Bravo & Brava • 1995 To 2000

More documents

Recommendations

Info

12*18 Body electrical systems 17.16d Removing the washer tube from the nozzle/adapter 16 Extract the circlip and washer, then pull the nozzle/adapter from the wiper spindle housing. If necessary, remove the tube, (see illustrations). Refitting 17 Refitting is a reversal of removal, but on completion adjust the washer jet using a small screwdriver through the hole in the nozzle/adapter. The jet should be directed towards the upper area of the tailgate wiper wiped area. Headlight washer nozzle Removal 18 The headlight washer nozzles are located in the front bumper. First remove the front bumper as described in Chapter 11. 19 Disconnect the tube and adapter from the bottom of the headlight nozzle. 18.3a Pull up the weatherstrips ... 20 Unscrew the nut and withdraw the nozzle from the front bumper. Refitting 21 Refitting is a reversal of removal. 18 Windscreen wiper motor - removal and refitting Removal 1 Make sure that the windscreen wiper motor is in its 'parked' position by briefly switching it on and off. Make sure that the ignition is switched off. 2 Refer to Section 19 and remove both wiper arms. 3 With the bonnet open, pull up the 18.3b . then undo the screws . weatherstrips and undo the screws, then unclip and remove the cowl panel from in front of the windscreen. Note that the two rear screws are accessed by prising out the two covers (see illustrations). 4 Remove the protective cover from the windscreen wiper motor. 5 Disconnect the wiring plug from the motor (see illustration). 6 Unscrew and remove the three mounting bolts, and withdraw the wiper motor assembly from the bulkhead (see illustrations). 7 Unscrew the crank retaining nut, and the three mounting bolts, then separate the wiper motor from the linkage. Refitting 8 Refitting is a reversal of removal, but ensure that the motor drive is in the 'parked' position before reconnecting the crank arm. 18.3c ... and remove the cowl panel 18.5 Disconnect the wiring from the wiper 18.6a Wiper mounting bolt located by the motor motor
18.6b Wiper mounting bolt located on the linkage frame 19 Wiper arm - ^ removal and refitting || Removal 1 Operate the wiper motor, then switch it off so that the wiper arm returns to its 'parked' position. 2 Stick masking tape on the glass, to use as an alignment aid for the rest position of the wiper blade. Note, however, that there is a mark on the tailgate window glass for locating the blade in its 'rest' position (see illustrations). 3 Prise out the wiper arm spindle nut cover, then unscrew and remove the spindle nut. Recover the washer (see illustrations). 19.2a The 'rest' position mark on the tailgate window glass 19.3b ... remove the nut and washer ... 18.6c Removing the wiper motor assembly from the bulkhead 4 Lift the blade off the glass, and ease the wiper arm off its spindle, using a rocking action (see illustrations). If both windscreen wiper arms are being removed, note both locations, as different arms are fitted to each side. Refitting 5 Refitting is a reversal of removal, but ensure that the wiper arm and spindle splines are clean and dry and align the blade with the tape before tightening the spindle nut securely. 20 Anti-theft alarm/engine immobiliser system - general information Note: This information is applicable only to the 19.2b Stick masking tape on the windscreen to indicate the 'rest' position of the wiper blade 19.4a ... and remove the tailgate wiper arm from the spindle Body electrical systems 12*19 ft 18.6d Wiper motor and linkage removed from the bulkhead anti-theft alarm system fitted by FIAT as standard equipment. 1 All models are fitted with a FIAT CODE engine immobiliser system as standard equipment. The immobiliser is automatically activated when the ignition key is turned to PARK or STOP, and will also be activated when the key is removed completely from the switch. The ignition key has an integral device which transmits a coded signal to the FIAT CODE unit on the ignition switch, and the unit will only allow the engine to be started if it recognises the signal. 2 Each new car is provided with one master key (burgundy) and two duplicate keys (blue) for normal use. The duplicate keys incorporate a battery on models with remote central locking and an alarm system. The master key should be kept in a safe place, as 19.3a Prise out the wiper arm spindle nut cover... 19.4b Removing the windscreen wiper arm from its spindle
