Safety Integrated - Industry - Siemens

More documents

Recommendations

Info

Ex. No. 10 Configuration and diagnosis software LS4Soft The following example illustrates how to load the example file as_fe_i_010_v10_code_plscanner.ls to the LS4 using LS4Soft. The sample file is available as separate download (like as the respective STEP 7 project). No. Instruction Note 1 Install the LS4Soft software on your PG/PC. – 2 Switch on the LS4. – 3 Start LS4Soft. – 4 Connect the COM interface of your PG/PC with the LS4 via the PC adapter. The configuration data currently located on the LS4 are now loaded. 5 Register as "authorized customer" and enter the required password LS4SIG. 6 Wait until the LS4 has determined the status information. – 7 Click "Close". – 302 Functional Example No. AS-FE-I-010-V11-EN A query that no individual password has been specified appears.
No. Instruction Note 8 Click "Cancel". No new configuration shall be generated, but the example file as_fe_i_010_v10_code_plscanner. ls be used. 9 Verify whether the "Display of measurement values" is active. The currently active zone pairs and contours appear. 10 Activate the "LS4 configuration" tab via mouse click and select LS4 configuration -> Load configuration data from file and transfer to LS4 system from the menu – 11 Now search the example file as_fe_i_010_v10_code_plscanner.ls and follow the further instructions Note Ensure the COM interface is set correctly. The COM interface settings are available in the menu Settings -> PC configuration -> Interface – Functional Example No. AS-FE-I-010-V11-EN 303 Ex. No. 10
Page 1 and 2:
safety INTEGRATED Safety applicatio
Page 3 and 4:
Safety Integrated Functional Exampl
Page 5 and 6:
42 2.8 E-Stop with monitored start
Page 7 and 8:
Structure and wiring An overview of
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Required components Hardwarekompone
Page 29 and 30:
Required components Hardware compon
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Emergency Stop with monitored start
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Protective door monitoring with aut
Page 65 and 66:
2 safety circuits in a cascade acco
Page 67 and 68:
Components required Hardware compon
Page 69 and 70:
Important hardware component settin
Page 71 and 72:
Note Diagram Overload, thermal moto
Page 73 and 74:
Required Components This chapter co
Page 75 and 76:
Example Code This chapter describes
Page 77 and 78:
Description Parameters The contacto
Page 79 and 80:
Configuration validation Starting t
Page 81 and 82:
Required Components This chapter co
Page 83 and 84:
Page 85 and 86:
Description Parameters For the doub
Page 87 and 88:
Commissioning the AS Interface Safe
Page 89 and 90:
Protective door with door interlock
Page 91 and 92:
Assembly and Wiring Overview of Har
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
SIMOCODE pro direct starters with s
Page 131 and 132:
Required Components Hardware compon
Page 133 and 134:
Wiring of Hardware Components
Page 135 and 136:
Note Screenshot SIMOCODE is inserte
Page 137 and 138:
Parameter settings Note Screenshot
Page 139 and 140:
Downloading the SIMOCODE pro projec
Page 141 and 142:
The displayed link is parameterized
Page 143 and 144:
SIMOCODE pro reversing starters wit
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
SIMOCODE pro star-delta starters wi
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Fail-safe Controllers SIMATIC Safet
Page 173 and 174:
Page 175 and 176:
L1 N PE Note A connection between t
Page 177 and 178:
Settings of the CPU 315F-2DP The se
Page 179 and 180:
The sample code with the given conf
Page 181 and 182:
Safety Door with Spring-Loaded Enga
Page 183 and 184:
Page 185 and 186:
L1 N PE PS 307 / CPU 315F L+ M IM 1
Page 187 and 188:
Page 189 and 190:
Basic Performance Data Load and mai
Page 191 and 192:
Note If the above section is not ob
