substitution request - Alliance Construction Solutions

Recommendations

Info

c. National Gypsum Company; Gold Bond Brand Fire-Shield Shaftliner. d. USG Corporation; Sheetrock Brand Gypsum Liner Panel. C. Gypsum Board: As specified in Division 09 Section "Gypsum Board." 2.4 NON-LOAD-BEARING STEEL FRAMING A. Steel Framing Members: Comply with ASTM C 645 requirements for metal. PART 3 - EXECUTION 3.1 INSTALLATION A. General: Comply with requirements of fire-resistance-rated assemblies indicated, manufacturer's written installation instructions, and ASTM C 754 other than studspacing requirements. B. Isolate perimeter of gypsum panels from building structure, while maintaining continuity of fire-rated construction. C. Installation Tolerance: Install each framing member so fastening surfaces vary not more than 1/8 inch from the plane formed by faces of adjacent framing. D. Remove and replace panels that are wet, moisture damaged, or mold damaged. END OF SECTION 09 2116 Project No.: 10145 GYPSUM BOARD SHAFT WALL ASSEMBLIES 550 15th Street Dual Brand Hotel 09211623 - 2 19 March 2012
PART 1 - GENERAL 1.1 SUMMARY SECTION 09 2216 NON-STRUCTURAL METAL FRAMING A. This Section includes non-load-bearing steel framing members for the following applications: 1. Interior framing systems (e.g., supports for partition walls, framed soffits, furring, etc.). 2. Interior suspension systems (e.g., supports for ceilings, suspended soffits, etc.). 1.2 SUBMITTALS A. Product Data: For each type of product indicated. 1.3 QUALITY ASSURANCE A. Fire-Test-Response Characteristics: For fire-resistance-rated assemblies that incorporate non-load-bearing steel framing, provide materials and construction identical to those tested in assembly indicated according to ASTM E 119 by an independent testing agency. PART 2 - PRODUCTS 2.1 NON-LOAD-BEARING STEEL FRAMING, GENERAL A. Recycled Content of Steel Products: Provide products with average recycled content of steel products such that postconsumer recycled content plus one-half of preconsumer recycled content is not less than 25 percent. B. Framing Members, General: Comply with ASTM C 754 for conditions indicated. 1. Acceptable Manufacturers: Steel Stud Manufacturer’s Association members. 2. Steel Sheet Components: Comply with ASTM C 645 requirements for metal, unless otherwise indicated. 3. Protective Coating: G40 or equivalent per ASTM A 1003, unless otherwise indicated 2.2 SUSPENSION SYSTEM COMPONENTS A. Tie Wire: ASTM A 641/A 641M, Class 1 zinc coating, soft temper, 0.0625-inch- diameter wire, or double strand of 0.0475-inch- diameter wire. Project No.: 10145 NON-STRUCTURAL METAL FRAMING 550 15th Street Dual Brand Hotel 092216 - 1 19 March 2012
Page 1 and 2:
TECHNICAL SPECIFICATIONS FOR HOMEWO
Page 3 and 4:
DIVISION 06 - WOOD AND PLASTICS Sec
Page 5 and 6:
Division Section Title Pages DIVISI
Page 7 and 8:
Division Section Title Pages DIVISI
Page 9 and 10:
B. Type of Contract: 1. Project wil
Page 11 and 12:
PART 1 - GENERAL 1.1 SUMMARY SECTIO
Page 13 and 14:
c. Requested substitution has recei
Page 15 and 16:
SUBSTITUTION REQUEST (Continued) Th
Page 17 and 18:
2. Include a list of quantities of
Page 19 and 20:
a. Include separate line items unde
Page 21 and 22:
8. Final meter readings for utiliti
Page 23 and 24:
1.4 COORDINATION DRAWINGS A. Coordi
Page 25 and 26:
1. Project name. 2. Name and addres
Page 27 and 28:
9) Progress cleaning. 10) Quality a
Page 29 and 30:
PART 2 - PRODUCTS 2.1 CONTRACTOR'S
Page 31 and 32:
Page 33 and 34:
2. Intermediate Review: If intermed
Page 35 and 36:
1. If information must be specially
Page 37 and 38:
PART 3 - EXECUTION 3.1 CONTRACTOR'S
Page 39 and 40:
jurisdiction, to establish product
Page 41 and 42:
1.7 QUALITY ASSURANCE A. General: Q
Page 43 and 44:
1.9 SPECIAL TESTS AND INSPECTIONS A
Page 45 and 46:
1.5 PROJECT CONDITIONS A. Temporary
Page 47 and 48:
J. Electronic Communication Service
Page 49 and 50:
procedures to be followed. Instruct
Page 51 and 52:
proposed comparable product request
Page 53 and 54:
with requirements. Comparable produ
Page 55 and 56:
PART 2 - PRODUCTS 2.1 MATERIALS A.
