Cortex-A8 R2P2.pdf - ARM Information Center

More documents

Recommendations

Info

Level 2 Memory SystemNoteYou must enable the MMU for the PLE to operate. If you disabled the MMU duringpreloading engine configurations, the PLE treats all memory as noncacheableregardless of the state of the Memory Region Remap Registers.8.4.6 Effects of cache maintenance operations during preloading engine transfersWhen a CP15 operation is performed during a preloading engine transfer, the preloadengine pauses the transfer of data and waits for all outstanding AXI transactions tocomplete. Following completion of the CP15 operation, the preload engine restarts.8-10 Copyright © 2006-2008 ARM Limited. All rights reserved. ARM DDI 0344E
Level 2 Memory System8.5 Synchronization primitivesOn previous versions of the ARM architectures, support for shared memorysynchronization was with the read-locked-write operations that swap register contentswith memory, the SWP and SWPB instructions. These support basic busy and freesemaphore mechanisms. See the ARM Architecture Reference Manual for details of theswap instructions.ARMv7-A describes support for more comprehensive shared-memory synchronizationprimitives that scale for multiple-processor system designs. Two sets of instructions areintroduced to support multiple-processor and shared-memory inter-processcommunication:• load-exclusive, LDR{B,H,D}EX• store-exclusive, STR{B,H,D}EX.The exclusive-access instructions rely on the ability to tag a physical address asexclusive-access for a particular processor. This tag is later used to determine if anexclusive store to an address occurs.For nonshared memory regions, the LDR{B,H,D}EX and STR{B,H,D}EX instructions arepresented to the ports as normal LDR or STR. If a processor does an STR on a memoryregion that it has already marked as exclusive, this does not clear the tag. However, ifthe region has been marked by another processor, an STR clears the tag.Other events might cause the tag to be cleared. In particular, for memory regions thatare not shared, it is Unpredictable whether a store by another processor to a taggedphysical address causes the tag to be cleared.An external abort on either a load-exclusive or store-exclusive puts the processor intoAbort mode.NoteAn external abort on a load-exclusive can leave the processor internal monitor in itsexclusive state and might affect your software. If it does, you must execute astore-exclusive to an unused location in your abort handler or use the CLREX instructionto clear the processor internal monitor to an open state.8.5.1 Load-exclusive instructionLoad-exclusive performs a load from memory and causes the physical address of theaccess to be tagged as exclusive-access for the requesting processor. This causes anyother physical address that has been tagged by the requesting processor to no longer betagged as exclusive-access.ARM DDI 0344E Copyright © 2006-2008 ARM Limited. All rights reserved. 8-11
Page 1 and 2:
Cortex -A8Revision: r2p2Technical R
Page 3 and 4:
Product StatusThe information in th
Page 5 and 6:
ContentsCortex-A8 Technical Referen
Page 7 and 8:
Contents7.8 Parity detection ......
Page 9 and 10:
ContentsA.2 ATB interface .........
