Cortex-A8 Technical Reference Manual - ARM Information Center

More documents

Recommendations

Info

AC Characteristics The hold parameter values are based on the Fast-Fast (FF) corner under the following conditions: • -40 C • VDD = nominal operating voltage + 10% • target frequency = fmax. The nominal operating voltage for the process is defined to be Vdd. Note The hold time requirements for the macrocell I/O are not specified in this document. The hold time is specific to process and implementation requirements and therefore, are controlled by the implementor. ARM DDI 0344K Copyright © 2006-2010 ARM Limited. All rights reserved. 17-3 ID060510 Non-Confidential
17.2 AXI interface Table 17-2 shows the setup and hold times for the AXI interface signals. Signal Clock AC Characteristics Table 17-2 Timing parameters of AXI interface Setup parameter Percent of clock period A64n128 a CLK - - - Hold parameter ACLKEN CLK Tisaclken 30% Tihaclken ARADDR[31:0] CLK Tovaraddr 30% Toharaddr ARBURST[1:0] CLK Tovarburst 30% Toharburst ARCACHE[3:0] CLK Tovarcache 30% Toharcache ARID[3:0] CLK Tovarid 30% Toharid ARLEN[3:0] CLK Tovarlen 30% Toharlen ARLOCK[1:0] CLK Tovarlock 30% Toharlock ARPROT[2:0] CLK Tovarprot 30% Toharprot ARSIZE[2:0] CLK Tovarsize 30% Toharsize ARVALID CLK Tovarvalid 30% Toharvalid ARREADY CLK Tisarready 30% Tiharready RDATA[127:0] CLK Tisrdata 30% Tihrdata RID[3:0] CLK Tisrid 30% Tihrid RLAST CLK Tisrlast 30% Tihrlast RRESP[1:0] CLK Tisrresp 30% Tihrresp RVALID CLK Tisrvalid 30% Tihrvalid RREADY CLK Tovrready 30% Tohrready AWADDR[31:0] CLK Tovawaddr 30% Tohawaddr AWBURST[1:0] CLK Tovawburst 30% Tohawburst AWCACHE[3:0] CLK Tovawcache 30% Tohawcache AWID[3:0] CLK Tovawid 30% Tohawid AWLEN[3:0] CLK Tovawlen 30% Tohawlen AWLOCK[1:0] CLK Tovawlock 30% Tohawlock AWPROT[2:0] CLK Tovawprot 30% Tohawprot AWSIZE[2:0] CLK Tovawsize 30% Tohawsize AWVALID CLK Tovawvalid 30% Tohawvalid AWREADY CLK Tisawready 30% Tihawready WDATA[127:0] CLK Tovwdata 30% Tohwdata ARM DDI 0344K Copyright © 2006-2010 ARM Limited. All rights reserved. 17-4 ID060510 Non-Confidential
Page 1 and 2:
Copyright © 2006-2010 ARM Limited.
Page 3 and 4:
Web Address http://www.arm.com ARM
Page 5 and 6:
Contents 2.14 The program status re
Page 7 and 8:
Contents 16.6 Instruction-specific
Page 9 and 10:
List of Tables Table 3-16 Debug Fea
Page 11 and 12:
List of Tables Table 3-136 Secure o
Page 13 and 14:
List of Tables Table 12-59 Values t
Page 15 and 16:
List of Figures Cortex-A8 Technical
Page 17 and 18:
List of Figures Figure 3-77 BTB arr
Page 19 and 20:
List of Figures Figure 15-16 CTI Ch
Page 21 and 22:
About this manual Product revision
Page 23 and 24:
old Highlights interface elements,
Page 25 and 26:
Feedback Feedback on the product Fe
Page 27 and 28:
1.1 About the processor Introductio
Page 29 and 30:
1.3 Components of the processor L1
Page 31 and 32:
1.3.6 NEON 1.3.7 ETM The NEON unit
Page 33 and 34:
1.5 Debug Introduction The processo
Page 35 and 36:
1.7 Configurable options Table 1-1
Page 37 and 38:
Introduction • The various data a
Page 39 and 40:
1.9.6 r2p0-r2p1 1.9.7 r2p1-r2p2 1.9
Page 41 and 42:
Chapter 2 Programmers Model This ch
Page 43 and 44:
2.2 Thumb-2 instruction set Program
Page 45 and 46:
Bits Field Function Programmers Mod
Page 47 and 48:
2.4 Jazelle Extension 2.4.1 Jazelle
Page 49 and 50:
2.5 Security Extensions architectur
Page 51 and 52:
2.6 Advanced SIMD architecture Prog
Page 53 and 54:
2.8 Processor operating states 2.8.
Page 55 and 56:
2.10 Memory formats 2.10.1 Byte-inv
Page 57 and 58:
2.12 Operating modes Programmers Mo
Page 59 and 60:
System and User r0 r1 r2 r3 r4 r5 r
Page 61 and 62:
2.14 The program status registers 2
Page 63 and 64:
2.14.5 The GE[3:0] bits Programmers
Page 65 and 66:
Mode bits Programmers Model M[4:0]
Page 67 and 68:
2.15 Exceptions 2.15.1 Exception en
Page 69 and 70:
2.15.5 Interrupt request 2.15.6 Abo
Page 71 and 72:
This restores both the PC and the C
Page 73 and 74:
2.15.13 Exception priorities Progra
Page 75 and 76:
2.17 Hardware consideration for Sec
Page 77 and 78:
SECMONOUT[78] instruction caches at
Page 79 and 80:
Chapter 3 System Control Coprocesso
Page 81 and 82:
System Control Coprocessor Register
Page 83 and 84:
3.1.3 MMU control and configuration
Page 85 and 86:
3.2 System control coprocessor regi
Page 87 and 88:
CRn Op1 CRm Op2 Register or operati
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
3.2.2 c0, Main ID Register System C
Page 99 and 100:
3.2.4 c0, TCM Type Register 3.2.5 c
Page 101 and 102:
3.2.7 c0, Processor Feature Registe
Page 103 and 104:
• accessible in privileged modes
Page 105 and 106:
System Control Coprocessor Table 3-
Page 107 and 108:
Bits Field Function [11:8] L1 Harva
Page 109 and 110:
Bits Field Function [11:8] Harvard
Page 111 and 112:
31 28 27 24 23 20 19 16 15 12 11 8
Page 113 and 114:
Table 3-30 shows the results of att
Page 115 and 116:
System Control Coprocessor 31 28 27
Page 117 and 118:
Table 3-36 shows the results of att
Page 119 and 120:
• accessible in privileged modes
Page 121 and 122:
CSSR Size 3.2.24 c0, Cache Size Sel
Page 123 and 124:
System Control Coprocessor 31 30 29
Page 125 and 126:
MCR p15, 0, , c1, c0, 0 ; Write Con
Page 127 and 128:
Bits Field [19] Clock stop request
Page 129 and 130:
Bits Field Security State NS S Tabl
Page 131 and 132:
3.2.28 c1, Secure Configuration Reg
Page 133 and 134:
AW EA Function Table 3-55 shows the
Page 135 and 136:
Page 137 and 138:
3.2.32 c2, Translation Table Base R
Page 139 and 140:
System Control Coprocessor Figure 3
Page 141 and 142:
Bits Field Function 3.2.35 c5, Data
Page 143 and 144:
3.2.36 c5, Instruction Fault Status
Page 145 and 146:
3.2.38 c6, Data Fault Address Regis
Page 147 and 148:
System Control Coprocessor Note •
Page 149 and 150:
System Control Coprocessor Figure 3
Page 151 and 152:
Page 153 and 154:
3.2.41 c8, TLB operations The data
Page 155 and 156:
Figure 3-38 shows the bit arrangeme
Page 157 and 158:
EN b 3.2.44 c9, Count Enable Clear
Page 159 and 160:
EN b 3.2.46 c9, Software Increment
Page 161 and 162:
EN b 3.2.48 c9, Cycle Count Registe
Page 163 and 164:
EN b Table 3-96 shows the results o
Page 165 and 166:
Value Description 0x44 Any cacheabl
Page 167 and 168:
DBGEN || NIDEN 3.2.51 c9, User Enab
Page 169 and 170:
EN 3.2.53 c9, Interrupt Enable Clea
Page 171 and 172:
Figure 3-48 shows the bit arrangeme
Page 173 and 174:
3.2.55 c9, L2 Cache Auxiliary Contr
Page 175 and 176:
Bits Field Function [8:6] Tag RAM l
Page 177 and 178:
TL bit value 3.2.57 c10, TLB preloa
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
The PLE Identification and Status R
Page 185 and 186:
Page 187 and 188:
3.2.62 c11, PLE enable commands U b
Page 189 and 190:
Bits Field Function System Control
Page 191 and 192:
U bit PLE bit Table 3-129 shows the
Page 193 and 194:
U bit PLE bit System Control Coproc