Page 57 and 58:
F. Tools and Equipment: Do not use
Page 59 and 60:
1. Remove liquid spills promptly. 2
Page 61 and 62:
4. Submit maintenance material subm
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
paper; with clear plastic sleeve on
Page 69 and 70:
Page 71 and 72:
2.4 MISCELLANEOUS RECORD SUBMITTALS
Page 73 and 74:
E. Utility Service: Maintain existi
Page 75 and 76:
D. Existing Items to Remain: Protec
Page 77 and 78:
C. Verification Samples: For each p
Page 79 and 80:
B. Geo-Synthetic Fill fill shall be
Page 81 and 82:
F. Preinstallation Conference: Cond
Page 83 and 84:
F. Clear, Solvent-Borne, Membrane-F
Page 85 and 86:
2. Sawed Joints: Form contraction j
Page 87 and 88:
3.09 CONCRETE PROTECTING AND CURING
Page 89 and 90:
3.12 FIELD QUALITY CONTROL A. Testi
Page 91 and 92:
PART 1 - GENERAL 1.01 SUMMARY A. Se
Page 93 and 94:
2.03 MASONRY LINTELS A. Masonry Lin
Page 95 and 96:
2.07 MISCELLANEOUS MASONRY ACCESSOR
Page 97 and 98:
C. Joints: 1. For bed joints, do no
Page 99 and 100:
3.08 FIELD QUALITY CONTROL A. Testi
Page 101 and 102:
PART 1 - GENERAL 1.01 SUMMARY SECTI
Page 103 and 104:
1. Finish: Plain or Hot-dip zinc co
Page 105 and 106:
3.02 ERECTION A. Set structural ste
Page 107 and 108:
PART 1 - GENERAL 1.01 SUMMARY A. Th
Page 109 and 110:
2.03 NONCOMPOSITE FORM DECK A. Nonc
Page 111 and 112:
D. Remove and replace work that doe
Page 113 and 114:
Page 115 and 116:
D. Sealer Gaskets: Closed-cell neop
Page 117 and 118:
J. Install miscellaneous framing an
Page 119 and 120:
PART 1- GENERAL 1.1 SUMMARY SECTION
Page 121 and 122:
paint systems indicated, and for ca
Page 123 and 124:
2.12 PIPE BOLLARDS mitered joints f
Page 125 and 126:
Page 127 and 128:
B. Apply bituminous paint to concea
Page 129 and 130:
B. Welded Connections: Fabricate ra
Page 131 and 132:
PART 1 - GENERAL 1.1 SUMMARY A. Thi
Page 133 and 134:
Page 135 and 136:
F. Granite Countertops: With bull n
Page 137 and 138:
G. Solid Lumber: Dry, sound, select
Page 139 and 140:
E. Anchor woodwork to anchors or bl
Page 141 and 142:
PART 2 - PRODUCTS A. Tub / Shower S
Page 143 and 144:
2.2 ACCESSORIES A. Trim Accessories
Page 145 and 146:
D. Protection Course: ASTM D 6506,
Page 147 and 148:
1.5 DELIVERY, STORAGE, AND HANDLING
Page 149 and 150:
etarder to cover miscellaneous void
Page 151 and 152:
1. Basis-of-Design Product: Subject
Page 153 and 154:
C. Accessory Installation: Install
Page 155 and 156:
PART 2 - PRODUCTS 2.01 EPDM ROOFING
Page 157 and 158:
B. Install tapered insulation under
Page 159 and 160:
B. Sheet Metal Standard for Flashin
Page 161 and 162:
2.05 ROOF-DRAINAGE SHEET METAL FABR
Page 163 and 164:
D. Pipe or Post Counterflashing: In
Page 165 and 166:
PART 3 - EXECUTION 3.01 PREPARATION
Page 167 and 168:
2.02 PENETRATION FIRESTOPPING A. Pr
Page 169 and 170:
Page 171 and 172:
2. Characteristics: Single-componen
Page 173 and 174:
PART 3 - EXECUTION 3.1 PREPARATION
Page 175 and 176:
Page 177 and 178:
E. Inserts, Bolts, and Fasteners: H
Page 179 and 180:
2.5 FABRICATION A. Fabricate hollow
Page 181 and 182:
3.2 PREPARATION A. Remove welded-in