Page 11 and 12:
List of TablesCortex-A8 Technical R
Page 14 and 15:
List of TablesTable 3-103 Results o
Page 16 and 17:
List of TablesTable 12-1 Access to
Page 18 and 19:
List of TablesTable 15-3 CTI regist
Page 20 and 21:
List of Tablesxx Copyright © 2006-
Page 22 and 23:
List of FiguresFigure 3-10 Memory M
Page 24 and 25:
List of FiguresFigure 10-13 Retenti
Page 26 and 27:
List of FiguresFigure 15-16 CTI Cha
Page 28 and 29:
PrefaceAbout this manualThis is the
Page 30 and 31:
PrefaceChapter 16 Instruction Cycle
Page 32 and 33:
PrefacePrefix CPrefix HPrefix nPref
Page 34 and 35:
PrefaceFeedbackARM welcomes feedbac
Page 36 and 37:
Introduction1.1 About the processor
Page 38 and 39:
Introduction1.3 Components of the p
Page 40 and 41:
Introduction1.3.4 Load/storeThe loa
Page 42 and 43:
Introduction1.4 External interfaces
Page 44 and 45:
Introduction1.6 Power managementThe
Page 46 and 47:
Introduction1.8 Product revisionsTh
Page 48 and 49:
Introduction1-14 Copyright © 2006-
Page 50 and 51:
Programmer’s Model• Hardware co
Page 52 and 53:
Programmer’s Model2.2 Thumb-2 ins
Page 54 and 55:
Programmer’s Model2.3 ThumbEE ins
Page 56 and 57:
Programmer’s ModelThumbEE Handler
Page 58 and 59:
Programmer’s Model2.4 Jazelle Ext
Page 60 and 61:
Programmer’s Model— the registe
Page 62 and 63:
Programmer’s ModelNonsecureSecure
Page 64 and 65:
Programmer’s Model2.7 VFPv3 archi
Page 66 and 67:
Programmer’s Model2.9 Data typesT
Page 68 and 69:
Programmer’s ModelBitHigher addre
Page 70 and 71:
Programmer’s Model2.12 Operating
Page 72 and 73:
Programmer’s ModelIn privileged m
Page 74 and 75:
Programmer’s Model16 generalpurpo
Page 76 and 77:
Programmer’s ModelIn ARM state, y
Page 78 and 79:
Programmer’s Model2.14.5 The GE[3
Page 80 and 81:
Programmer’s ModelT bitThe T bit
Page 82 and 83:
Programmer’s ModelOnly secure pri
Page 84 and 85:
Programmer’s Model2.15.2 Leaving
Page 86 and 87:
Programmer’s ModelAn internal or
Page 88 and 89:
Programmer’s ModelImprecise data
Page 90 and 91:
Programmer’s ModelNoteIf the Embe
Page 92 and 93:
Programmer’s Model2.16 Software c
Page 94 and 95:
Programmer’s Model2.17.2 Security
Page 96 and 97:
Programmer’s Model2.18 Control co
Page 98 and 99:
System Control Coprocessor3.1 About
Page 100 and 101:
System Control CoprocessorTable 3-1
Page 102 and 103:
System Control CoprocessorSecurity
Page 104 and 105:
System Control Coprocessor3.1.6 Sys
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
System Control CoprocessorThe TCM T
Page 126 and 127:
Page 128 and 129:
System Control CoprocessorFigure 3-
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
System Control Coprocessor31 28 27
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
System Control Coprocessor3.2.20 c0
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
System Control Coprocessora. An ent
Page 156 and 157:
Page 158 and 159:
System Control CoprocessorThe Auxil
Page 160 and 161:
System Control CoprocessorBits Fiel
Page 162 and 163:
Page 164 and 165:
System Control Coprocessora. n is t
Page 166 and 167:
Page 168 and 169:
Page 170 and 171:
Page 172 and 173:
Page 174 and 175:
Page 176 and 177:
Page 178:
Page 181 and 182:
System Control CoprocessorMRC p15,
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
