04.03.2013 Views

RL78/D1A User's Manual: Hardware - Renesas

RL78/D1A User's Manual: Hardware - Renesas

RL78/D1A User's Manual: Hardware - Renesas

SHOW MORE
SHOW LESS

Create successful ePaper yourself

Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.

<strong>RL78</strong>/<strong>D1A</strong><br />

RENESAS MCU<br />

1.1 Features<br />

Preliminary<br />

Specifications in this document are tentative and subject to change.<br />

CHAPTER 1 OUTLINE<br />

R01UH0317EJ0004<br />

Rev. 0.04<br />

Feb. 22, 2013<br />

Minimum instruction execution time can be changed from high speed (0.03125 s: @ 32 MHz operation with highspeed<br />

on-chip oscillator clock) to ultra low-speed (30.5 s: @ 32.768 kHz operation with subsystem clock)<br />

General-purpose register: 8 bits 32 registers (8 bits 8 registers 4 banks)<br />

ROM: 24 to 256 KB, RAM: 2 to 16 KB, Data flash memory: 8 KB<br />

On-chip high-speed on-chip oscillator clocks<br />

Select from 32 MHz (TYP.), 24 MHz (TYP.), 16 MHz (TYP.), 8 MHz (TYP.), and 4 MHz (TYP.)<br />

On-chip single-power-supply flash memory (with prohibition of block erase/writing function)<br />

Self-programming (with boot swap function/flash shield window function)<br />

On-chip debug function<br />

On-chip power-on-reset (POR) circuit and voltage detector (LVD)<br />

On-chip watchdog timer (operable with the dedicated low-speed on-chip oscillator clock)<br />

On-chip multiplier and divider/multiply-accumulator<br />

16 bits 16 bits = 32 bits (Unsigned or signed)<br />

32 bits 32 bits = 32 bits (Unsigned)<br />

16 bits 16 bits + 32 bits = 32 bits (Unsigned or signed)<br />

On-chip clock output/buzzer output controller<br />

On-chip BCD adjustment<br />

I/O ports: 38 to 84<br />

CMOS I/O port: 35 to 78 (LED direct drive port: 9 to 16, N-ch OD selectable port: 4 to 6)<br />

CMOS input port: 5<br />

CMOS output port: 0 to 1<br />

Timer<br />

16-bit timer: 24 channels<br />

Watchdog timer: 1 channel<br />

Real-time clock: 1 channel<br />

Interval timer: 1 channel<br />

Serial interface<br />

CSI<br />

UART (LIN-bus supported)<br />

Simplified I 2 C communication<br />

aFCAN controller<br />

Stepper motor controller/driver with zero point detection (ZPD): 1, 2, 4-channels<br />

LCD controller/driver (seg com): 27 4, 39 4, 48 4, 53 4<br />

Sound generator<br />

8/10-bit resolution A/D converter (VDD = EVDD =2.7 to 5.5 V): 5 to 9 channels<br />

Standby function: HALT, STOP, SNOOZE mode<br />

Power supply voltage: VDD = 2.7 to 5.5 V<br />

Operating ambient temperature: J grade products TA = 40 to +85C,<br />

L grade products TA = 40 to +105C<br />

Remark The functions mounted depend on the product. See 1.7 Outline of Functions.<br />

R01UH0317EJ0004 Rev. 0.04 1<br />

Feb. 22, 2013

Hooray! Your file is uploaded and ready to be published.

Saved successfully!

Ooh no, something went wrong!