Page 183 and 184:
Page 185 and 186:
1. Install fire-rated doors accordi
Page 187 and 188:
C. Steel Finishes: Comply with NAAM
Page 189 and 190:
Page 191 and 192:
C. Glass: Provide manufacturer’s
Page 193 and 194: PART 1 - GENERAL 1.1 SUMMARY A. Sec
Page 195 and 196: 1.6 PROJECT CONDITIONS A. Field Mea
Page 197 and 198: a. Accessible Doors: Smooth surface
Page 199 and 200: G. After fabrication, clearly mark
Page 203 and 204: E. Emergency-Exit Door Requirements
Page 205 and 206: . Adjustable opening and closing sp
Page 207 and 208: . Reinforce members as required to
Page 209 and 210: G. Wiring within Automatic Entrance
Page 211 and 212: 1.3 QUALITY ASSURANCE A. Source Lim
Page 213 and 214: 2. Interior Hinges: Steel, with ste
Page 215 and 216: D. Panic Exit Devices: Listed and l
Page 217 and 218: B. Combination Overhead Stops and H
Page 219 and 220: C. Door Viewer: 200 degree door vie
Page 221 and 222: Door Hardware Set No. 6 Exterior St
Page 223 and 224: 1 Protective Trim Units Kick Plate
Page 225 and 226: Door Hardware Set No. 25 Pool Publi
Page 227 and 228: 10. Latch bolt operated by inside l
Page 229 and 230: surface temperatures of materials d
Page 231 and 232: 3. Spacer Specifications: Manufactu
Page 233 and 234: 3.2 PREPARATION A. Clean glazing ch
Page 235 and 236: PART 1 - GENERAL 1.1 SUMMARY SECTIO
Page 237 and 238: 2.2 MISCELLANEOUS MATERIALS A. Sett
Page 241 and 242: C. Fabricate frames, including inte
Page 243: PART 1 - GENERAL 1.1 SUMMARY SECTIO
Page 247 and 248: 2. Foam Gasket: Adhesive-backed, cl
Page 249 and 250: PART 1 - GENERAL 1.01 SUMMARY SECTI
Page 251 and 252: 3.03 INSTALLING ACCESSORIES A. Inst
Page 253 and 254: C. Flexible Gypsum Board: ASTM C 13
Page 255 and 256: F. Install trim with back flanges i
Page 257 and 258: 1.5 QUALITY ASSURANCE A. Source Lim
Page 259 and 260: B. Standard Cement Grout: ANSI A118
Page 261 and 262: 3.3 TILE INSTALLATION A. Comply wit
Page 265 and 266: mold, mildew, or bacterial growth w
Page 267 and 268: 3.3 INSTALLATION A. General: Instal
Page 269 and 270: 1.6 WARRANTY A. Special Warranty: M
Page 275 and 276: PART 1 - GENERAL 1.1 SUMMARY A. Thi
Page 277 and 278: F. Subfloor Alkalinity Conditions:
Page 279 and 280: I. The final carpet pattern, layout
Page 281 and 282: PART 1 - GENERAL 1.1 SUMMARY A. Thi
Page 283 and 284: 3.4 CLEANING A. Remove excess adhes
Page 285 and 286: 1.5 PROJECT CONDITIONS A. Apply pai
Page 287 and 288: E. Galvanized-Metal Substrates: Rem
Page 291 and 292: C. Quick-Drying Primer for Aluminum
Page 293 and 294: B. If undercoats or other condition
Page 295 and 296:
Page 297 and 298:
PART 3 - EXECUTION 3.01 EXAMINATION
Page 299 and 300:
Page 301 and 302:
PART 3 - EXECUTION 3.1 INSTALLATION
Page 303 and 304:
1.5 EXTRA MATERIALS A. Furnish extr
Page 305 and 306:
3.4 CLEANING A. Immediately after c
Page 307 and 308:
PART 2 - PRODUCTS 2.1 ACCESSORY SCH
Page 309 and 310:
3.2 ADJUSTING AND CLEANING A. Adjus
Page 311 and 312:
PART 1 - GENERAL 1.1 SUMMARY A. Sec
Page 313 and 314:
2.3 FABRICATION A. Fire Protection
Page 315 and 316:
Page 317 and 318:
Page 319 and 320:
B. Locker Arrangement: Double tier.
Page 321 and 322:
C. Surface Preparation: Clean surfa
Page 323 and 324:
Page 325 and 326:
PART 1 - GENERAL 1.1 SUBMITTALS SEC
Page 327 and 328:
B. Microwave Oven: 1. HWS Basis-of-
Page 329 and 330:
Page 331 and 332:
Page 333 and 334:
1.1 SUMMARY SECTION 13 1500 SWIMMIN
Page 335 and 336:
2.02 CHUTES A. Chute Metal: Aluminu
Page 337 and 338:
PART 1 - GENERAL 1.1 RELATED DOCUME
Page 339 and 340:
2.5 SINGLE-PHASE MOTORS A. Motors l
Page 341 and 342:
B. Product Certificates: For each t
Page 343 and 344:
C. Rubber Packless Expansion Joints
Page 345 and 346:
B. Install metal-bellows expansion
Page 347 and 348:
Page 349 and 350:
D. Install sleeves for pipes passin
Page 351 and 352:
Page 353 and 354:
Page 355 and 356:
d. Tel-Tru Manufacturing Company. e
Page 357 and 358:
2.7 TEST-PLUG KITS A. Manufacturers
Page 359 and 360:
C. Pressure gages at suction and di
Page 361 and 362:
Project No.: 10145 550 15 th Street
Page 363 and 364:
full-port stainless steel ball and
Page 365 and 366:
G. Manual reset safety shut-off val
Page 367 and 368:
piping. Butterfly valves shall be i
Page 369 and 370:
PART 1 - GENERAL 1.01 DESCRIPTION O
Page 371 and 372:
C. Adjustable Swivel Rings: MSS Typ
Page 373 and 374:
2.04 SADDLES AND THERMAL SHIELD INS
Page 375 and 376:
A. Hangers for single pipes shall b
Page 377 and 378:
Page 379 and 380:
2. 2” to 24” from the outlets o
Page 381 and 382:
A. Hanger Adjustment: Adjust hanger
Page 383 and 384:
A. Product Data: Submit manufacture
Page 385 and 386:
Page 387 and 388:
Page 389 and 390:
A. Examine areas and conditions und
Page 391 and 392:
e preset with a shear pin to allow
Page 393 and 394:
Page 395 and 396:
Page 397 and 398:
Page 399 and 400:
3.04 UNDERGROUND PIPING IDENTIFICAT
Page 401 and 402:
Page 403 and 404:
B. Specification “B”, Cellular
Page 405 and 406:
Page 407 and 408:
F. Maintain integrity of vapor barr
Page 409 and 410:
Provide removable insulation for ho
Page 411 and 412:
E. Submit data on Joining Materials
Page 413 and 414:
Material Group: Group 1.1. End Conn
Page 415 and 416:
piping and any other service not re
Page 417 and 418:
Page 419 and 420:
5. Install piping at right angles,
Page 421 and 422:
2. Slope condensate lines minimum 1
Page 423 and 424:
C. All branch outlets shall be made
Page 425 and 426:
3. Waste, Drain and Vent Piping: Al
Page 427 and 428:
3.11 COMMISSIONING: 4. Introduce ch
Page 429 and 430:
1.04 QUALITY ASSURANCE: 5. Maintena
Page 431 and 432:
a. Powers b. Leonard c. Rada d. Apo
Page 433 and 434:
I. Backflow Preventer for carbonate
Page 435 and 436:
B. Shut-off Valves: Install shut-of
Page 437 and 438:
2. Use the purging and disinfecting
Page 439 and 440:
C. Certification of Pump Performanc
Page 441 and 442:
Page 443 and 444:
B. Access: Provide access space aro
Page 445 and 446:
Page 447 and 448:
