ChromeGate 3.3.2 Software Manual - KNAUER Advanced Scientific ...

More documents

Recommendations

Info

Creating an Instrument Control Method 163 by clicking the Apply button. The On / Off button can be used for enabling / disabling the heating control. The labeling of the button changes with the actual status. Tray Temperature (°C) If the cooling option is installed and configured the tray temperature can be set. The entered value will be transferred to the sampler by clicking the Apply button. The On / Off button can be used for enabling / disabling the cooling control. The labeling of the button changes with the actual status. Start Needle Wash Press this button to force the autosampler to perform the needle wash. Advance Tray Clicking briefly on this button will move the tray to the next position. Instrument Status – Autosampler 3950 Fig. 241 Autosampler 3950 status tab Monitor AS Status The status Ready will be displayed when the autosampler is waiting to perform an injection. If an injection program is running, the actual program step will be indicated. After a completed injection, the status is described as Analysis timer running during the chromatographic run. Current Vial The actual position of the injection needle is shown. Tray Temperature (°C) If the tray cooling option has been installed and configured the actual tray temperature will be shown. Direct Control The direct control features are not accessible during an injection. Tray Temperature (°C) If the cooling option is installed and configured the tray temperature can be set. The entered value will be transferred to the sampler by clicking the Apply button. The Off button can be used for disabling the cooling control. To switch it on again set the required temperature and press the Apply button.
164 Creating an Instrument Control Method Reset Transport Vials (only with 84+3 vials tray) If the tray type 84+3 vials is configured, the button Reset Transport Vials allows for reset the transport liquid level of all transport vials (vials 85, 86, 87) to the default value of 8000 µl. If you click on that button, the software will ask if you wants to reset the filling level of all transport vials to 8000 µl. Click to do so or to leave the window without a level reset. Please be sure, that you also fill the transport vial(s), because the autosampler adjusts the needle immersion depth dependent on the vials filling level. If the vials will not fill, the autosampler can aspirate air instead transport liquid from the transport vial. The software cannot read-out or set the filling level. The transport vial filling level will automatically be reset, if the autosampler will be switched on. Start Needle Wash Press this button to force the autosampler to perform the needle wash. Move Tray Clicking briefly on this button will change the tray position: FRONT �� HOME. [>>…] The Stacked Injection table can be changed during a run. To have access, the option Direct Control during a run in Method – Runtime settings must be enabled. Pressing [>>…]-button during a run will open the known Stacked Injection setup with the default values. For the re-programming of the Stacked injection table, please refer the instrument setup chapter of the autosampler 3950. If you click on the Apply-button, the new stacked injection table will be executed immediately; the program will not check when the last injection was made. If the Direct Control during a run-option Save changes in time table is enabled, all program lines for stacked injections, which have not been executed yet during the current run, will be replaced by the stacked injections from the direct control, whereas lines for stacked injections, which have already been executing during the current run, remain untouched. If the Direct control during a run-option Save changes in time table is not active, the new table will be executed, but not stored in the instrument setup. However, in this case the method does not include the correct injection program.
Page 1 and 2:
Software ChromGate ® Chromatograph
Page 3 and 4:
4 CONTENTS Configuration - Autosamp
Page 5 and 6:
6 CONTENTS Peak Table .............
Page 7 and 8:
8 Installation Guide ChromGate® 3.
Page 9 and 10:
10 Installation Guide ChromGate® 3
Page 11 and 12:
12 Installation Guide ChromGate® 3
Page 13 and 14:
14 Short guide ChromGate®, KNAUER
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
32 Setup and Control of Knauer HPLC
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
84 Creating an Instrument Control M
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
100 Creating an Instrument Control
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112: 112 Creating an Instrument Control
Page 161: 162 Creating an Instrument Control
Page 169 and 170: 170 Knauer Instrument Control Metho
Page 185 and 186: 186 ChromGate® System Suitability
Page 187 and 188: 188 ChromGate® System Suitability
Page 189 and 190: 190 ChromGate® PDA Option Fig. 283
Page 191 and 192: 192 ChromGate® PDA Option calculat
Page 193 and 194: 194 ChromGate® PDA Option (to the
Page 195 and 196: 196 ChromGate® PDA Option PDA View
Page 213 and 214:
214 ChromGate® PDA Option Fig. 313
Page 215 and 216:
216 ChromGate® PDA Option Note tha
Page 217 and 218:
Page 219 and 220:
Page 221 and 222:
222 PDA Analysis and Calculations c
Page 223 and 224:
224 PDA Analysis and Calculations s
Page 225 and 226:
226 PDA Analysis and Calculations u
Page 227 and 228:
228 PDA Analysis and Calculations 3
Page 229 and 230:
230 ChromGate® Preparative Option
Page 231 and 232:
Page 233 and 234:
Page 235 and 236:
Page 237 and 238:
Page 239 and 240:
Page 241 and 242:
Page 243 and 244:
Page 245 and 246:
Page 247 and 248:
Page 249 and 250:
Page 251 and 252:
Page 253 and 254:
Page 255 and 256:
Page 257 and 258:
258 SEC Option Universal Calibratio
Page 259 and 260:
260 SEC Option Fig. 369 Acquisition
Page 261 and 262:
262 SEC Option Amount Values In thi
Page 263 and 264:
264 SEC Option Fig. 373 SEC peak an
Page 265 and 266:
266 SEC Option Fig. 376 Fig. 377 Yo
Page 267 and 268:
268 SEC Option Fig. 379 Enable Anal
Page 269 and 270:
270 SEC Option Export settings Clic
Page 271 and 272:
272 SEC Option All samples analyzed
Page 273 and 274:
274 SEC Option Horizontal Baseline
Page 275 and 276:
276 SEC Option Intrinsic Viscosity
Page 277 and 278:
278 SEC Option Fig. 383 information
Page 279 and 280:
280 SEC Option Fig. 386 Fig. 387 Se
Page 281 and 282:
282 SEC Option single variable sear
Page 283 and 284:
284 Typical Wiring Schemes Typical
Page 285 and 286:
286 Typical Wiring Schemes Fig. 390
Page 287 and 288:
288 Typical Wiring Schemes Fig. 392
Page 289 and 290:
290 Fig. 394 Pump K-1001 / Autosamp
Page 291 and 292:
292 Index Device ID Autosampler 68,
Page 293 and 294:
294 Index R Rack configuration 243
Page 295:
© ® Wissenschaftliche Gerätebau
show all

ChromeGate 3.3.2 Software Manual - KNAUER Advanced Scientific ...

Create successful ePaper yourself

Delete template?

Save as template?