substitution request - Alliance Construction Solutions

Recommendations

Info

B. Install escutcheons with ID to closely fit around pipe, tube, and insulation of piping and with OD that completely covers opening. C. Furnish pipe Escutcheons with nickel or chrome finish for occupied areas, prime paint finish for unoccupied areas. D. Escutcheons for Moist Areas: Provide cast brass or sheet brass, solid or split hinged. E. Install floor plates for piping penetrations of equipment-room floors. F. Install floor plates with ID to closely fit around pipe, tube, and insulation of piping and with OD that completely covers opening. 1. New Piping: One-piece, floor-plate type. 2. Existing Piping: Split-casting, floor-plate type. 3.2 FIELD QUALITY CONTROL A. Replace broken and damaged escutcheons and floor plates using new materials. Project No.: 10145 550 15 th Street Dual Brand Hotel 03/16/2012 END OF SECTION 22 0518 22 0518 - 2 ESCUTCHEONS FOR PLUMBING PIPING
PART 1 - GENERAL 1.1 RELATED DOCUMENTS Project No.: 10145 550 15 th Street Dual Brand Hotel 03/16/2012 SECTION 22 0519 METERS AND GAGES FOR PLUMBING PIPING A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this Section. 1.2 SUMMARY A. Section Includes: 1. Bimetallic-actuated thermometers. 2. Liquid-in-glass thermometers. 3. Thermowells. 4. Dial-type pressure gages. 5. Gage attachments. 6. Test plugs. 7. Test-plug kits. B. Related Sections: 1. Section 221113 "Facility Water Distribution Piping" for domestic water meters and combined domestic and fire-protection water-service meters outside the building. 2. Section 221116 "Domestic Water Piping" for water meters inside the building. 1.3 ACTION SUBMITTALS A. Product Data: For each type of product indicated. 1.4 INFORMATIONAL SUBMITTALS A. Product Certificates: For each type of meter and gage, from manufacturer. 1.5 CLOSEOUT SUBMITTALS A. Operation and Maintenance Data: For meters and gages to include in operation and maintenance manuals. 22 0519 - 1 METERS AND GAGES FOR PLUMBING PIPING
Page 1 and 2:
TECHNICAL SPECIFICATIONS FOR HOMEWO
Page 3 and 4:
DIVISION 06 - WOOD AND PLASTICS Sec
Page 5 and 6:
Division Section Title Pages DIVISI
Page 7 and 8:
Division Section Title Pages DIVISI
Page 9 and 10:
B. Type of Contract: 1. Project wil
Page 11 and 12:
PART 1 - GENERAL 1.1 SUMMARY SECTIO
Page 13 and 14:
c. Requested substitution has recei
Page 15 and 16:
SUBSTITUTION REQUEST (Continued) Th
Page 17 and 18:
2. Include a list of quantities of
Page 19 and 20:
a. Include separate line items unde
Page 21 and 22:
8. Final meter readings for utiliti
Page 23 and 24:
1.4 COORDINATION DRAWINGS A. Coordi
Page 25 and 26:
1. Project name. 2. Name and addres
Page 27 and 28:
9) Progress cleaning. 10) Quality a
Page 29 and 30:
PART 2 - PRODUCTS 2.1 CONTRACTOR'S
Page 31 and 32:
Page 33 and 34:
2. Intermediate Review: If intermed
Page 35 and 36:
1. If information must be specially
Page 37 and 38:
PART 3 - EXECUTION 3.1 CONTRACTOR'S
Page 39 and 40:
jurisdiction, to establish product
Page 41 and 42:
1.7 QUALITY ASSURANCE A. General: Q
Page 43 and 44:
1.9 SPECIAL TESTS AND INSPECTIONS A
Page 45 and 46:
1.5 PROJECT CONDITIONS A. Temporary
Page 47 and 48:
J. Electronic Communication Service
Page 49 and 50:
procedures to be followed. Instruct
Page 51 and 52:
proposed comparable product request
Page 53 and 54:
with requirements. Comparable produ
Page 55 and 56:
PART 2 - PRODUCTS 2.1 MATERIALS A.
