Rexroth IndraDrive C Drive Controllers HCS02.1 ... - Bosch Rexroth

Rexroth IndraDrive Electrical Data 5-15
5.3 Additional Components
Mains Filter HNF
DOK-INDRV*-FU*********-IB01-EN-P
Unit
F240-E0051
M900-E0051
F240-E0125
M900-E0125
HNF01.1A- … -A-480-NNNN
Power dissipation W < 89 < 91 < 127 < 174 < 238 < 373 < 73 < 77 < 163 < 157 < 135 < 146
Phase current (continuous
current)
Phase current (peak
current 1) )
Leakage current at filters
input (line side)
Leakage current at filters
output (load side)
allowed THD (Total Harmonic
Distortion)
Reduction of allowed
operating data due to
harmonic content
F240-E0202
M900-E0202
A 51 51 125 125 202 202 26 26 65 65 94 94
A 77 77 188 188 303 303 65 65 163 163 235 235
A < 2 < 2 < 2,2 < 2,2 < 2,5 < 2,5 < 2 < 2 < 2 < 2 < 2,2 < 2,2
A < 2 < 2 < 2,2 < 2,2 < 2,5 < 2,5 < 2 < 2 < 2 < 2 < 2,2 < 2,2
% see Project Planning Manual "Rexroth IndraDrive Drive System"
- see Project Planning Manual "Rexroth IndraDrive Drive System"
Input supply voltage V 3 x AC 380…480V ±10%, 50/60Hz ±2%
Sum of leakage currents at
filters input with power supply
unit switched off:
• 1 phase failed
• 2 phases failed
Leakage resistance (Phase –
Ground)
A
MOhm > 15
Protection category - IP20
• < 0,83
• < 1,4
Materials - free of asbestos and silicone
Terminal L1, L2, L3 resp. L1.1, L2.1, L3.1:
Cross section flexible min. mm 2
Cross section flexible max. mm 2
Cross section rigid min. mm 2
Cross section rigid max. mm 2
0,5 0,5 16 16 50 50 0,5 0,5 10 10 16 16
16 16 50 50 150 150 10 10 25 25 50 50
0,5 0,5 16 16 35 35 0,5 0,5 6 6 16 16
25 25 50 50 150 150 16 16 35 35 50 50
Cross section AWG min. -- 20 20 6 6 2 2 20 20 10 10 6 6
Cross section AWG max. -- 4 4 0 0 00/3 00/3 6 6 2 2 0 0
Tightening torque Nm
4,8
±0,5
4,8
±0,5
< 25 < 25 < 25 < 25
F240-R0026
4,8
±0,5
1) duration: 300 ms ;
cycle duration:
for feeding units: 0,67 s;
for regenerating units: 1,42 s;
base load: 60% (continuous current)
Fig. 5-24: Data HNF
M900-R0026
4,8
±0,5
F240-R0065
4,8
±0,5
M900-R0065
4,8
±0,5
F240-R0094
M900-R0094
< 25 < 25