Page 1 and 2:
BRAVO & BRAVA • 1995 to 2000 (N t
Page 3 and 4:
Contents LIVING WITH YOUR FIAT BRAV
Page 5 and 6:
o.4 Introduction The 3-door FIAT Br
Page 7 and 8: o.6 Roadside repairs The following
Page 9 and 10: o.8 Roadside repairs Wheel changing
Page 11 and 12: o«io Weekly checks Introduction Th
Page 13 and 14: o-i2 Weekly checks Engine oil level
Page 15 and 16: o.i4 Weekly checks Tyre condition a
Page 17 and 18: o.i6 Weekly checks Washer fluid lev
Page 19 and 20: Chapter 1 Routine maintenance & ser
Page 21 and 22: Torque wrench settings (continued)
Page 23 and 24: 1 Washer reservoir 2 Inlet manifold
Page 25 and 26: 1 Introduction General information
Page 27 and 28: A - -A 6.3 Topping-up the battery e
Page 29 and 30: 7.21 Set the belt tension, then tig
Page 31 and 32: Try to move the pipes and silencers
Page 33 and 34: 18.6 Pull the HT leads off the spar
Page 35 and 36: 5 Before removing the filter, note
Page 37 and 38: 2 To fully check the operation of t
Page 39 and 40: 31.3a Opening the radiator bleed sc
Page 41 and 42: Chapter 12 Body electrical systems
Page 43 and 44: 1 General information and precautio
Page 45 and 46: to release the clip, then withdraw
Page 47 and 48: Body electrical systems 12»7 4.35a
Page 49 and 50: 14 Extract the festoon-type bulb fr
Page 51 and 52: 6.18a Unscrew the mounting bolts ..
Page 53 and 54: 10.2 Prise the speaker grille from
Page 55 and 56: Body electrical systems 12»15 14.4
Page 57: 15.3c ... and remove the inner meta
Page 61 and 62: 22.3b Disconnect the yellow wiring
Page 63 and 64: Key to symbols — t ; j^g. Item nu
Page 65 and 66: Wire colours W White R Red Y Yellow
Page 67 and 68: Wire colours W White O Orange R Red
Page 69 and 70: Wire colours W White O Orange R Red
Page 71 and 72: Wire colours W R Y Br P Bl Gr G B V
Page 73 and 74: Wire colours Key to items w R Y Br
Page 75 and 76: 11 »2 Bodywork and fittings which
Page 77 and 78: 11 »4 Bodywork and fittings 6 Fron
Page 79 and 80: '\'\»6 Bodywork and fittings the c
Page 81 and 82: 11 »8 Bodywork and fittings 10.11
Page 83 and 84: 11*10 Bodywork and fittings 7 If wo
Page 85 and 86: 11*12 Bodywork and fittings 16.10 R
Page 87 and 88: 11*14 Bodywork and fittings 18.3a U
Page 89 and 90: 11*16 Bodywork and fittings 18.23a
Page 91 and 92: 11*18 Bodywork and fittings 20.15b
Page 95 and 96: 11 »22 Bodywork and fittings 16 Wi
Page 99 and 100: 10*2 Suspension and steering system
Page 105 and 106: 1f>8 Suspension and steering system
Page 107 and 108: 10*10 Suspension and steering syste
Page 109 and 110:
10«12 Suspension and steering syst
Page 111 and 112:
10*14 Suspension and steering syste
Page 113 and 114:
9*2 Braking system Anti-lock brakin
Page 115 and 116:
9*4 Braking system 4.2 Disconnectin
Page 117 and 118:
9*6 Braking system 5 Unhook the sel
Page 119 and 120:
9*8 Braking system 5.27 Removing th
Page 121 and 122:
9*10 Braking system 8.4 Disconnecti
Page 123 and 124:
9»12 Braking system K-0 10.13 Cros
Page 125 and 126:
9»14 Braking system 25 Working ins
Page 127 and 128:
9*16 Braking system 2 Unbolt the ex
Page 129 and 130:
8*2 Driveshafts 1 General informati
Page 131 and 132:
8*4 Driveshafts 3.23a Extract the c
Page 133 and 134:
8*6 Driveshafts 4.7 Unbolt the inte
Page 135 and 136:
Chapter 7 Part B: Automatic transmi
Page 137 and 138:
2.19a Two of the six bolts securing
Page 139 and 140:
S§^)/ H31468 6.11 Selector lever p
Page 141 and 142:
Chapter 7 Part A: Manual transmissi
Page 143 and 144:
2 Gearchange lever and linkage remo
Page 145 and 146:
hoist to the left-hand end of the i
Page 147 and 148:
) Apply a smear of high-melting-poi
Page 149 and 150:
6*2 Clutch 1 General information Ve
Page 151 and 152:
6«4 Clutch 6.4 Clutch slave cylind
Page 153 and 154:
Chapter 5 Part B: Ignition system C
Page 155 and 156:
2.8 Diagnostic connector plug locat
Page 157 and 158:
4.4 Pull the HT leads off the spark
Page 159 and 160:
6.1 Crankshaft sensor on 1.6 litre
Page 161 and 162:
Chapter 5 Part A: Starting and char
Page 163 and 164:
Starting and charging systems 5A»3
Page 165 and 166:
5.13a Unscrew the bolts securing th
Page 167 and 168:
6 Unscrew and remove the starter mo
Page 169 and 170:
402 Exhaust and emission control sy
Page 171 and 172:
404 Exhaust and emission control sy
Page 173 and 174:
Chapter 4 Part B: Fuel system - mul
Page 175 and 176:
2.5 Disconnecting the breather hose
Page 177 and 178:
4.3c Disconnecting the throttle pot
Page 179 and 180:
Refitting 20 Refit the injectors an
Page 181 and 182:
Unplug the wiring connectors and un
Page 183 and 184:
5.10a Once the base of the unit has
Page 185 and 186:
8.8b ... and remove this wiring har
Page 187 and 188:
Chapter 4 Part A: Fuel system - sin
Page 189 and 190:
6 Slacken and withdraw the securing
Page 191 and 192:
5.1 Disconnect the breather hose fr
Page 193 and 194:
Refitting 17 Refitting is a reversa
Page 195 and 196:
Fuel system - single-point injectio
Page 197 and 198:
Disconnect the inlet manifold coola
Page 199 and 200:
Chapter 3 Cooling, heating and vent
Page 201 and 202:
eveal a faulty hose, it must be ren
Page 203 and 204:
Refitting 14 Ensure that the cylind
Page 205 and 206:
36 Unbolt and remove the timing bel
Page 207 and 208:
Cooling, heating and ventilation sy
Page 209 and 210:
Chapter 2 Part E: Engine removal an
Page 211 and 212:
Crankshaft Main bearing journal dia
Page 213 and 214:
2.20a Removing the cover from the b
Page 215 and 216:
2.33 Removing the left-hand wheelar
Page 217 and 218:
Automatic transmission models 64 Re
Page 219 and 220:
4.20 Look for cracking between the
Page 221 and 222:
4.45a Locate the inner . 4.45b ...
Page 223 and 224:
5.24a Using a small screwdriver ...
Page 225 and 226:
5.47 Tightening the big-end bearing
Page 227 and 228:
8.14 Three bore measurement points
Page 229 and 230:
11.19 Lubricate the crankcase main
Page 231 and 232:
2D»2 1.8 litre engine in-car repai
Page 233 and 234:
Location of TDC on No 1 cylinder 1
Page 235 and 236:
4.13a Removing No 3 exhaust camshaf
Page 237 and 238:
camshaft oil seals for signs of lea
Page 239 and 240:
14 If necessary, remove and clean t
Page 241 and 242:
37 Again working in sequence, tight
Page 243 and 244:
^^^^^ 13.8 Using an impact screwdri
Page 245 and 246:
202 1.6 litre engine in-car repair
Page 247 and 248:
Page 249 and 250:
Page 251 and 252:
Page 253 and 254:
2O10 1.6 litre engine in-car repair
Page 255 and 256:
2012 1.6 litre enginein-car repair
Page 257 and 258:
Page 259 and 260:
Page 261 and 262:
Page 263 and 264:
2O20 1.6 litre engine in-car repair
Page 265 and 266:
Chapter 2 Part B: 1.4 litre engine
Page 267 and 268:
6 Once pressure is felt, continue t
Page 269 and 270:
4.17 FIAT special tool used to lock
Page 271 and 272:
Section 4. It is essential that an
Page 273 and 274:
paragraph 17), then remove the heat
Page 275 and 276:
to the downpipe. The safest option
Page 277 and 278:
13.8 Using an impact screwdriver to
Page 279 and 280:
2A«2 1.2 litre engine in-car repai
Page 281 and 282:
2A«4 1.2 litre engine in-car repai
Page 283 and 284:
2A»6 1.2 litre engine in-car repai
Page 285 and 286:
2A»8 1.2 litre engine in-car repai
Page 287 and 288:
2A»10 1.2 litre engine in-car repa
Page 289 and 290:
Page 291 and 292:
Page 293 and 294:
REF-2 Conversion factors Length (di
Page 295 and 296:
REF.4 Vehicle identification number
Page 297 and 298:
REF.6 Disconnecting the battery Sev
Page 299 and 300:
REF.8 Tools and working facilities
Page 301 and 302:
REF.10 MOT test checks This is a gu
Page 303 and 304:
REF«12 MOT test checks Exhaust sys
Page 305 and 306:
REF.14 Fault finding Engine • Eng
Page 307 and 308:
REF.16 Fault finding Engine (contin
Page 309 and 310:
REF.18 Fault finding Clutch Note: T
Page 311 and 312:
REF.20 Fault finding Braking system
Page 313 and 314:
REF.22 Fault finding Electrical sys
Page 315 and 316:
REF.24 Glossary of technical terms
Page 317 and 318:
Page 319 and 320:
Page 321 and 322:
REF
Page 323 and 324:
REF
show all

Bravo & Brava • 1995 To 2000

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?