Page 195 and 196:
3.2.68 c12, Secure or Nonsecure Vec
Page 197 and 198:
3.2.70 c12, Interrupt Status Regist
Page 199 and 200:
The FCSE PID Register is: • a rea
Page 201 and 202:
Page 203 and 204:
TLB CAM read/write TLB ATTR read/wr
Page 205 and 206:
MCR p15 0, , c15, c3, 4 ; I-L1 TLB
Page 207 and 208:
31 27 26 22 21 0 Reserved L1 Data 0
Page 209 and 210:
System Control Coprocessor The L1 H
Page 211 and 212:
3.2.78 c15, L1 data array operation
Page 213 and 214:
Instruction L1 Data 0 register Inst
Page 215 and 216:
Parity/ECC RAM read/write Data RAM
Page 217 and 218:
3.2.82 c15, L2 parity/ECC array ope
Page 219 and 220:
3.2.84 c15, L2 data array operation
Page 221 and 222:
4.1 About unaligned and mixed-endia
Page 223 and 224:
Unaligned Data and Mixed-endian Dat
Page 225 and 226:
Chapter 5 Program Flow Prediction T
Page 227 and 228:
5.2 Predicted instructions Program
Page 229 and 230:
Program Flow Prediction Because ret
Page 231 and 232:
5.4 Guidelines for optimal performa
Page 233 and 234:
5.6 Operating system and predictor
Page 235 and 236:
6.1 About the MMU Memory Management
Page 237 and 238:
6.3 16MB supersection support Memor
Page 239 and 240:
6.5 External aborts 6.5.1 External
Page 241 and 242:
6.7 MMU software-accessible registe
Page 243 and 244:
7.1 About the L1 memory system Leve
Page 245 and 246:
7.2.6 Instruction cache maintenance
Page 247 and 248:
L1 inner policy a L2 outer policy N
Page 249 and 250:
7.5 Data cache features 7.5.1 Data
Page 251 and 252:
7.7 Hardware support for virtual al
Page 253 and 254:
Chapter 8 Level 2 Memory System Thi
Page 255 and 256:
8.2 Cache organization 8.2.1 L2 cac
Page 257 and 258:
8.3 Enabling and disabling the L2 c
Page 259 and 260:
Level 2 Memory System Note It is en
Page 261 and 262:
Level 2 Memory System Note You must
Page 263 and 264:
Lock address : LockAddr Lock free :
Page 265 and 266:
8.7 Parity and error correction cod
Page 267 and 268:
9.1 About the external memory inter
Page 269 and 270:
Integer data and CP14 writes Noncac
Page 271 and 272:
9.4 AXI data read/write transaction
Page 273 and 274:
Noncacheable, or strongly ordered,
Page 275 and 276:
Noncacheable store word Noncacheabl
Page 277 and 278:
LA Last Access External Memory Inte
Page 279 and 280:
10.1 Clock domains 10.1.1 AXI clock
Page 281 and 282:
10.2 Reset domains 10.2.1 Power-on
Page 283 and 284:
REFCLK (PLL input) nPORESET ARESETn
Page 285 and 286:
10.3 Power control 10.3.1 Dynamic p
Page 287 and 288:
Clock, Reset, and Power Control the
Page 289 and 290:
ATB APB I/O clamp I/O clamp L/S = L
Page 291 and 292:
ATB APB I/O clamp I/O clamp LS = Le
Page 293 and 294:
Clock, Reset, and Power Control 3.
Page 295 and 296:
Powering up the debug and ETM domai
Page 297 and 298:
7. Perform a normal software reset
Page 299 and 300:
Clock, Reset, and Power Control 5.
Page 301 and 302:
Chapter 11 Design for Test This cha
Page 303 and 304:
In L1 MBIST Instruction Register Fi
Page 305 and 306:
Note Do not test the CAMBIST arrays
Page 307 and 308:
• number of rows of the L2 data,
Page 309 and 310:
Design for Test Not all row setting
Page 311 and 312:
In Design for Test Figure 11-4 show
Page 313 and 314:
Design for Test When testing the ta
Page 315 and 316:
CLK ARESETn MBISTMODE MBISTSHIFT MB
Page 317 and 318:
End-of-test datalog retrieval Desig
Page 319 and 320:
Pattern N RWRXMARCH 8N Row-fast Sta
Page 321 and 322:
4. rscan array, data_seed = invert.