Page 57 and 58:
F. Tools and Equipment: Do not use
Page 59 and 60:
1. Remove liquid spills promptly. 2
Page 61 and 62:
4. Submit maintenance material subm
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
paper; with clear plastic sleeve on
Page 69 and 70:
Page 71 and 72:
2.4 MISCELLANEOUS RECORD SUBMITTALS
Page 73 and 74:
E. Utility Service: Maintain existi
Page 75 and 76:
D. Existing Items to Remain: Protec
Page 77 and 78:
C. Verification Samples: For each p
Page 79 and 80:
B. Geo-Synthetic Fill fill shall be
Page 81 and 82:
F. Preinstallation Conference: Cond
Page 83 and 84:
F. Clear, Solvent-Borne, Membrane-F
Page 85 and 86:
2. Sawed Joints: Form contraction j
Page 87 and 88:
3.09 CONCRETE PROTECTING AND CURING
Page 89 and 90:
3.12 FIELD QUALITY CONTROL A. Testi
Page 91 and 92:
PART 1 - GENERAL 1.01 SUMMARY A. Se
Page 93 and 94:
2.03 MASONRY LINTELS A. Masonry Lin
Page 95 and 96:
2.07 MISCELLANEOUS MASONRY ACCESSOR
Page 97 and 98:
C. Joints: 1. For bed joints, do no
Page 99 and 100:
3.08 FIELD QUALITY CONTROL A. Testi
Page 101 and 102:
PART 1 - GENERAL 1.01 SUMMARY SECTI
Page 103 and 104:
1. Finish: Plain or Hot-dip zinc co
Page 105 and 106:
3.02 ERECTION A. Set structural ste
Page 107 and 108:
PART 1 - GENERAL 1.01 SUMMARY A. Th
Page 109 and 110:
2.03 NONCOMPOSITE FORM DECK A. Nonc
Page 111 and 112:
D. Remove and replace work that doe
Page 113 and 114:
Page 115 and 116:
D. Sealer Gaskets: Closed-cell neop
Page 117 and 118:
J. Install miscellaneous framing an
Page 119 and 120:
PART 1- GENERAL 1.1 SUMMARY SECTION
Page 121 and 122:
paint systems indicated, and for ca
Page 123 and 124:
2.12 PIPE BOLLARDS mitered joints f
Page 125 and 126:
Page 127 and 128:
B. Apply bituminous paint to concea
Page 129 and 130:
B. Welded Connections: Fabricate ra
Page 131 and 132:
PART 1 - GENERAL 1.1 SUMMARY A. Thi
Page 133 and 134:
Page 135 and 136:
F. Granite Countertops: With bull n
Page 137 and 138:
G. Solid Lumber: Dry, sound, select
Page 139 and 140:
E. Anchor woodwork to anchors or bl
Page 141 and 142:
PART 2 - PRODUCTS A. Tub / Shower S
Page 143 and 144:
2.2 ACCESSORIES A. Trim Accessories
Page 145 and 146:
D. Protection Course: ASTM D 6506,
Page 147 and 148:
1.5 DELIVERY, STORAGE, AND HANDLING
Page 149 and 150:
etarder to cover miscellaneous void
Page 151 and 152:
1. Basis-of-Design Product: Subject
Page 153 and 154:
C. Accessory Installation: Install
Page 155 and 156:
PART 2 - PRODUCTS 2.01 EPDM ROOFING
Page 157 and 158:
B. Install tapered insulation under
Page 159 and 160:
B. Sheet Metal Standard for Flashin
Page 161 and 162:
2.05 ROOF-DRAINAGE SHEET METAL FABR
Page 163 and 164:
D. Pipe or Post Counterflashing: In
Page 165 and 166:
PART 3 - EXECUTION 3.01 PREPARATION
Page 167 and 168:
2.02 PENETRATION FIRESTOPPING A. Pr
Page 169 and 170:
Page 171 and 172:
2. Characteristics: Single-componen
Page 173 and 174:
PART 3 - EXECUTION 3.1 PREPARATION
Page 175 and 176:
Page 177 and 178:
E. Inserts, Bolts, and Fasteners: H
Page 179 and 180:
2.5 FABRICATION A. Fabricate hollow
Page 181 and 182:
3.2 PREPARATION A. Remove welded-in
Page 183 and 184:
Page 185 and 186:
1. Install fire-rated doors accordi
Page 187 and 188:
C. Steel Finishes: Comply with NAAM
Page 189 and 190:
Page 191 and 192:
C. Glass: Provide manufacturer’s
Page 193 and 194:
PART 1 - GENERAL 1.1 SUMMARY A. Sec
Page 195 and 196:
1.6 PROJECT CONDITIONS A. Field Mea
Page 197 and 198:
a. Accessible Doors: Smooth surface
Page 199 and 200:
G. After fabrication, clearly mark
Page 201 and 202:
Page 203 and 204:
E. Emergency-Exit Door Requirements
Page 205 and 206:
. Adjustable opening and closing sp
Page 207 and 208:
. Reinforce members as required to
Page 209 and 210:
G. Wiring within Automatic Entrance
Page 211 and 212:
1.3 QUALITY ASSURANCE A. Source Lim
Page 213 and 214:
2. Interior Hinges: Steel, with ste
Page 215 and 216:
D. Panic Exit Devices: Listed and l
Page 217 and 218:
B. Combination Overhead Stops and H
Page 219 and 220:
C. Door Viewer: 200 degree door vie
Page 221 and 222:
Door Hardware Set No. 6 Exterior St
Page 223 and 224:
1 Protective Trim Units Kick Plate
Page 225 and 226:
Door Hardware Set No. 25 Pool Publi
Page 227 and 228:
10. Latch bolt operated by inside l
Page 229 and 230:
surface temperatures of materials d
Page 231 and 232:
3. Spacer Specifications: Manufactu
Page 233 and 234:
3.2 PREPARATION A. Clean glazing ch
Page 235 and 236:
Page 237 and 238:
2.2 MISCELLANEOUS MATERIALS A. Sett
Page 239 and 240:
Page 241 and 242:
C. Fabricate frames, including inte
Page 243 and 244:
Page 245 and 246:
Page 247 and 248:
2. Foam Gasket: Adhesive-backed, cl
Page 249 and 250:
Page 251 and 252:
3.03 INSTALLING ACCESSORIES A. Inst
Page 253 and 254:
C. Flexible Gypsum Board: ASTM C 13
Page 255 and 256:
F. Install trim with back flanges i
Page 257 and 258:
1.5 QUALITY ASSURANCE A. Source Lim
Page 259 and 260:
B. Standard Cement Grout: ANSI A118
Page 261 and 262:
3.3 TILE INSTALLATION A. Comply wit
Page 263 and 264:
Page 265 and 266:
mold, mildew, or bacterial growth w
Page 267 and 268:
3.3 INSTALLATION A. General: Instal
Page 269 and 270:
1.6 WARRANTY A. Special Warranty: M
Page 271 and 272:
Page 273 and 274:
Page 275 and 276:
Page 277 and 278:
F. Subfloor Alkalinity Conditions:
Page 279 and 280:
I. The final carpet pattern, layout
Page 281 and 282:
Page 283 and 284:
3.4 CLEANING A. Remove excess adhes
Page 285 and 286:
1.5 PROJECT CONDITIONS A. Apply pai
Page 287 and 288:
E. Galvanized-Metal Substrates: Rem
Page 289 and 290:
Page 291 and 292:
C. Quick-Drying Primer for Aluminum
Page 293 and 294:
B. If undercoats or other condition
Page 295 and 296:
Page 297 and 298:
PART 3 - EXECUTION 3.01 EXAMINATION
Page 299 and 300:
Page 301 and 302: PART 3 - EXECUTION 3.1 INSTALLATION
Page 303 and 304: 1.5 EXTRA MATERIALS A. Furnish extr
Page 305 and 306: 3.4 CLEANING A. Immediately after c
Page 307 and 308: PART 2 - PRODUCTS 2.1 ACCESSORY SCH
Page 309 and 310: 3.2 ADJUSTING AND CLEANING A. Adjus
Page 311 and 312: PART 1 - GENERAL 1.1 SUMMARY A. Sec
Page 313 and 314: 2.3 FABRICATION A. Fire Protection
Page 315 and 316: PART 1 - GENERAL 1.1 SUMMARY SECTIO
Page 317 and 318: PART 1 - GENERAL 1.1 SUMMARY A. Thi
Page 319 and 320: B. Locker Arrangement: Double tier.