System Control CoprocessorVA to PA
Page 195 and 196:
Page 197 and 198:
System Control CoprocessorInvalidat
Page 199 and 200:
System Control CoprocessorThe PMNC
Page 201 and 202:
System Control CoprocessorCWhen wri
Page 203 and 204:
Page 205 and 206:
Page 207 and 208:
Page 209 and 210:
Page 211 and 212:
Page 213 and 214:
System Control Coprocessorb. The EN
Page 215 and 216:
System Control CoprocessorCWhen rea
Page 217 and 218:
Page 219 and 220:
Page 221 and 222:
System Control Coprocessor• acces
Page 223 and 224:
Page 225 and 226:
System Control CoprocessorYou can c
Page 227 and 228:
System Control CoprocessorIf the op
Page 229 and 230:
Page 231 and 232:
Page 233 and 234:
System Control CoprocessorTo access
Page 235 and 236:
Page 237 and 238:
System Control Coprocessora. An ent
Page 239 and 240:
Page 241 and 242:
Page 243 and 244:
System Control CoprocessorTo access
Page 245 and 246:
System Control CoprocessorThe PLE I
Page 247 and 248:
Page 249 and 250:
Page 251 and 252:
Page 253 and 254:
Page 255 and 256:
Page 257 and 258:
Page 259 and 260:
Page 261 and 262:
Page 263 and 264:
System Control CoprocessorTo perfor
Page 265 and 266:
Page 267 and 268:
System Control CoprocessorLDR R1, =
Page 269 and 270:
System Control CoprocessorLDR R1, =
Page 271 and 272:
System Control CoprocessorL1 Data 0
Page 273 and 274:
System Control CoprocessorInstructi
Page 275 and 276:
System Control CoprocessorParity/EC
Page 277 and 278:
Page 279 and 280: System Control CoprocessorL2 parity
Page 281 and 282: System Control CoprocessorThe L2 da
Page 283 and 284: Chapter 4Unaligned Data and Mixed-e
Page 285 and 286: Unaligned Data and Mixed-endian Dat
Page 287 and 288: Unaligned Data and Mixed-endian Dat
Page 289 and 290: Chapter 5Program Flow PredictionThi
Page 291 and 292: Program Flow Prediction5.2 Predicte
Page 293 and 294: Program Flow Prediction5.2.1 Return
Page 295 and 296: Program Flow Prediction5.4 Guidelin
Page 297 and 298: Program Flow Prediction5.6 Operatin
Page 299 and 300: Chapter 6Memory Management UnitThis
Page 301 and 302: Memory Management Unit6.2 Memory ac
Page 303 and 304: Memory Management Unit6.4 MMU inter
Page 305 and 306: Memory Management Unit6.6 TLB lockd
Page 307 and 308: Chapter 7Level 1 Memory SystemThis
Page 309 and 310: Level 1 Memory System7.2 Cache orga
Page 311 and 312: Level 1 Memory System7.3 Memory att
Page 313 and 314: Level 1 Memory SystemTable 7-1 Memo
Page 315 and 316: Level 1 Memory System7.5 Data cache
Page 317 and 318: Level 1 Memory SystemAn exception t
Page 319 and 320: Level 1 Memory System7.8 Parity det
Page 321 and 322: Chapter 8Level 2 Memory SystemThis
Page 323 and 324: Level 2 Memory System8.2 Cache orga
Page 325 and 326: Level 2 Memory System8.3 Enabling a
Page 327 and 328: Level 2 Memory SystemControl Regist
Page 329: Level 2 Memory System8.4.4 Memory r
Page 333 and 334: Level 2 Memory System8.6 Locked acc
Page 335 and 336: Chapter 9External Memory InterfaceT
Page 337 and 338: External Memory Interfaceto the wri
Page 339 and 340: External Memory InterfaceTable 9-2
Page 341 and 342: External Memory Interface9.3 AXI in
Page 343 and 344: External Memory InterfaceBWBCNoTTSS
Page 353 and 354: Chapter 10Clock, Reset, and Power C