Page 323 and 324:
3. R_, W, R, decr. 4. rscan data fr
Page 325 and 326:
• the data after pass 1 of XADDRB
Page 327 and 328:
(1 + (2 17)) 2 17 = 4,587,520 cycle
Page 329 and 330:
processor input ports WEXTEST WINTE
Page 331 and 332:
Design for Test toggling during shi
Page 333 and 334:
12.1 Debug systems 12.1.1 Debug hos
Page 335 and 336:
12.2.3 Security extensions and debu
Page 337 and 338:
Instruction Mnemonic Description 12
Page 339 and 340:
12.3.6 Power domains and debug 12.3
Page 341 and 342:
Table 12-5 shows the APB interface
Page 343 and 344:
12.4 Debug register descriptions Te
Page 345 and 346:
MRC p14, 0, , c0, c0, 0 ; Read Debu
Page 347 and 348:
31 30 29 28 27 26 25 24 23 22 21 20
Page 349 and 350:
Bits Field Function [21:20] DTR acc
Page 351 and 352:
Bits Field Function To access the D
Page 353 and 354:
12.4.7 Watchpoint Fault Address Reg
Page 355 and 356:
Bits Access Normal address [2] RW V
Page 357 and 358:
12.4.12 Debug Run Control Register
Page 359 and 360:
Table 12-23 shows how the bit value
Page 361 and 362:
BVR[22:20] Meaning b011 The corresp
Page 363 and 364:
Bits Field Function [15:14] Secure
Page 365 and 366:
12.4.18 Operating System Lock Statu
Page 367 and 368:
Debug • The sequence can be aband
Page 369 and 370:
12.5 Management registers Offset Th
Page 371 and 372:
Offset Register number Mnemonic Fun
Page 373 and 374:
Bits Field Function [5] nDMAIRQ nDM
Page 375 and 376:
12.5.7 Claim Tag Clear Register 12.
Page 377 and 378:
12.5.10 Authentication Status Regis
Page 379 and 380:
Table 12-45 shows fields that are i
Page 381 and 382:
12.6 Debug events 12.6.1 Software d
Page 383 and 384:
12.6.5 Watchpoint debug events If a
Page 385 and 386:
Table 12-53 shows the values in the
Page 387 and 388:
12.8 Debug state 12.8.1 Entering de
Page 389 and 390:
12.8.4 Writing to the CPSR in debug
Page 391 and 392:
Mode SCR[0] For CP15 instructions,
Page 393 and 394:
12.8.9 Leaving debug state Imprecis
Page 395 and 396:
12.9.3 Cache usage profiling Debug
Page 397 and 398:
Note DBGPWRDWNREQ must be tied LOW
Page 399 and 400:
If software running on the processo
Page 401 and 402:
Rules for accessing the DCC At the
Page 403 and 404:
} While the processor is running, i
Page 405 and 406:
Debug Table 12-59 Values to write t
Page 407 and 408:
12.11.4 Debug state entry Example 1
Page 409 and 410:
} // Step 1. Update the CPSR value
Page 411 and 412:
Writing the CPSR in debug state Exa
Page 413 and 414:
Debug Example 12-21 Reading a word
Page 415 and 416:
} // Step 9. Check for aborts. abor
Page 417 and 418:
12.12 Debugging systems with energy
Page 419 and 420:
MOV r0, r4 POP {r4, pc} Example 12-
Page 421 and 422:
Chapter 13 NEON and VFP Programmers
Page 423 and 424:
13.2 General-purpose registers 13.2
Page 425 and 426:
13.3 Short vectors 13.3.1 About reg
Page 427 and 428:
13.3.2 Operations using register ba
Page 429 and 430:
NEON and VFP Programmers Model The
Page 431 and 432:
Note All hardware ID information is
Page 433 and 434:
Bits Field Function [12:8] - Reserv
Page 435 and 436:
NEON and VFP Programmers Model Tabl
Page 437 and 438:
13.6 Compliance with the IEEE 754 s
Page 439 and 440:
Underflow NEON and VFP Programmers
Page 441 and 442:
14.1 About the ETM 14.1.1 ETM featu
Page 443 and 444:
14.1.3 NEON Bridge and bus matrix A
Page 445 and 446:
14.3 ETM register summary The ETM r
Page 447 and 448:
Bits Field Function [11:8] Major ET
Page 449 and 450:
14.4.4 Peripheral Identification Re
Page 451 and 452:
See the ETM Architecture Specificat
Page 453 and 454:
Embedded Trace Macrocell Table 14-1
Page 455 and 456:
Page 457 and 458:
14.5.3 Enabling events 14.5.4 Addre
Page 459 and 460:
14.7 Context ID tracing Embedded Tr
Page 461 and 462:
14.9 Idle state control Embedded Tr
Page 463 and 464:
Page 465 and 466:
Chapter 15 Cross Trigger Interface
Page 467 and 468:
CTICHIN[0] CTICHIN[1] CTICHIN[2] CT
Page 469 and 470:
15.2 Trigger inputs and outputs Tri
Page 471 and 472:
15.3 Connecting asynchronous channe
Page 473 and 474:
15.5 CTI register summary Address o
Page 475 and 476:
15.6 CTI register descriptions This
Page 477 and 478:
15.6.4 CTI Application Trigger Clea
Page 479 and 480:
Table 15-10 shows how the bit value
Page 481 and 482: 15.6.12 ASIC Control Register, ASIC
Page 483 and 484: 15.7 CTI Integration Test Registers
Page 485 and 486: 15.7.4 ITTRIGOUTACK, 0xEF0 15.7.5 I
Page 487 and 488: Cross Trigger Interface Table 15-26
Page 489 and 490: 15.8.3 Device Type Identifier, 0xFC
Page 491 and 492: Cross Trigger Interface Table 15-31
Page 493 and 494: 16.1 About instruction cycle timing
Page 495 and 496: Instruction Cycle Timing Example 16
Page 497 and 498: Table 16-4 shows the operation of m
Page 499 and 500: Table 16-9 shows the operation of l
Page 501 and 502: d. See Load/store instructions on p
Page 503 and 504: Instruction Cycle Timing Table 16-1
Page 505 and 506: 16.4 Other pipeline-dependent laten
Page 507 and 508: 16.4.5 Conditional instructions Ins
Page 509 and 510: 16.6 Instruction-specific schedulin
Page 511 and 512: Instruction Cycle Timing VNEG Dd,Dm
Page 513 and 514: VMLA a VMLS a VMLAa VMLSa VQDMLAa V
Page 515 and 516: VSLI VSRI 16.6.5 Advanced SIMD floa
Page 517 and 518: 16.6.6 Advanced SIMD byte permute i
Page 519 and 520: Instruction Table 16-23 shows the o
Page 521 and 522: Instruction VST3 3-reg (unaligned)
Page 523 and 524: Instruction VLD3 3-reg (unaligned)
Page 525 and 526: Instruction Single precision cycles
Page 527 and 528: • FMACS, FNMACS • FMSCS, FNMSCS
Page 529 and 530: is dual issued with previous instru
Page 531: 17.1 About setup and hold times AC
Page 535 and 536: 17.3 ATB and CTI interfaces Table 1
Page 537 and 538: AC Characteristics Table 17-4 Timin
Page 539 and 540: 17.6 L2 preload interface AC Charac
Page 541 and 542: 17.8 Miscellaneous signals AC Chara
Page 543 and 544: A.1 AXI interface Signal Descriptio
Page 545 and 546: A.3 MBIST and DFT interface A.3.1 M
Page 547 and 548: A.4 Preload engine interface Table
Page 549 and 550: A.6 Miscellaneous signals Table A-7
Page 551 and 552: Signal I/O Reset Description CFGNMF
Page 553 and 554: Signal I/O Reset Description DBGNOP
Page 555 and 556: Appendix B Instruction Mnemonics Th
Page 557 and 558: Instruction Mnemonics Table B-1 Adv
Page 559 and 560: Appendix C Revisions This appendix
Page 561 and 562: Revisions Added text to clarify des
Page 563 and 564: Glossary This glossary describes so
Page 565 and 566: Glossary Automatic Test Pattern Gen
Page 567 and 568: Big-endian memory Memory in which:
Page 569 and 570: Conditional execution Glossary incl
Page 571 and 572: Glossary Embedded Trace Macrocell (
Page 573 and 574: Illegal instruction An instruction
Page 575 and 576: Glossary NaN Not a number. A symbol
Page 577 and 578: Glossary Significand The component
Page 579 and 580: Glossary Watchpoint A watchpoint is
show all

Cortex-A8 Technical Reference Manual - ARM Information Center

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?