Page 193 and 194:
FB "COORDINATION" (FB1, DB1) After
Page 195 and 196:
Safety Door with Magnetic Engagemen
Page 197 and 198:
Setup and Wiring In order to set up
Page 199 and 200:
Function test After wiring the hard
Page 201 and 202:
Page 203 and 204:
Basic Performance Data Load and mai
Page 205 and 206:
FC "STANDARD" (FC 3) The FC "STANDA
Page 207 and 208:
The safety door locks ("COIL"="1"),
Page 209 and 210:
Safety Door without Guard Locking i
Page 211 and 212:
Page 213 and 214:
Page 215 and 216:
Page 217 and 218:
Sample Code Preliminary Remarks Enc
Page 219 and 220:
The acknowledgement for the enable
Page 221 and 222:
Light Curtain in Category 4 with Mu
Page 223 and 224:
Flow chart The flow chart below sho
Page 225 and 226:
ACK PS 307 START CPU 315F Wiring of
Page 227 and 228:
Page 229 and 230:
Set mode: "Test Mode" During Proces
Page 231 and 232:
Sample Code Preliminary Remarks Enc
Page 233 and 234:
FB "L_CURTAIN" (FB 1, DB 1) FB 1 ha
Page 235 and 236:
Two-Hand Control Panel with Integra
Page 237 and 238:
Page 239 and 240:
L1 N PE PS 307 / CPU 315F L+ M IM 1
Page 241 and 242:
Page 243 and 244:
Settings of the failsafe F-DO The s
Page 245 and 246:
F-CALL (FC1) F-CALL (FC1) is the F
Page 247 and 248:
Integration of the Readback Signal
Page 249 and 250:
Page 251 and 252:
L1 N PE PS 307 / CPU 315F L+ M AUX1
Page 253 and 254: Important hardware component settin
Page 255 and 256: Settings of the failsafe F-DO The s
Page 257 and 258: Sample Code Preliminary Remarks Enc
Page 259 and 260: Warning! When using the F applicati
Page 261 and 262: Safety Shutdown in the Stop Categor
Page 263 and 264: G_FB_XX_152 Time sequence for Stop
Page 265 and 266: Setup and Wiring Regarding the use
Page 267 and 268: Parameters used Below, some charact
Page 269 and 270: L1 N PE PS 307 / CPU 315F A4 2 DO H
Page 271 and 272: Function test The inputs and output
Page 273 and 274: Set mode: "Test Mode" During Proces
Page 277 and 278: Network 2 FB "Safety_PRG" (FB1, DB1
Page 279 and 280: Single and Group Shutdown of Actuat
Page 281 and 282: Required components Hardware compon
Page 283 and 284: Note The DP interface of the CPU 31
Page 285 and 286: The terminal markings of the load c
Page 289 and 290: Settings of the failsafe F-DO The s
Page 291 and 292: COND2), which can be changed by the
Page 293 and 294: Please consider the following notes
Page 295 and 296: 7 Cyclic input data 0 OSSD Warning!
Page 297 and 298: Time sequence For a better understa
Page 299 and 300: Advantages/customer benefits ■ Fo
Page 301 and 302: IM 151 HF IM 151 HF PM-E PM-E 2DI H
Page 303: Connection of the LS4 Integrating t
Page 307 and 308: Function test After wiring the hard
Page 311 and 312: Settings of the fail-safe F-DO The
Page 315 and 316: FB "SET_ACT" (FB 3, DB 3) Network 1
Page 317 and 318: #SEN_FIELD 1 #SEN_FIELD 2 #SEN_FIEL
Page 319 and 320: Passivation and Reintegration of F-
Page 321 and 322: Setup and Wiring This chapter descr
Page 323 and 324: Overview of inputs and outputs Over
Page 327 and 328: "Channel 1.5": "Evaluation of the s
Page 329 and 330: Sample Code In this chapter you lea
Page 331 and 332: Scenario: Manual reintegration Disc
Page 333 and 334: Scenario: F-communication error Dis
Page 335 and 336: Overview of buttons and indicator l
Page 337 and 338: Explanations for the STEP 7 program
Page 339 and 340: FB2 / Network 1 DB818.DBX 36.4 Over
Page 341 and 342: Description: FB3, DB4 (REINTEGRATIO
Page 343 and 344: FB3 / Netzwerk 3 Overview of the si
Page 345 and 346: Operation: Normal operation Operati
Page 347 and 348: Operation: Automatic reintegration
Page 349 and 350: Background Knowledge on the Functio
Page 351 and 352: F-I/O-module data block What is an
Page 353 and 354: The user has read and write access
Page 355 and 356:
Passivation (of entire module or ch
Page 357 and 358:
How is the "passivation of channels
Page 359 and 360:
Processes during passivation and re
Page 361 and 362:
Process: Channel / module error (ma
Page 363 and 364:
Process: Safety program Preconditio
Page 365 and 366:
Warning Automatic reintegration is
Page 367 and 368:
This communication is realized via
Page 369 and 370:
DP Slave (MASTERDRIVES) The descrip
Page 371 and 372:
Emergency stop Time Explanation t1
Page 373 and 374:
Page 375 and 376:
Notes on configuring MASTERDRIVES N
Page 377 and 378:
Inputs and outputs used for the DP
Page 379 and 380:
Overview hardware configuration of
Page 381 and 382:
Settings of the fail-safe F-DI The
Page 383 and 384:
Basic Performance Data DP Master: L
Page 385 and 386:
Program sequence General overview T
Page 387 and 388:
Symbol Function Explanation START P
Page 389 and 390:
Network 4: Reading in the readback
Page 391 and 392:
Variables of FB "STANDSTILL_AND_SAF
Page 393 and 394:
Network 10 In this network, the tim
Page 395 and 396:
Network 2 With OUT3=0 the drive is
Page 397 and 398:
Safety Drives System 1 SAFE STANDST
Page 399 and 400:
Behavior when Emergency Stop is iss
Page 401 and 402:
Page 403 and 404:
Behavior when the protective doors
Page 405 and 406:
Function description A structure in
Page 407 and 408:
Page 409 and 410:
Page 411 and 412:
■ This circuit principle is suita
Page 413 and 414:
Certificate The examples shown in t
Page 415 and 416:
Page 417 and 418:
Page 419 and 420:
Page 421 and 422:
Page 423 and 424:
Page 425 and 426:
Page 427 and 428:
■ This circuit principle is suita
Page 429 and 430:
Certificate The examples shown in t
Page 431 and 432:
"Safe standstill" with SINAMICS usi
Page 433 and 434:
"Safety Integrated" settings The de
Page 435 and 436:
Behavior, when the protective doors
Page 437 and 438:
Behavior at Emergency Stop Emergenc
Page 439 and 440:
The safety requirements are fulfill
Page 441 and 442:
Hardware components for the F-CPU c
Page 443 and 444:
Overview of interfaces and communic
Page 445 and 446:
Overview of the network configurati
Page 447 and 448:
SINAMICS Runtime System Parametizat
Page 449 and 450:
SIMOTION Runtime System Starting up
Page 451 and 452:
SIMATIC Runtime System Function Blo
Page 453 and 454:
Overview of the function block "F_D
Page 455 and 456:
Überwachung auf sicher red. Geschw
Page 457 and 458:
Plausibility check: Motion command
Page 459 and 460:
Porting PROFIsafe to the applicatio
Page 461 and 462:
Input signal conditioning The incom
Page 463 and 464:
TÜV certificate (issued by the TUE
Page 465 and 466:
SINAMICS G120 - controlled via PROF
Page 467 and 468:
Required components An overview of
Page 469 and 470:
Connecting-up the hardware componen
Page 471 and 472:
Fault 395 (acceptance test / acknow
Page 473 and 474:
Overview of inputs and outputs Simu
Page 475 and 476:
Download S7 program To download the
Page 477 and 478:
nels takes approximately 2.4s. This
Page 479 and 480:
Please note that the two actual che
Page 481 and 482:
Key performance data Load memory an
Page 483 and 484:
The individual telegram components
Page 485 and 486:
DB1, axis_DB The axis_DB represents
Page 487 and 488:
SINAMICS G120 parameterization In o
Page 489 and 490:
SINAMICS G120 - controlled via PROF
Page 491 and 492:
Required components An overview of
Page 493 and 494:
Connecting-up the hardware componen
Page 495 and 496:
Fault 395 (acceptance test / acknow
Page 497 and 498:
Overview of inputs and outputs Simu
Page 499 and 500:
■ Then, in the Project Navigator
Page 501 and 502:
Safe Stop 1 (SS1) tab The parameter
Page 503 and 504:
Function test The function test can
Page 505 and 506:
Siemens telegram 352, PZD 6/6 The s
Page 507 and 508:
Principle structure of the FC100 Ne
Page 509 and 510:
Functional Example No. SD-FE-I-002-
Page 511 and 512:
Contact partners Contact partners f
show all

Safety Integrated - Industry - Siemens

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?