3.03 FIELD QUALITY CONTROL: A. Test
Page 449 and 450:
PART 2 - PRODUCTS 2.01 ACCEPTABLE M
Page 451 and 452:
Page 453 and 454:
1. Drainage Piping Specialties, inc
Page 455 and 456:
C. Non-Metallic Trench Drains: Poly
Page 457 and 458:
D. Cleanouts Covers: Install floor
Page 459 and 460:
C. Exposed ABS or PVC Piping: Prote
Page 461 and 462:
y the AGA and shall have approval o
Page 463 and 464:
1.04 PRODUCT DELIVERY, STORAGE, AND
Page 465 and 466:
C. Water Piping: Provide piping as
Page 467 and 468:
Woodwork shop drawings specified in
Page 469 and 470:
2.03 FITTINGS, TRIM, AND ACCESSORIE
Page 471 and 472:
A. Remove all labels, and clean fix
Page 473 and 474:
Page 475 and 476:
Page 477 and 478:
L. Install all mechanical equipment
Page 479 and 480:
1.16 MATERIALS AND MANUFACTURERS: A
Page 481 and 482:
Page 483 and 484:
D. Submit this listing as a part of
Page 485 and 486:
1.29 SCHEMATIC FLOW DIAGRAM: Projec
Page 487 and 488:
Page 489 and 490:
ITEM Project No.: 10145 550 15 th S
Page 491 and 492:
AIR CLEANING X X X X METAL DUCTWORK
Page 493 and 494:
E. Coordination with Electrical Wor
Page 495 and 496:
Page 497 and 498:
2.04 STARTERS: A. Furnish individua
Page 499 and 500:
Page 501 and 502:
2.06 BYPASS PANEL: 9. Provide with
Page 503 and 504:
A. After installation is complete,
Page 505 and 506:
Page 507 and 508:
. Flexicraft Industries. c. Flex Pr
Page 509 and 510:
2. Standards: ASTM F 1120 and EJMA'
Page 511 and 512:
PART 3 - EXECUTION a. Bonding Mater
Page 513 and 514:
Page 515 and 516:
D. Install sleeves for pipes passin
Page 517 and 518:
Page 519 and 520:
Page 521 and 522:
f. Weiss Instruments, Inc. g. Winte
Page 523 and 524:
2.8 TEST-PLUG KITS A. Manufacturers
Page 525 and 526:
3. Flow Range: Sensor and indicator
Page 527 and 528:
P. Install differential-pressure-ty
Page 529 and 530:
3.9 THERMAL-ENERGY METER SCHEDULE A
Page 531 and 532:
Page 533 and 534:
B. Ball Valves - 1-1/4” through 2
Page 535 and 536:
E. Solenoid enclosures shall meet t
Page 537 and 538:
D. Examine threads on both the valv
Page 539 and 540:
D. Open gate and globe valves to fu
Page 541 and 542:
Page 543 and 544:
C. Adjustable Swivel Rings: MSS Typ
Page 545 and 546:
2.04 SADDLES AND THERMAL SHIELD INS
Page 547 and 548:
A. Hangers for single pipes shall b
Page 549 and 550:
Page 551 and 552:
2. 2” to 24” from the outlets o
Page 553 and 554:
A. Hanger Adjustment: Adjust hanger
Page 555 and 556:
A. Manufacturer's Qualifications: F
Page 557 and 558:
Page 559 and 560:
Page 561 and 562:
PART 3 - EXECUTION 3.01 INSPECTION:
Page 563 and 564:
to equipment located in basements a
Page 565 and 566:
A. Upon completion of vibration iso
Page 567 and 568:
PART 2 - PRODUCTS 2.01 MANUFACTURER
Page 569 and 570:
B. Provide multi-ply tape consistin
Page 571 and 572:
Page 573 and 574:
A. Adjusting: Relocate any mechanic
Page 575 and 576:
Page 577 and 578:
2.01 BELTS, SHEAVES, IMPELLERS: A.
Page 579 and 580:
Page 581 and 582:
1. On outdoor units, verify that po
Page 583 and 584:
E. Heat Exchangers: 1. Balance, mea
Page 585 and 586:
1. Coordinate balance process with
Page 587 and 588:
Page 589 and 590:
Insulation shall have jacket with t
Page 591 and 592:
A. Examine areas and conditions und
Page 593 and 594:
HVAC Supply - exposed to view HVAC
Page 595 and 596:
I. Cover valves, fittings and simil
Page 597 and 598:
A. General: Install equipment therm
Page 599 and 600:
Page 601 and 602:
PART 2 - PRODUCTS 2.01 MANUFACTURER
Page 603 and 604:
B-15.21). Provide materials that wi
Page 605 and 606:
2.12 SPECIALTIES: A. Foot Valve: Si
Page 607 and 608:
3.03 PIPE APPLICATIONS: A. Use stee
Page 609 and 610:
3.06 VALVE APPLICATIONS: A. General
Page 611 and 612:
Page 613 and 614:
A. Handling Flammable Liquids: Remo
Page 615 and 616:
F. Gas Safety Valves: Gas safety va
Page 617 and 618:
A. General: The Drawings indicate v
Page 619 and 620:
Page 621 and 622:
G. Soldering and brazing materials
Page 623 and 624:
G. Wrought-Copper Solder-Joint Drai
Page 625 and 626:
1. Ductile Iron: ASTM A-536. 2. Fab
Page 627 and 628:
Project No.: 10145 550 15th Street
Page 629 and 630:
accessible location and anchor to a
Page 631 and 632:
3. Before and after piping fabricat
Page 633 and 634:
shall be the products of a single m
Page 635 and 636:
3.07 UNDERGROUND PIPE INSTALLATION:
Page 637 and 638:
3.11 COMMISSIONING: 8. Furnish a co
Page 639 and 640:
5. National Electrical Manufacturer
Page 641 and 642:
A. General: Provide frame-mounted b
Page 643 and 644:
B. After alignment is correct, tigh
Page 645 and 646:
B. Medium or High Pressure Duct: Du
Page 647 and 648:
B. Sheet Metal: Except as otherwise
Page 649 and 650:
adhesive, and fasten with mechanica
Page 651 and 652:
D. Inserts: Install concrete insert
Page 653 and 654:
Page 655 and 656:
B. Shop Drawings: Submit manufactur
Page 657 and 658:
B. Low Pressure Round Dampers (less
Page 659 and 660:
1. Damper Blade Assembly: Curtain T
Page 661 and 662:
Flexmaster "Inspector Series Spin D
Page 663 and 664:
3.04 ADJUSTING AND CLEANING: A. Adj
Page 665 and 666:
1.03 SUBMITTALS: 6. Nationally Reco
Page 667 and 668:
2.02 FANS, GENERAL: 6. Vaneaxial Fa
Page 669 and 670:
B. Housings: Fabricated from heavy-
Page 671 and 672:
C. Fan Wheel: Steel hub and blades.
Page 673 and 674:
A. Upon completion of installation
Page 675 and 676:
Page 677 and 678:
2.02 AIR TERMINALS: Project No.: 10
Page 679 and 680:
3.03 INSTALLATION OF AIR TERMINALS:
Page 681 and 682:
1. Data sheet for each type of air
Page 683 and 684:
E. Dampers: Opposed blade volume da
Page 685 and 686:
Page 687 and 688:
C. Service Access: The boilers shal
Page 689 and 690:
2.4 MOTORS 5. Probe type low water
Page 691 and 692:
D. Ensure pumps operate properly. E
Page 693 and 694:
1. Basis for Certification: Indicat
Page 695 and 696:
7. Tightening bolts shall be equipp
Page 697 and 698:
2.5 PREPARATION FOR SHIPMENT A. All
Page 699 and 700:
Page 701 and 702:
2.02 FAN-COIL UNITS: A. General: Pr
Page 703 and 704:
Page 705 and 706:
2.02 UNIT HEATERS: Project No.: 101
Page 707 and 708:
F. Protect units with protective co
Page 709 and 710:
1. Detail equipment assemblies and
Page 711 and 712:
B. Construction shall be modular, c
Page 713 and 714:
1. Space Air Temperature 2. Space R
Page 715 and 716:
1. When the compressor is running i
Page 717 and 718:
G. Duct installation requirements a
Page 719 and 720:
Page 721 and 722:
C. Feeders Concealed in Ceilings, W
Page 723 and 724:
Page 725 and 726:
2.5 GROUNDING ELECTRODES A. Ground
Page 727 and 728:
E. Bonding Straps and Jumpers: Inst
Page 729 and 730:
Page 731 and 732:
Page 733 and 734:
3.4 CONCRETE BASES A. Construct con
Page 735 and 736:
10. Thomas & Betts Corporation. 11.
Page 737 and 738:
C. Fittings and Accessories: Includ
Page 739 and 740:
12. RACO; Hubbell. 13. Robroy Indus
Page 741 and 742:
d. Nordic Fiberglass, Inc. e. Oldca
Page 743 and 744:
I. Raceway Terminations at Location
Page 745 and 746:
5. Install manufactured rigid steel
Page 747 and 748:
a. For sleeve cross-section rectang
Page 749 and 750:
F. Aboveground, Exterior-Wall Penet
Page 751 and 752:
D. Install identifying devices befo
Page 753 and 754:
1. Labeling Instructions: a. Indoor
Page 755 and 756:
3. Contact Rating: 30-A inductive o
Page 757 and 758:
C. PIR Type: Ceiling mounted; detec
Page 759 and 760:
1. Current Rating for Switching: Li
Page 761 and 762:
3.6 DEMONSTRATION A. Coordinate dem
Page 763 and 764:
1.4 CLOSEOUT SUBMITTALS A. Sustaina
Page 765 and 766:
B. Tech Support Project No.: 10145
Page 767 and 768:
PART 2 - PRODUCTS 2.1 MANUFACTURERS
Page 769 and 770:
3.3 CONNECTIONS A. Ground equipment
Page 771 and 772:
B. Product Selection for Restricted
Page 773 and 774:
4. Feed-Through Lugs: Compression t
Page 775 and 776:
1. Eaton Electrical Inc.; Cutler-Ha
Page 777 and 778:
D. Mount top of trim 90 inches abov
Page 779 and 780:
Page 781 and 782:
B. Tamper-Resistant Convenience Rec
Page 783 and 784:
Page 785 and 786:
E. Toggle Switches, Square Face, 12
Page 787 and 788:
2.12 WALL PLATES A. Single and comb
Page 789 and 790:
6. Tighten unused terminal screws o
Page 791 and 792:
PART 2 - PRODUCTS 2.1 MANUFACTURERS
Page 793 and 794:
Page 795 and 796:
B. Type GD, General Duty, Single Th
Page 797 and 798:
4. Mechanically interlocked auxilia
Page 799 and 800:
11. Accessory Control Power Voltage
Page 801 and 802:
Page 803 and 804:
1.6 CLOSEOUT SUBMITTALS A. Operatio
Page 805 and 806:
4. Sound Rating: Class A. 5. Total
Page 807 and 808:
Page 809 and 810:
PART 3 - EXECUTION 3.1 INSTALLATION
Page 811 and 812:
Page 813 and 814:
1.7 CLOSEOUT SUBMITTALS A. Operatio
Page 815 and 816:
L. Luminaire Finish: Manufacturer's
Page 817 and 818:
C. High-Pressure Sodium Ballasts: E
Page 819 and 820:
J. Prime-Coat Finish: Manufacturer'
Page 821 and 822:
3. With cord opening. 4. With locka
Page 823:
3.8 DEMONSTRATION A. Train Owner's
show all

substitution request - Alliance Construction Solutions

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?