Page 355 and 356: Clock, Reset, and Power Controlfami
Page 357 and 358: Clock, Reset, and Power Control10.2
Page 359 and 360: Clock, Reset, and Power Control•
Page 361 and 362: Clock, Reset, and Power Control2. F
Page 363 and 364: Clock, Reset, and Power ControlNote
Page 365 and 366: Clock, Reset, and Power ControlAfte
Page 367 and 368: Clock, Reset, and Power Control•
Page 369 and 370: Clock, Reset, and Power Control—
Page 371 and 372: Clock, Reset, and Power ControlThe
Page 373 and 374: Clock, Reset, and Power ControlPowe
Page 375 and 376: Clock, Reset, and Power ControlTo p
Page 377 and 378: Clock, Reset, and Power ControlPowe
Page 379 and 380: Clock, Reset, and Power ControlATBI
Page 381 and 382:
Clock, Reset, and Power Control7. P
Page 383 and 384:
Chapter 11Design for TestThis chapt
Page 385 and 386:
Design for Test11.1.2 MBIST registe
Page 387 and 388:
Design for Testdseed[3:0]Write the
Page 389 and 390:
Design for TestNoteOnly arrays with
Page 391 and 392:
Design for Test• read and write l
Page 393 and 394:
Design for TestTable 11-10 Selectin
Page 395 and 396:
Design for TestTable 11-15 shows ho
Page 397 and 398:
Design for TestArrayFail[22:0] fail
Page 399 and 400:
Design for TestWhen testing the tag
Page 401 and 402:
Design for Test• Bitmap test mode
Page 403 and 404:
Design for TestCLKARESETnMBISTMODEM
Page 405 and 406:
Design for TestCLKARESETnMBISTMODEM
Page 407 and 408:
Design for TestTable 11-19 shows th
Page 409 and 410:
Design for TestNoteNormal MBIST tes
Page 411 and 412:
Design for TestRowmaxmax - 11 1 1 1
Page 413 and 414:
Design for Test2. R, W_, R_, incr.3
Page 415 and 416:
Design for TestRow3210Addressingdir
Page 417 and 418:
Design for TestRow32100 00 00 00 00
Page 419 and 420:
Design for Test11.2 ATPG test featu
Page 421 and 422:
Design for TestWBR in place of the
Page 423 and 424:
Design for TestOne methodology for
Page 425 and 426:
Chapter 12DebugThis chapter describ
Page 427 and 428:
Debug12.1.3 Debug targetThe debug t
Page 429 and 430:
DebugWhen execution of a monitor ta
Page 431 and 432:
Debug12.3 Debug register interfaceY
Page 433 and 434:
DebugTable 12-3 Debug memory-mapped
Page 435 and 436:
Debug12.3.6 Power domains and debug
Page 437 and 438:
DebugLocks permissionYou can lock t
Page 439 and 440:
DebugTable 12-6 shows the behavior
Page 441 and 442:
Debug12.4 Debug register descriptio
Page 443 and 444:
DebugTable 12-11 shows how the bit
Page 445 and 446:
DebugThe Debug Self Address Offset
Page 447 and 448:
DebugBits Field FunctionTable 12-14
Page 449 and 450:
Page 451 and 452:
DebugBits Field Function[9] - Reser
Page 453 and 454:
DebugThe DTR access mode can be one
Page 455 and 456:
DebugBitsFieldFunctionTable 12-16 s
Page 457 and 458:
DebugTable 12-17 Vector Catch Regis
Page 459 and 460:
Debug31 3 2 1 0ReservedNot write-th
Page 461 and 462:
Page 463 and 464:
Page 465 and 466:
DebugTable 12-23 Breakpoint Control
Page 467 and 468:
Debug12.4.16 Watchpoint Control Reg
Page 469 and 470:
DebugTable 12-26 Watchpoint Control
Page 471 and 472:
Page 473 and 474:
Page 475 and 476:
Page 477 and 478:
DebugNoteOn system reset, PRSR[1] r
Page 479 and 480:
DebugTable 12-32 Management registe
Page 481 and 482:
DebugFigure 12-19 shows the bit arr
