SIREC D Display Recorder 7ND4000
SIREC D Display Recorder 7ND4000
SIREC D Display Recorder 7ND4000
Erfolgreiche ePaper selbst erstellen
Machen Sie aus Ihren PDF Publikationen ein blätterbares Flipbook mit unserer einzigartigen Google optimierten e-Paper Software.
3. Trigger - Selecting Trigger will arm the unit to<br />
record when an external or internal event takes<br />
place. Internal Record-On-Alarm Triggers are set<br />
in the Record Setup menu while External Event<br />
Triggers are set in the Digital Input/Output Setup<br />
menu under the PROGram Button. If the <strong>Recorder</strong><br />
is set in the record TRIGGER mode, either<br />
of these event triggers will control the Record<br />
ON or Record OFF function depending on<br />
whether the events are active or inactive. To set<br />
the Record Mode to Trigger, perform the following<br />
steps and refer to Figure 3-32:<br />
1 0 3 7 2 2 M A<br />
a. Use the UP (↑) or DOWN (↓) Arrow Keys to<br />
highlight “Record On/Off” and press ENTER.<br />
b. Use the UP (↑) or DOWN (↓) Arrow Keys to<br />
highlight “Trigger” and then press ENTER.<br />
c. A pop up window will ask to confirm the selection<br />
“trigger on?”. Press “YES” to accept the<br />
Trigger ON state or “No” to exit without turning<br />
the trigger mode ON.<br />
VIEW BR OW S 04/16/97 4:59:29 JOG MENU<br />
ENTER<br />
ENTER<br />
ENTER<br />
ENTER<br />
trigger on?<br />
DISP 04/16/97 PROG 4:59:29 FUNC EXIT<br />
04/16/97 4:59:29 EXIT<br />
04/16/97 4:59:29 EXIT<br />
YES NO EXIT<br />
04/16/97 4:59:29 EXIT<br />
Figure 3-32 Turn Trigger Mode to ON Flow<br />
Chart<br />
NOTE<br />
Triggered recordings can only be made if<br />
the disk record mode is set to Fill-To-End.<br />
See Chapter 4. Cyclic files cannot be triggered.<br />
Siemens AG C79000-G7374-C211-01<br />
<strong>SIREC</strong> D Manual<br />
NOTE<br />
Operation<br />
Trigger Mode can be invoked with the <strong>Recorder</strong><br />
in the Record ON or OFF Mode.<br />
With the Trigger Mode turned ON, the current<br />
record status is shown in the Disk Info<br />
Window in the top right corner of the<br />
screen. If the unit is not recording, this window<br />
will show REC TRIG. To start recording,<br />
without waiting for a trigger, turn Record<br />
ON as detailed in paragraph 3.4.4.A.2.<br />
B. Activate Point - This menu item returns a<br />
temporarily bypassed point or points to the<br />
measurement cycle for measuring inputs and<br />
displaying information. To activate a point perform<br />
the following steps and use the flow chart shown in<br />
Figure 3-33:<br />
1. Press the FUNC Key on the Main Menu Bar.<br />
2. Use the UP (↑) or DOWN (↓) Arrow Keys to<br />
highlight “Activate pt” and press ENTER.<br />
3. Use the pup-up numeric keypad to enter the<br />
point number to activate and press ENTER on<br />
the Menu Bar.<br />
4. The display then scrolls to the next point.<br />
When point activation is finished, press EXIT in<br />
the pop-up keypad and the display will return to<br />
the “Activate pt” display.<br />
103723MA<br />
VIEW BROW S 04/16/97 4:59:29 JOG MENU<br />
ENTER<br />
ENTER<br />
DISP 04/16/97 PR4:59:29 OG FUNC EXIT<br />
04/16/97 4:59:29 EXIT<br />
A<br />
B<br />
C<br />
P oint? 1<br />
7 8 9<br />
4 5 6<br />
3 2 1<br />
04/16/97 4:59:29 EXIT EXIT<br />
Figure 3-33 Activate Point Flow Chart<br />
3-17