Navisphere Command Line Interface (CLI) Reference - VMware Communities

More documents

Recommendations

Info

Basic Commandsnetworkadmin -set [-name name][-ipv4 [-address address] [-subnetmask subnetmask] [-gateway gateway-IP-address]][-speed [-duplex]] [-o]networkadmin -set [-name name] [-ipv6 [-automatic | -disable |-manual [-globalprefix prefix] [-gateway gateway -IP-address]][-speed[-duplex]] [-o]PrerequisitesOptionsFor naviseccli, you must have a user account on the storage systemon which you want to execute the command.For navicli, you must have a user entry in the Navisphere agentconfiguration file.-name nameChanges the SPs network name to name. The maximum size of thename is 64 characters.-address IP-addressChanges the SPs IPv4 network address to IP address.-ipv4Specifies the settings for IPv4.-ipv6Specifies the settings for IPv6.-automaticEnables IPv6 on the SP automatically.-disableDisables IPv6 on the SP-manualEnables IPv6 on the SP. The global prefix and gateway must beset manually.-gateway gateway-IP-addressChanges the SP’s IPv4 or IPv6 gateway IP address togateway-IP-address.-subnetmask maskChanges the SPs IPv4 subnet mask to mask.242 EMC Navisphere Command Line Interface (CLI) Reference
Basic Commands-globalprefix prefixChanges the SP’s IPv6 global prefix to prefix.–speed [-duplex] (CX4 series only)Changes the speed on the management port for the target SP.Note: The command switch -speed [-duplex] is supported only onSecure CLI. The Classic CLI does not support this command switch.-oExecutes the command without prompting for confirmation.OutputExampleSee the Description section. If the version of FLARE software runningon the SP does not support this command, a Not supported errormessage is printed to stderr. Other errors:NETADMIN_NOT_FOUNDNETADMIN_INVALID_NAMEInvalid command line parametersInvalid speed requestnaviseccli -h ss1_spa networkadmin -set -gatewayaddressChanging the gateway address of SP A from 123.456.789.011to 123.456.789.011 (y/n)[n] ySP A reboots.For the SP with hostname payroll_storage_SPA this commandchanges the gateway address.Note: To use this command with navicli, replace naviseccli with navicli.naviseccli -address 10.5.2.12 -user a -password a –scope 0networkadmin –set –ipv6 -manualThis command enables IPv6 (if not enabled) and maintains thecurrent settings.naviseccli -address 10.5.2.12 -user a -password a –scope 0networkadmin –set –ipv6 -manual -globalprefix 3ffe:80c0:22c:4c:This command enables IPv6 (if not enabled) and sets the IPv6 globalprefix.243
Page 1 and 2:
EMC ® Navisphere ®Command Line In
Page 3 and 4:
ContentsPreface ...................
Page 5 and 6:
Contentsgetconfig .................
Page 7 and 8:
ContentsEstimating the reserved LUN
Page 9 and 10:
PrefaceAs part of an effort to impr
Page 11 and 12:
PrefaceFor the most current managem
Page 13 and 14:
Invisible Body Tag1About EMC Navisp
Page 15 and 16:
About EMC Navisphere CLITermEvent M
Page 17 and 18:
About EMC Navisphere CLIAbout EMC N
Page 19 and 20:
About EMC Navisphere CLI◆send LUN
Page 21 and 22:
About EMC Navisphere CLIAbout Navis
Page 23 and 24:
About EMC Navisphere CLIThe tradeof
Page 25 and 26:
About EMC Navisphere CLIFigure 1 sh
Page 27 and 28:
About EMC Navisphere CLIConfiguring
Page 29 and 30:
About EMC Navisphere CLISupported o
Page 31 and 32:
About EMC Navisphere CLIWhat next?C
Page 33 and 34:
In2About CLI CommandsThis chapter e
Page 35 and 36:
About CLI CommandsGetting started w
Page 37 and 38:
About CLI CommandsnaviseccliDescrip
Page 39 and 40:
About CLI CommandsNote: When the -n
Page 41 and 42:
About CLI Commands-vEnables verbose
Page 43 and 44:
About CLI CommandsLUN IDs, unique I
Page 45 and 46:
About CLI CommandsnavicliSends stat
Page 47 and 48:
About CLI CommandsSpaces in argumen
Page 49 and 50:
3Basic CommandsThis chapter explain
Page 51 and 52:
Basic Commands◆ managedby .......
Page 53 and 54:
Basic Commandsnaviseccli -h ss1_spa
Page 55 and 56:
Basic CommandsFor SP A (SP hostname
Page 57 and 58:
Basic Commands-oExecutes the comman
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Basic CommandsNote: Duplication wil
Page 65 and 66:
Basic CommandsarraynameDescriptionR
Page 67 and 68:
Basic CommandsNote: If you issue th
Page 69 and 70:
Basic CommandsBus 0 is currently ru
Page 71 and 72:
Basic CommandsExampleThe following
Page 73 and 74:
Basic Commandsbackendbus -get -phys
Page 75 and 76:
Basic CommandsOutput Bus 0Current S
Page 77 and 78:
Basic CommandsPrerequisitesOutputEx
Page 79 and 80:
Basic CommandsbindCreates a LUN wit
Page 81 and 82:
Basic CommandsLUN to bindRAID 3RAID
Page 83 and 84:
Basic CommandsSyntaxPrerequisitesOp
Page 85 and 86:
Basic Commands-elsz stripe-element-
Page 87 and 88:
Basic Commands-v verify-priority (A
Page 89 and 90:
Basic Commandscachecard -initialize
Page 91 and 92:
Basic CommandsOutput Total Memory:
Page 93 and 94:
Basic CommandsSyntaxPrerequisitesOp
Page 95 and 96:
Basic Commands-pf prefetch-type (No
Page 97 and 98:
Basic CommandsThe lower the priorit
Page 99 and 100:
Basic Commands-lex expansion (Not s
Page 101 and 102:
Basic Commandsclassiccli (CX series
Page 103 and 104:
Basic Commandsclearstats (CX series
Page 105 and 106:
Basic Commandscopytohotspare (not s
Page 107 and 108:
Basic CommandsNote: The disks in a
Page 109 and 110:
Basic CommandsemconfigurationDescri
Page 111 and 112:
Basic CommandsFor navicli, you must
Page 113 and 114:
Basic Commands50:06:01:60:90:60:00:
Page 115 and 116:
Basic Commands-d disksDownloads dis
Page 117 and 118:
Basic CommandsExamplesTo turn flash
Page 119 and 120:
Basic CommandsflashledsDescriptionS
Page 121 and 122:
Basic Commands-modelReturns the mod
Page 123 and 124:
Basic CommandsgetallGets comprehens
Page 125 and 126:
Basic Commands-reservedDisplays the
Page 127 and 128:
Basic CommandsDAE/SP Bus 0 Enclosur
Page 129 and 130:
Basic CommandsSP Information-------
Page 131 and 132:
Basic CommandsInformation about eac
Page 133 and 134:
Basic CommandsSample output display
Page 135 and 136:
Basic CommandsSP cache information
Page 137 and 138:
Basic CommandsLUN information (same
Page 139 and 140:
Basic CommandsLOGICAL UNIT NUMBER 1
Page 141 and 142:
Basic CommandsNumber of arrivals wi
Page 143 and 144:
Basic CommandsRemapped Sectors: N/A
Page 145 and 146:
Basic CommandsBus 0 Enclosure 0 Dis
Page 147 and 148:
Basic CommandsHBA/SP Pairs:HBA UID,
Page 149 and 150:
Basic CommandsgetarrayuidDescriptio
Page 151 and 152:
Basic CommandsgetcacheDescriptionSy
Page 153 and 154:
Basic Commands-rstaReturns the curr
Page 155 and 156:
Basic CommandsSPA Optimized Raid 3
Page 157 and 158:
Basic CommandsExamplenaviseccli -h
Page 159 and 160:
Basic Commands-idleReturns the perc
Page 161 and 162:
Basic CommandsgetcrusGets CRU state
Page 163 and 164:
Basic Commands-fanc (Not supported
Page 165 and 166:
Basic Commands-vscaReturns the stat
Page 167 and 168:
Basic CommandsgetdiskGets disk stat
Page 169 and 170:
Basic Commands-busyticksReturns the
Page 171 and 172:
Basic Commands-srReturns the total
Page 173 and 174:
Basic CommandsExample naviseccli -h
Page 175 and 176:
Basic Commands+nDisplays the oldest
Page 177 and 178:
Basic CommandsExample naviseccli -h
Page 179 and 180:
Basic CommandsPrerequisitesOptionsF
Page 181 and 182:
Basic Commands-idleticksReturns the
Page 183 and 184:
Basic Commands-prbReturns the perce
Page 185 and 186:
Basic Commands-sor*Returns the sum
Page 187 and 188:
Basic Commands-whist*Returns write
Page 189 and 190:
Basic CommandsEnclosure 0 Disk 0 Qu
Page 191 and 192: Basic CommandsNote: Classic CLI doe
Page 193 and 194: Basic CommandsSample output of getr
Page 195 and 196: Basic CommandsNote: To use this com
Page 197 and 198: Basic Commands-legalReturns informa
Page 199 and 200: Basic Commandsgetsniffer (CX series
Page 201 and 202: Basic CommandsVERIFY RESULTS FOR UN
Page 203 and 204: Basic CommandsExamplenaviseccli -h
Page 205 and 206: Basic Commandsgetunusedluns (not su
Page 207 and 208: Basic Commandsioportconfig -list (C
Page 209 and 210: Basic CommandsOutputInformation abo
Page 211 and 212: Basic Commandsluncache -clearDescri
Page 213 and 214: Basic Commandsluncache -listDescrip
Page 215 and 216: Basic Commands-wwnDisplays the Worl
Page 217 and 218: Basic Commandsmanagefiles -deleteDe
Page 219 and 220: Basic Commandsmanagefiles -listDesc
Page 221 and 222: Basic CommandsExamplenaviseccli -h
Page 223 and 224: Basic CommandsPrerequisitesOptionsO
Page 225 and 226: Basic CommandsWhen the installation
Page 227 and 228: Basic CommandsNote: If the storage
Page 229 and 230: Basic Commandsndu -runrulesExecutes
Page 231 and 232: Basic Commandsndu -commitDescriptio
Page 233 and 234: Basic Commandsndu -revert (AX4-5 se
Page 235 and 236: Basic Commandsnetworkadmin -getList
Page 237 and 238: Basic CommandsNote: If you have the
Page 239 and 240: Basic Commandsnetworkadmin -mibConf
Page 241: Basic Commandsnetworkadmin -setUpda
Page 245 and 246: Basic CommandsrebootSPDescriptionRe
Page 247 and 248: Basic Commandsremoteconfig -getconf
Page 249 and 250: Basic Commands-write filenameWrites
Page 251 and 252: Basic Commandsremoteconfig -setconf
Page 253 and 254: Basic CommandsOutputExampleSee page
Page 255 and 256: Basic Commandsresetandhold (CX3 ser
Page 257 and 258: Basic Commands-email-smtpmailserver
Page 259 and 260: Basic CommandsExample naviseccli -h
Page 261 and 262: Basic CommandsA lower value causes
Page 263 and 264: Basic Commands-rcb read-cache-spb (
Page 265 and 266: Basic Commandssetsniffer (CX series
Page 267 and 268: Basic CommandssetspstimeDescription
Page 269 and 270: Basic CommandssetsptimeDescriptionS
Page 271 and 272: Basic CommandsExample naviseccli -h
Page 273 and 274: Basic Commandsshutdownsp (AX4-5 ser
Page 275 and 276: Basic Commandsspcollect -info (auto
Page 277 and 278: Basic Commandsspcollect (manual ver
Page 279 and 280: Basic CommandsspportspeedDescriptio
Page 281 and 282: Basic CommandsiSCSI systems, port s
Page 283 and 284: Basic Commandssystemtype (AX4-5 ser
Page 285 and 286: Basic CommandstrespassDescriptionTr
Page 287 and 288: Basic CommandsunitserialnumberDescr
Page 289 and 290: Invisible Body Tag4Access Logix (St
Page 291 and 292: Access Logix (Storage Group) Comman
Page 293 and 294:
Access Logix (Storage Group) Comman
Page 295 and 296:
Page 297 and 298:
Page 299 and 300:
Page 301 and 302:
Page 303 and 304:
Page 305 and 306:
Page 307 and 308:
Page 309 and 310:
Page 311 and 312:
Page 313 and 314:
Page 315 and 316:
Page 317 and 318:
Page 319 and 320:
Page 321 and 322:
Page 323 and 324:
Page 325 and 326:
Invisible Body Tag5LUN Expansion(Me
Page 327 and 328:
LUN Expansion (MetaLUN) CommandsFig
Page 329 and 330:
LUN Expansion (MetaLUN) Commandsmet
Page 331 and 332:
LUN Expansion (MetaLUN) CommandsCon
Page 333 and 334:
LUN Expansion (MetaLUN) Commands-lu
Page 335 and 336:
LUN Expansion (MetaLUN) Commands-ex
Page 337 and 338:
LUN Expansion (MetaLUN) CommandsYou
Page 339 and 340:
Page 341 and 342:
Page 343 and 344:
LUN Expansion (MetaLUN) Commands-co
Page 345 and 346:
LUN Expansion (MetaLUN) CommandsTab
Page 347 and 348:
LUN Expansion (MetaLUN) CommandsWri
Page 349 and 350:
LUN Expansion (MetaLUN) Commands-de
Page 351 and 352:
LUN Expansion (MetaLUN) Commands3.
Page 353 and 354:
Invisible Body Tag6Reserved LUN Poo
Page 355 and 356:
Reserved LUN Pool CommandsEstimatin
Page 357 and 358:
Reserved LUN Pool Commandsreserved
Page 359 and 360:
Reserved LUN Pool Commandsreserved
Page 361 and 362:
Reserved LUN Pool Commandsnavicli o
Page 363 and 364:
Invisible Body Tag7iSCSI (Internet
Page 365 and 366:
iSCSI (Internet SCSI) CommandsAbout
Page 367 and 368:
iSCSI (Internet SCSI) CommandsWindo
Page 369 and 370:
iSCSI (Internet SCSI) CommandsThe f
Page 371 and 372:
iSCSI (Internet SCSI) CommandsComma
Page 373 and 374:
iSCSI (Internet SCSI) Commandseach
Page 375 and 376:
iSCSI (Internet SCSI) CommandsExamp
Page 377 and 378:
Page 379 and 380:
iSCSI (Internet SCSI) Commands-subn
Page 381 and 382:
iSCSI (Internet SCSI) Commandsconne
Page 383 and 384:
Page 385 and 386:
Page 387 and 388:
Page 389 and 390:
Page 391 and 392:
Page 393 and 394:
Page 395 and 396:
iSCSI (Internet SCSI) Commands-user
Page 397 and 398:
Page 399 and 400:
Page 401 and 402:
iSCSI (Internet SCSI) Commands-oSta
Page 403 and 404:
Page 405 and 406:
iSCSI (Internet SCSI) Commandsnavis
Page 407 and 408:
iSCSI (Internet SCSI) Commandsnavis
Page 409 and 410:
iSCSI (Internet SCSI) Commandsisns
Page 411 and 412:
Invisible Body Tag8LUN MigrationCom
Page 413 and 414:
LUN Migration CommandsOptionsThe co
Page 415 and 416:
LUN Migration Commandsmigrate -canc
Page 417 and 418:
LUN Migration Commandsmigrate -list
Page 419 and 420:
Invisible Body Tag9Domain and Secur
Page 421 and 422:
Domain and Security CommandsNote: T
Page 423 and 424:
Domain and Security Commandsdomain
Page 425 and 426:
Domain and Security Commandsdomain
Page 427 and 428:
Domain and Security CommandsExample
Page 429 and 430:
Domain and Security CommandsOptions
Page 431 and 432:
Domain and Security Commands0trueNT
Page 433 and 434:
Domain and Security Commands-keyval
Page 435 and 436:
Domain and Security Commandssecurit
Page 437 and 438:
Page 439 and 440:
Page 441 and 442:
Page 443 and 444:
Invisible Body TagACLI Error CodesT
Page 445 and 446:
CLI Error CodesError value(decimal)
Page 447 and 448:
Page 449 and 450:
Page 451 and 452:
Page 453 and 454:
Page 455 and 456:
Page 457 and 458:
Page 459 and 460:
Page 461 and 462:
Page 463 and 464:
Page 465 and 466:
Page 467 and 468:
CLI Error CodesClassic CLI error co
Page 469 and 470:
CLI Error CodesError valueDescripti
Page 471 and 472:
Page 473 and 474:
Page 475 and 476:
Page 477 and 478:
Page 479 and 480:
Page 481 and 482:
Page 483 and 484:
CLI Error CodesFeature command erro
Page 485 and 486:
CLI Error CodesConnection and iSNS
Page 487 and 488:
Invisible Body TagBUnsupportedComma
Page 489 and 490:
IndexAAccess Logix optiondefined 16
Page 491 and 492:
IndexFLARE software revision (getag
Page 493 and 494:
IndexPresent state, SP 164private L
Page 495 and 496:
Indexsetsniffer 265setspstime 267se
show all

Navisphere Command Line Interface (CLI) Reference - VMware Communities

Create successful ePaper yourself

Delete template?

Save as template?