Page 321 and 322: C. Surface Preparation: Clean surfa
Page 323 and 324: PART 1 - GENERAL 1.1 SUMMARY SECTIO
Page 325 and 326: PART 1 - GENERAL 1.1 SUBMITTALS SEC
Page 327 and 328: B. Microwave Oven: 1. HWS Basis-of-
Page 329 and 330: PART 1 - GENERAL 1.01 SUMMARY SECTI
Page 331 and 332: PART 1 - GENERAL 1.1 SUMMARY A. Thi
Page 333 and 334: 1.1 SUMMARY SECTION 13 1500 SWIMMIN
Page 335 and 336: 2.02 CHUTES A. Chute Metal: Aluminu
Page 337 and 338: PART 1 - GENERAL 1.1 RELATED DOCUME
Page 339 and 340: 2.5 SINGLE-PHASE MOTORS A. Motors l
Page 341 and 342: B. Product Certificates: For each t
Page 343 and 344: C. Rubber Packless Expansion Joints
Page 345 and 346: B. Install metal-bellows expansion
Page 347 and 348: PART 1 - GENERAL 1.1 RELATED DOCUME
Page 349 and 350: D. Install sleeves for pipes passin
Page 351: PART 1 - GENERAL 1.1 RELATED DOCUME
Page 355 and 356: d. Tel-Tru Manufacturing Company. e
Page 357 and 358: 2.7 TEST-PLUG KITS A. Manufacturers
Page 359 and 360: C. Pressure gages at suction and di
Page 361 and 362: Project No.: 10145 550 15 th Street
Page 363 and 364: full-port stainless steel ball and
Page 365 and 366: G. Manual reset safety shut-off val
Page 367 and 368: piping. Butterfly valves shall be i
Page 369 and 370: PART 1 - GENERAL 1.01 DESCRIPTION O
Page 371 and 372: C. Adjustable Swivel Rings: MSS Typ
Page 373 and 374: 2.04 SADDLES AND THERMAL SHIELD INS
Page 375 and 376: A. Hangers for single pipes shall b
Page 379 and 380: 2. 2” to 24” from the outlets o
Page 381 and 382: A. Hanger Adjustment: Adjust hanger
Page 383 and 384: A. Product Data: Submit manufacture
Page 389 and 390: A. Examine areas and conditions und
Page 391 and 392: e preset with a shear pin to allow
Page 399 and 400: 3.04 UNDERGROUND PIPING IDENTIFICAT
Page 403 and 404:
B. Specification “B”, Cellular
Page 405 and 406:
Project No.: 10145 550 15 th Street
Page 407 and 408:
F. Maintain integrity of vapor barr
Page 409 and 410:
Provide removable insulation for ho
Page 411 and 412:
E. Submit data on Joining Materials
Page 413 and 414:
Material Group: Group 1.1. End Conn
Page 415 and 416:
piping and any other service not re
Page 417 and 418:
Page 419 and 420:
5. Install piping at right angles,
Page 421 and 422:
2. Slope condensate lines minimum 1
Page 423 and 424:
C. All branch outlets shall be made
Page 425 and 426:
3. Waste, Drain and Vent Piping: Al
Page 427 and 428:
3.11 COMMISSIONING: 4. Introduce ch
Page 429 and 430:
1.04 QUALITY ASSURANCE: 5. Maintena
Page 431 and 432:
a. Powers b. Leonard c. Rada d. Apo
Page 433 and 434:
I. Backflow Preventer for carbonate
Page 435 and 436:
B. Shut-off Valves: Install shut-of
Page 437 and 438:
2. Use the purging and disinfecting
Page 439 and 440:
C. Certification of Pump Performanc
Page 441 and 442:
Page 443 and 444:
B. Access: Provide access space aro
Page 445 and 446:
PART 1 - GENERAL 1.01 DESCRIPTION O
Page 447 and 448:
3.03 FIELD QUALITY CONTROL: A. Test
Page 449 and 450:
PART 2 - PRODUCTS 2.01 ACCEPTABLE M
Page 451 and 452:
Page 453 and 454:
1. Drainage Piping Specialties, inc
Page 455 and 456:
C. Non-Metallic Trench Drains: Poly
Page 457 and 458:
D. Cleanouts Covers: Install floor
Page 459 and 460:
C. Exposed ABS or PVC Piping: Prote
Page 461 and 462:
y the AGA and shall have approval o
Page 463 and 464:
1.04 PRODUCT DELIVERY, STORAGE, AND
Page 465 and 466:
C. Water Piping: Provide piping as
Page 467 and 468:
Woodwork shop drawings specified in
Page 469 and 470:
2.03 FITTINGS, TRIM, AND ACCESSORIE
Page 471 and 472:
A. Remove all labels, and clean fix
Page 473 and 474:
Page 475 and 476:
Page 477 and 478:
L. Install all mechanical equipment
Page 479 and 480:
1.16 MATERIALS AND MANUFACTURERS: A
Page 481 and 482:
Page 483 and 484:
D. Submit this listing as a part of
Page 485 and 486:
1.29 SCHEMATIC FLOW DIAGRAM: Projec
Page 487 and 488:
Page 489 and 490:
ITEM Project No.: 10145 550 15 th S
Page 491 and 492:
AIR CLEANING X X X X METAL DUCTWORK
Page 493 and 494:
E. Coordination with Electrical Wor
Page 495 and 496:
Page 497 and 498:
2.04 STARTERS: A. Furnish individua
Page 499 and 500:
Page 501 and 502:
2.06 BYPASS PANEL: 9. Provide with
Page 503 and 504:
A. After installation is complete,
Page 505 and 506:
PART 1 - GENERAL 1.1 RELATED DOCUME
Page 507 and 508:
. Flexicraft Industries. c. Flex Pr
Page 509 and 510:
2. Standards: ASTM F 1120 and EJMA'
Page 511 and 512:
PART 3 - EXECUTION a. Bonding Mater
Page 513 and 514:
Page 515 and 516:
D. Install sleeves for pipes passin
Page 517 and 518:
Page 519 and 520:
Page 521 and 522:
f. Weiss Instruments, Inc. g. Winte
Page 523 and 524:
2.8 TEST-PLUG KITS A. Manufacturers
Page 525 and 526:
3. Flow Range: Sensor and indicator
Page 527 and 528:
P. Install differential-pressure-ty
Page 529 and 530:
3.9 THERMAL-ENERGY METER SCHEDULE A
Page 531 and 532:
Page 533 and 534:
B. Ball Valves - 1-1/4” through 2
Page 535 and 536:
E. Solenoid enclosures shall meet t
Page 537 and 538:
D. Examine threads on both the valv
Page 539 and 540:
D. Open gate and globe valves to fu
Page 541 and 542:
Page 543 and 544:
C. Adjustable Swivel Rings: MSS Typ
Page 545 and 546:
2.04 SADDLES AND THERMAL SHIELD INS
Page 547 and 548:
A. Hangers for single pipes shall b
Page 549 and 550:
Page 551 and 552:
2. 2” to 24” from the outlets o
Page 553 and 554:
A. Hanger Adjustment: Adjust hanger
Page 555 and 556:
A. Manufacturer's Qualifications: F
Page 557 and 558:
Page 559 and 560:
Page 561 and 562:
PART 3 - EXECUTION 3.01 INSPECTION:
Page 563 and 564:
to equipment located in basements a
Page 565 and 566:
A. Upon completion of vibration iso
Page 567 and 568:
PART 2 - PRODUCTS 2.01 MANUFACTURER
Page 569 and 570:
B. Provide multi-ply tape consistin
Page 571 and 572:
Page 573 and 574:
A. Adjusting: Relocate any mechanic
Page 575 and 576:
Page 577 and 578:
2.01 BELTS, SHEAVES, IMPELLERS: A.
Page 579 and 580:
Page 581 and 582:
1. On outdoor units, verify that po
Page 583 and 584:
E. Heat Exchangers: 1. Balance, mea
Page 585 and 586:
1. Coordinate balance process with
Page 587 and 588:
Page 589 and 590:
Insulation shall have jacket with t
Page 591 and 592:
A. Examine areas and conditions und
Page 593 and 594:
HVAC Supply - exposed to view HVAC
Page 595 and 596:
I. Cover valves, fittings and simil
Page 597 and 598:
A. General: Install equipment therm
Page 599 and 600:
Page 601 and 602:
PART 2 - PRODUCTS 2.01 MANUFACTURER
Page 603 and 604:
B-15.21). Provide materials that wi
Page 605 and 606:
2.12 SPECIALTIES: A. Foot Valve: Si
Page 607 and 608:
3.03 PIPE APPLICATIONS: A. Use stee
Page 609 and 610:
3.06 VALVE APPLICATIONS: A. General
Page 611 and 612:
Page 613 and 614:
A. Handling Flammable Liquids: Remo
Page 615 and 616:
F. Gas Safety Valves: Gas safety va
Page 617 and 618:
A. General: The Drawings indicate v
Page 619 and 620:
Page 621 and 622:
G. Soldering and brazing materials
Page 623 and 624:
G. Wrought-Copper Solder-Joint Drai
Page 625 and 626:
1. Ductile Iron: ASTM A-536. 2. Fab
Page 627 and 628:
Project No.: 10145 550 15th Street
Page 629 and 630:
accessible location and anchor to a
Page 631 and 632:
3. Before and after piping fabricat
Page 633 and 634:
shall be the products of a single m
Page 635 and 636:
3.07 UNDERGROUND PIPE INSTALLATION:
Page 637 and 638:
3.11 COMMISSIONING: 8. Furnish a co
Page 639 and 640:
5. National Electrical Manufacturer
Page 641 and 642:
A. General: Provide frame-mounted b
Page 643 and 644:
B. After alignment is correct, tigh
Page 645 and 646:
B. Medium or High Pressure Duct: Du
Page 647 and 648:
B. Sheet Metal: Except as otherwise
Page 649 and 650:
adhesive, and fasten with mechanica
Page 651 and 652:
D. Inserts: Install concrete insert
Page 653 and 654:
Page 655 and 656:
B. Shop Drawings: Submit manufactur
Page 657 and 658:
B. Low Pressure Round Dampers (less
Page 659 and 660:
1. Damper Blade Assembly: Curtain T
Page 661 and 662:
Flexmaster "Inspector Series Spin D
Page 663 and 664:
3.04 ADJUSTING AND CLEANING: A. Adj
Page 665 and 666:
1.03 SUBMITTALS: 6. Nationally Reco
Page 667 and 668:
2.02 FANS, GENERAL: 6. Vaneaxial Fa
Page 669 and 670:
B. Housings: Fabricated from heavy-
Page 671 and 672:
C. Fan Wheel: Steel hub and blades.
Page 673 and 674:
A. Upon completion of installation
Page 675 and 676:
Page 677 and 678:
2.02 AIR TERMINALS: Project No.: 10
Page 679 and 680:
3.03 INSTALLATION OF AIR TERMINALS:
Page 681 and 682:
1. Data sheet for each type of air
Page 683 and 684:
E. Dampers: Opposed blade volume da
Page 685 and 686:
Page 687 and 688:
C. Service Access: The boilers shal
Page 689 and 690:
2.4 MOTORS 5. Probe type low water
Page 691 and 692:
D. Ensure pumps operate properly. E
Page 693 and 694:
1. Basis for Certification: Indicat
Page 695 and 696:
7. Tightening bolts shall be equipp
Page 697 and 698:
2.5 PREPARATION FOR SHIPMENT A. All
Page 699 and 700:
Page 701 and 702:
2.02 FAN-COIL UNITS: A. General: Pr
Page 703 and 704:
Page 705 and 706:
2.02 UNIT HEATERS: Project No.: 101
Page 707 and 708:
F. Protect units with protective co
Page 709 and 710:
1. Detail equipment assemblies and
Page 711 and 712:
B. Construction shall be modular, c
Page 713 and 714:
1. Space Air Temperature 2. Space R
Page 715 and 716:
1. When the compressor is running i
Page 717 and 718:
G. Duct installation requirements a
Page 719 and 720:
Page 721 and 722:
C. Feeders Concealed in Ceilings, W
Page 723 and 724:
Page 725 and 726:
2.5 GROUNDING ELECTRODES A. Ground
Page 727 and 728:
E. Bonding Straps and Jumpers: Inst
Page 729 and 730:
Page 731 and 732:
Page 733 and 734:
3.4 CONCRETE BASES A. Construct con
Page 735 and 736:
10. Thomas & Betts Corporation. 11.
Page 737 and 738:
C. Fittings and Accessories: Includ
Page 739 and 740:
12. RACO; Hubbell. 13. Robroy Indus
Page 741 and 742:
d. Nordic Fiberglass, Inc. e. Oldca
Page 743 and 744:
I. Raceway Terminations at Location
Page 745 and 746:
5. Install manufactured rigid steel
Page 747 and 748:
a. For sleeve cross-section rectang
Page 749 and 750:
F. Aboveground, Exterior-Wall Penet
Page 751 and 752:
D. Install identifying devices befo
Page 753 and 754:
1. Labeling Instructions: a. Indoor
Page 755 and 756:
3. Contact Rating: 30-A inductive o
Page 757 and 758:
C. PIR Type: Ceiling mounted; detec
Page 759 and 760:
1. Current Rating for Switching: Li
Page 761 and 762:
3.6 DEMONSTRATION A. Coordinate dem
Page 763 and 764:
1.4 CLOSEOUT SUBMITTALS A. Sustaina
Page 765 and 766:
B. Tech Support Project No.: 10145
Page 767 and 768:
PART 2 - PRODUCTS 2.1 MANUFACTURERS
Page 769 and 770:
3.3 CONNECTIONS A. Ground equipment
Page 771 and 772:
B. Product Selection for Restricted
Page 773 and 774:
4. Feed-Through Lugs: Compression t
Page 775 and 776:
1. Eaton Electrical Inc.; Cutler-Ha
Page 777 and 778:
D. Mount top of trim 90 inches abov
Page 779 and 780:
Page 781 and 782:
B. Tamper-Resistant Convenience Rec
Page 783 and 784:
Page 785 and 786:
E. Toggle Switches, Square Face, 12
Page 787 and 788:
2.12 WALL PLATES A. Single and comb
Page 789 and 790:
6. Tighten unused terminal screws o
Page 791 and 792:
PART 2 - PRODUCTS 2.1 MANUFACTURERS
Page 793 and 794:
Page 795 and 796:
B. Type GD, General Duty, Single Th
Page 797 and 798:
4. Mechanically interlocked auxilia
Page 799 and 800:
11. Accessory Control Power Voltage
Page 801 and 802:
Page 803 and 804:
1.6 CLOSEOUT SUBMITTALS A. Operatio
Page 805 and 806:
4. Sound Rating: Class A. 5. Total
Page 807 and 808:
Page 809 and 810:
PART 3 - EXECUTION 3.1 INSTALLATION
Page 811 and 812:
Page 813 and 814:
1.7 CLOSEOUT SUBMITTALS A. Operatio
Page 815 and 816:
L. Luminaire Finish: Manufacturer's
Page 817 and 818:
C. High-Pressure Sodium Ballasts: E
Page 819 and 820:
J. Prime-Coat Finish: Manufacturer'
Page 821 and 822:
3. With cord opening. 4. With locka
Page 823:
3.8 DEMONSTRATION A. Train Owner's
show all

substitution request - Alliance Construction Solutions

Create successful ePaper yourself

Delete template?

Save as template?