ChromeGate 3.3.2 Software Manual - KNAUER Advanced Scientific ...

More documents

Recommendations

Info

Setup and Control of Knauer HPLC Systems 33 Number of boxes Select the number of boxes used in the system. ChromGate ® supports up to 4 Knauer Interface Boxes. Configure box # Select the box you wish to configure. Each box has to be configured separately. Serial Port Manager 5000/5050 / Interface Box IF2 Select the number for the communication port on your PC to which the Manager 5000/5050 or the Interface Box IF2 is connected. Interface Box Model 96 The Knauer Interface Box supports the binary Knauer Net. The networks 1, 2,... correspond to the number of the utilized communication port (COM1, COM2,...). Select the number for the communication port on your PC to which the Interface Box is connected. You can use the Interface Box or the Manager 5000/5050 to acquire signals from different instruments at the same time. It is necessary to connect the interfaces to separate communication ports on a PC. See the Typical Cabling / Wiring chapter, Fig. 389 on page 285. Serial Number Type in the serial number of the Interface Box / Manager 5000/5050 you are using. The serial number is used for the device identification and addressing during serial communications. This serial number should match the serial number of the Interface Box. For Knauer HPLC-Boxes with an S/N higher than 65000, only the last 4 digits of the S/N must be entered (e.g. 5567 instead of 65567). Box type The only choice is Model 96. No others are selectable. Channel Four data acquisition channels are normally available. However, only channel one will be available if you have checked the 100 Hz sampling rate option in model 96 or 50 Hz in case of Manager 5000/5050 / IF2 (see Sampling rate on page 91). Fig. 33 Dialog box for configuring the Model 96 Interface Box with activated 100 Hz option Range Select the Signal Range for the channel chosen from the channel dropdown list. The choices are +/-10 V, +/-1 V, +/-0.1 V, +/-0.01 V for the Interface Box and +/-2.56 V, +/-1.28 V, +/-0.64 V, +/-0.16 V for the Manager 5000/5050 / IF2. The Signal Range specifies the maximum
34 Setup and Control of Knauer HPLC Systems analog input voltage to be digitized by an A/D converter. Use the Signal Range to optimize the signal-to-noise ratio of the measured signal. Manufacturer and Model This area is for information only. It contains manufacturing information about the box which may be required in service situations. Kontron Interface Configuration If you are using a Kontron interface card click on the corresponding icon, and then click Properties. A dialog box will appear where you can configure the interface (see Fig. 34). If you configure the interface newly the message like Fig. 31 on page 32 will remind you to enter the serial number of the interface device. Fig. 34 Dialog box for configuring the Kontron interface card PCI AD Number of PC cards Select the number of PC cards used in the system. ChromGate ® supports up to 4 interfaces. Configure card # Select the card you wish to configure. Each card has to be configured separately. Card type: Select either ISA AD or PCI AD. In case of selected PCI AD the setup window is changed to the following appearance. Fig. 35 Dialog box for configuring the Kontron interface card ISA AD
Page 1 and 2: Software ChromGate ® Chromatograph
Page 3 and 4: 4 CONTENTS Configuration - Autosamp
Page 5 and 6: 6 CONTENTS Peak Table .............
Page 7 and 8: 8 Installation Guide ChromGate® 3.
Page 9 and 10: 10 Installation Guide ChromGate® 3
Page 11 and 12: 12 Installation Guide ChromGate® 3
Page 13 and 14: 14 Short guide ChromGate®, KNAUER
Page 31: 32 Setup and Control of Knauer HPLC
Page 35 and 36: 36 Setup and Control of Knauer HPLC
Page 83 and 84:
84 Creating an Instrument Control M
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
100 Creating an Instrument Control
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
170 Knauer Instrument Control Metho
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
Page 185 and 186:
186 ChromGate® System Suitability
Page 187 and 188:
188 ChromGate® System Suitability
Page 189 and 190:
190 ChromGate® PDA Option Fig. 283
Page 191 and 192:
192 ChromGate® PDA Option calculat
Page 193 and 194:
194 ChromGate® PDA Option (to the
Page 195 and 196:
196 ChromGate® PDA Option PDA View
Page 197 and 198:
Page 199 and 200:
Page 201 and 202:
Page 203 and 204:
Page 205 and 206:
Page 207 and 208:
Page 209 and 210:
Page 211 and 212:
Page 213 and 214:
Page 215 and 216:
216 ChromGate® PDA Option Note tha
Page 217 and 218:
Page 219 and 220:
Page 221 and 222:
222 PDA Analysis and Calculations c
Page 223 and 224:
224 PDA Analysis and Calculations s
Page 225 and 226:
226 PDA Analysis and Calculations u
Page 227 and 228:
228 PDA Analysis and Calculations 3
Page 229 and 230:
230 ChromGate® Preparative Option
Page 231 and 232:
Page 233 and 234:
Page 235 and 236:
Page 237 and 238:
Page 239 and 240:
Page 241 and 242:
Page 243 and 244:
Page 245 and 246:
Page 247 and 248:
Page 249 and 250:
Page 251 and 252:
Page 253 and 254:
Page 255 and 256:
Page 257 and 258:
258 SEC Option Universal Calibratio
Page 259 and 260:
260 SEC Option Fig. 369 Acquisition
Page 261 and 262:
262 SEC Option Amount Values In thi
Page 263 and 264:
264 SEC Option Fig. 373 SEC peak an
Page 265 and 266:
266 SEC Option Fig. 376 Fig. 377 Yo
Page 267 and 268:
268 SEC Option Fig. 379 Enable Anal
Page 269 and 270:
270 SEC Option Export settings Clic
Page 271 and 272:
272 SEC Option All samples analyzed
Page 273 and 274:
274 SEC Option Horizontal Baseline
Page 275 and 276:
276 SEC Option Intrinsic Viscosity
Page 277 and 278:
278 SEC Option Fig. 383 information
Page 279 and 280:
280 SEC Option Fig. 386 Fig. 387 Se
Page 281 and 282:
282 SEC Option single variable sear
Page 283 and 284:
284 Typical Wiring Schemes Typical
Page 285 and 286:
286 Typical Wiring Schemes Fig. 390
Page 287 and 288:
288 Typical Wiring Schemes Fig. 392
Page 289 and 290:
290 Fig. 394 Pump K-1001 / Autosamp
Page 291 and 292:
292 Index Device ID Autosampler 68,
Page 293 and 294:
294 Index R Rack configuration 243
Page 295:
© ® Wissenschaftliche Gerätebau
show all

ChromeGate 3.3.2 Software Manual - KNAUER Advanced Scientific ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?