Page 483 and 484:
Page 485 and 486:
Debug12.5.5 Integration Mode Contro
Page 487 and 488:
Debug12.5.8 Lock Access RegisterThe
Page 489 and 490:
Debug31 8 7 6 5 4 3 2 1 0ReservedSe
Page 491 and 492:
DebugTable 12-44 Peripheral Identif
Page 493 and 494:
DebugTable 12-50 shows how the bit
Page 495 and 496:
Debug12.6.2 Halting debug event•
Page 497 and 498:
Debug12.6.5 Watchpoint debug events
Page 499 and 500:
DebugNoteThe Data Abort handler che
Page 501 and 502:
DebugIf the debugged code is not ru
Page 503 and 504:
DebugTable 12-54 shows the read PC
Page 505 and 506:
Debug12.8.4 Writing to the CPSR in
Page 507 and 508:
DebugCoprocessor instructionsThe ru
Page 509 and 510:
DebugSVCSMCUndefinedThe processor i
Page 511 and 512:
Debug12.9 Cache debugThere are seve
Page 513 and 514:
Debug12.10 External debug interface
Page 515 and 516:
DebugDBGROMADDRThe DBGROMADDR signa
Page 517 and 518:
Debug4. Issue an Instruction Synchr
Page 519 and 520:
Debug12.11.1 Debug communications c
Page 521 and 522:
DebugDebugger access to the DCCA de
Page 523 and 524:
DebugTable 12-58 Values to write to
Page 525 and 526:
Debug}when 1:byte_address_select :=
Page 527 and 528:
DebugNoteIn Example 12-10 on page 1
Page 529 and 530:
Debug12.11.5 Debug state exitWhen e
Page 531 and 532:
DebugExample 12-15 Reading the PCRe
Page 533 and 534:
DebugExample 12-19 Checking for an
Page 535 and 536:
DebugExample 12-22 shows the sequen
Page 537 and 538:
Debug}dscr := ReadDebugRegister(34)
Page 539 and 540:
Debug}scr := (scr | 1);WriteCPReg(1
Page 541 and 542:
DebugIf on a power-down request fro
Page 543 and 544:
Debug; Step 2. Loop writing words f
Page 545 and 546:
Chapter 13NEON and VFP Programmer
Page 547 and 548:
NEON and VFP Programmer’s Modelre
Page 549 and 550:
NEON and VFP Programmer’s ModelS0
Page 551 and 552:
NEON and VFP Programmer’s ModelBa
Page 553 and 554:
NEON and VFP Programmer’s ModelFC
Page 555 and 556:
NEON and VFP Programmer’s ModelTa
Page 557 and 558:
Page 559 and 560:
NEON and VFP Programmer’s Model31
Page 561 and 562:
NEON and VFP Programmer’s ModelTh
Page 563 and 564:
Page 565 and 566:
Page 567 and 568:
Page 569 and 570:
NEON and VFP Programmer’s ModelCo
Page 571 and 572:
Chapter 14Embedded Trace MacrocellT
Page 573 and 574:
Embedded Trace Macrocell14.1.2 The
Page 575 and 576:
Embedded Trace Macrocell(DAP) throu
Page 577 and 578:
Embedded Trace MacrocellTable 14-1
Page 579 and 580:
Embedded Trace MacrocellRegister na
Page 581 and 582:
Page 583 and 584:
Page 585 and 586:
Page 587 and 588:
Embedded Trace MacrocellSee the ETM
Page 589 and 590:
Page 591 and 592:
Page 593 and 594:
Embedded Trace Macrocell14.5 Precis
Page 595 and 596:
Embedded Trace MacrocellThe followi
Page 597 and 598:
Embedded Trace Macrocellcomparator
Page 599 and 600:
Embedded Trace Macrocell14.8 Instru
Page 601 and 602:
Embedded Trace MacrocellWhen a WFI
Page 603 and 604:
Page 605 and 606:
Embedded Trace MacrocellYou can use
Page 607 and 608:
Chapter 15Cross Trigger InterfaceTh
Page 609 and 610:
Cross Trigger Interface• An input
Page 611 and 612:
Cross Trigger Interface15.1.2 The c
Page 613 and 614:
Cross Trigger InterfaceTable 15-2 T
Page 615 and 616:
Cross Trigger Interface15.4 About t
Page 617 and 618:
Cross Trigger InterfaceTable 15-3 C
Page 619 and 620:
Cross Trigger Interface15.6 CTI reg
Page 621 and 622:
Cross Trigger InterfaceNoteThe CTII
Page 623 and 624:
Cross Trigger InterfaceBits Field F
Page 625 and 626:
Cross Trigger Interface15.6.9 CTI T
Page 627 and 628:
Cross Trigger InterfaceTable 15-14
Page 629 and 630:
Page 631 and 632:
Page 633 and 634:
Cross Trigger Interface15.7.4 ITTRI
Page 635 and 636:
Page 637 and 638:
Cross Trigger Interface15.8.3 Devic
Page 639 and 640:
Cross Trigger InterfaceActual Compo
Page 641 and 642:
Chapter 16Instruction Cycle TimingT
Page 643 and 644:
Instruction Cycle Timing16.2 Instru
Page 645 and 646:
Instruction Cycle Timingis availabl
Page 647 and 648:
Instruction Cycle TimingTable 16-4
Page 649 and 650:
Instruction Cycle Timing16.2.7 Stat
Page 651 and 652:
Instruction Cycle TimingThe number
Page 653 and 654:
Instruction Cycle Timing16.3 Dual-i
Page 655 and 656:
Instruction Cycle TimingReplayevent
Page 657 and 658:
Instruction Cycle TimingPredicting
Page 659 and 660:
Instruction Cycle TimingUsing MCR i
Page 661 and 662:
Instruction Cycle TimingExample 16-
Page 663 and 664:
Page 665 and 666:
Instruction Cycle Timing16.6.3 Adva
Page 667 and 668:
Page 669 and 670:
Instruction Cycle Timing16.6.5 Adva
Page 671 and 672:
Page 673 and 674:
Instruction Cycle TimingFor example
Page 675 and 676:
Page 677 and 678:
Page 679 and 680:
Page 681 and 682:
Instruction Cycle Timing16.7 VFP in
Page 683 and 684:
Page 685 and 686:
Instruction Cycle Timing16.7.2 VFP
Page 687 and 688:
Chapter 17AC CharacteristicsThis ch
Page 689 and 690:
AC CharacteristicsThe timing parame
Page 691 and 692:
AC CharacteristicsTable 17-2 Timing
Page 693 and 694:
AC Characteristics17.4 APB interfac
Page 695 and 696:
AC Characteristics17.5 L1 and L2 MB
Page 697 and 698:
AC Characteristics17.7 DFT interfac
Page 699 and 700:
AC Characteristicsb. Figure 10-6 on
Page 701 and 702:
Appendix ASignal DescriptionsThis a
Page 703 and 704:
Signal DescriptionsA.2 ATB interfac
Page 705 and 706:
Signal DescriptionsTable A-3 MBIST
Page 707 and 708:
Signal DescriptionsA.4 Preload engi
Page 709 and 710:
Signal DescriptionsTable A-6 APB in
Page 711 and 712:
Signal DescriptionsTable A-7 Miscel
Page 713 and 714:
Page 715 and 716:
Page 717 and 718:
Signal DescriptionsA.8 Miscellaneou
Page 719 and 720:
Appendix BInstruction MnemonicsThis
Page 721 and 722:
Instruction MnemonicsTable B-1 Adva
Page 723 and 724:
Instruction MnemonicsB.2 VFP data-p
Page 725 and 726:
GlossaryThis glossary describes som
Page 727 and 728:
GlossaryApplication Specific Integr
Page 729 and 730:
GlossaryRead ID capabilityThe maxim
Page 731 and 732:
GlossaryByte-invariantIn a byte-inv
Page 733 and 734:
GlossaryCAM includes comparison log
Page 735 and 736:
GlossaryDouble-precision valueConsi
Page 737 and 738:
Glossary• arithmetic operation re
Page 739 and 740:
GlossaryInvalidateJazelle architect
Page 741 and 742:
GlossaryPAPenaltyPower-on resetPref
Page 743 and 744:
GlossarySetSet-associative cacheSee
Page 745 and 746:
GlossaryTrapTrigger instructionAn e
Page 747 and 748:
GlossaryWrite-back (WB)Write buffer
show all

Cortex-A8 R2P2.pdf - ARM Information Center

Create successful ePaper yourself

Delete template?

Save as template?