
Nesting Groups 25 On the Design Bar
Page 759 and 760:
6 Press TAB, select the wall betwee
Page 761 and 762:
3 On the Drafting tab of the Design
Page 763 and 764:
Page 765 and 766:
7 On the Options Bar, click (Filter
Page 767 and 768:
Continue using the training file sa
show all

Metric Tutorials - Autodesk

Create successful ePaper yourself

Delete template?

Save as template?