GeniusPro/Lightpalette Operator's Manual - Strand Lighting

GeniusPro/Lightpalette Operator's Manual
Additional software features on version v2.5k
- PS/2 mouse now reliable on all consoles. After changing in User
Setup need to wait 2 seconds before mouse will operate.
- 510i P3 key working again.
- Fix startup delay on 300 consoles when network set to on.
Additional software features on version v2.5e
- Tracked cues with zero level in non first part load correctly.
- Channels In Use printout corrected.
Additional software features on version v2.5d
- Only active channels set via HandHeldRemote are ignored on
Update except if it is the HHR doing the updating in which case
they are used. Previous HHR selections are Updated. In this way all
'red' channels are updated.
Additional software features on version v2.5c
- DMX level of 1 is now shown as 1% rather than 0%.
- Channel control channels at 0% are now added when updating
into non tracking cues, groups & submasters. Use CHANSIN to
stop new channels from being added.
- Support iPAQ WiFi hand held remote.
- Attribute names have changed to better reflect their use. See
fixture.lib for details.
Additional software features on version v2.5b
- PS/2 mouse support added for 300 consoles.
- RECORD & UPDATE now use levels after applying Grandmasters
& Inhibitive Submasters. REC-SUBS uses levels before.
Additional software features on version v2.5a
- After CLR channels can no longer be reselected using @ key.
PLUS & MINUS still work though.
i.e. (Direct 1 digit) 1 @ 5 CLR @ 6 Now doesn't work
1 @ 5 CLR + 2 @ 6 Still works
- Preview selection retained (cue/sub/group/effect):
CUE q CUE_PREVIEW Display cue q on preview
CUE CUE_PREVIEW Display 'current' cue in preview
CUE_PREVIEW Display last previewed cue
- Leds on 300 display selection keys correct.
- Can now select show 5 from the Login display.
- Ensure network DMX & Video is not processed if destined for a
different subnet.
- Cue Summary display shows part channel information (zero
counts are shown as blank)
- Attribute values > dmx 250 always record/update correctly.
- Recording/updating Cue QOnly correctly preserves the following
multi part cue block info. All new channels are added to the first
part.
- Can now delete the highest channel number in the show.
- RELOADx1/2 recreates a tracking cue as per CUE q LOADx1/2.
- Channels set via HandHeldRemote are not Updated - only
channels set via console channel control are updated (unless of
course a leading channel list is specified).
- Loading cues from disk when in a Tracking mode load QOnly to
ensure loaded cue state preserved.
- Mouse controls all attributes in preview. Left/Right buttons are
used for Minus/Plus when on an edit field & to change to the
previous/next attribute when a channel is selected.
- Shift RemDim on output rem dim's but excludes subs - as LP90
- 300 DMX output disabled if tracking backup & not in control.
- After Cue Copy the X playback last recorded cue is updated.
The [@ATT] key (500 Series consoles) is equivalent to the
[ATTRIB] key on 300 Series consoles. This manual refers to
[@ATT]
Configuring European Keyboards
The console is configured at the factory for the US ASCII keyboard.
You need to configure keyboards for other locales.
Refer to Country Keyboard Support
Technical Assistance
The console requires a minimum of maintenance and servicing.
If equipment fails to operate properly upon installation, or under
normal load and temperature conditions, and basic troubleshooting
procedures are not effective, please contact your nearest Strand
Authorised Service Centre or Strand Lighting Field Service at the
office serving your area.
For technical questions regarding setup, operation, or maintenance
of this equipment, please contact your nearest Strand Authorised
Service Centre or the Strand Lighting Field Service office serving
your area.
For purchase of upgrades, accessories, peripherals or
documentation, please contact your nearest Strand Authorised
Service Centre or the Strand Lighting office serving your area.
For comments regarding equipment functions and possible
improvements, or for comments on these instructions, please write to
the Strand Lighting office serving your area.
You can access the Strand Lighting World Wide Web site at http://
www.strandlighting.com/
Addresses for all of the Strand Lighting offices are as shown:
Phone numbers do not include country code or other international
access data.
Asia: 7th Floor, Corporation Sq, 8 Lam Lok St, Kowloon Bay,
Kowloon, Hong Kong Tel: 757 3033 Fax: 757 1767
Canada: 2430 Lucknow Dr., Unit 15, Mississauga, Ontario L5S 1V3
Canada Tel: 905 677 7130 Fax: 905 677 6859
Germany: Ullsteinstrasse 114-142, 12109 Berlin Tel: 004930 707
9510 Fax: 004930 707 95199
Italy: Via delle Gardenie 33 (Pontia Vecchia KM 33,400), 00040
Pomezia-Roma, Italy Tel: 6914 7123 Fax: 6914 7136
U.K.: Strand Lighting Ltd. Mitchelston Industrial Estate, Kirkcaldy,
Fife KY1 3LY, Scotland. Tel 01592 652333 Fax 01592 653528
U.S.A Service & Support 800 4 STRAND (800 478 7263)
U.S.A.: 18111 South Santa Fe Ave., Rancho Dominguez, CA 90221
USA Tel: 310 637 7500 Fax: .310 632 5519
The information in this manual is for information purposes only and is
subject to change without notice. Strand Lighting assumes no
responsibility for any errors or omissions which may appear in this
manual. For comments and suggestions regarding corrections and/or
file:///C|/LIGHTP/HELP.ENG/INDEX.HTM (7 of 11)11/2/2004 3:02:16 AM